2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  1. B240614
    Detach the 2 clips and remove the front door lower frame bracket garnish LH.


3. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

  1. B238520
    Using a moulding remover, detach the 3 claws and remove the inside handle bezel as shown in the illustration.


4. REMOVE ASSIST GRIP COVER LH

  1. B238521
    Using moulding remover A, detach the 8 claws and remove the assist grip cover.


5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B238522
    Remove the 3 screws.

  1. Remove the 12 clips.

  1. B238523E01
    Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.
    Text in Illustration 
    *1
    Reference Boss

  1. Raise the front door trim board sub-assembly to detach the 4 claws and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip LH.

  1. B238524
    Disconnect the 2 connectors.

  1. w/ Seat Position Memory System:

    1. B240206
      Disconnect the connectors.

  1. B238525
    Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.


6. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

  1. B238526
    Using a screwdriver, detach the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.


7. REMOVE FRONT DOOR SERVICE HOLE COVER LH

  1. B238530
    Remove the bolt.

  1. Detach the 2 clamps, move the wire harness out of the way and remove the service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.


8. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. B238531
    Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.

  1. B238532E01
    Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.


9. REMOVE FRONT DOOR GLASS RUN LH

  1. B238535
    Remove the front door glass run.


10. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

  1. B238536
    Remove the bolt and front door rear lower frame sub-assembly as shown in the illustration.


11. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY

  1. B238537
    Remove the hole plug.

  1. B238538
    Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.


12. REMOVE FRONT DOOR LOCK ASSEMBLY LH
  1. Disconnect the connector.

  1. B237872E01
    Using a T30 "TORX" wrench, remove the 3 screws.
    Text in Illustration 
    *A
    w/o Double Locking System
    *B
    w/ Double Locking System
    V100135
    Slide

  1. Slide the front door lock assembly downward, pull out the front door lock open rod from the outside handle frame, and remove the front door lock assembly and cables as a unit.

  1. Remove the front door lock open rod from the front door lock assembly.

  1. Remove the door lock wiring harness seal from the front door lock assembly.


13. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  1. B238548
    Remove the front door lock remote control cable assembly.


14. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

  1. B238549
    Using a screwdriver, detach the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. B238550
    Remove the front door inside locking cable assembly.

← REMOVAL (Aug 2013 – Jul 2014)INSPECTION (from Aug 2013) →