2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Side Monitor System)

B242850E01
  1. Apply battery voltage and check the operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1 (MV)
    Battery negative (-) → Terminal 9 (M+)
    Turns upward (A)
    Battery negative (-) → Terminal 1 (MV)
    Battery positive (+) → Terminal 9 (M+)
    Turns downward (B)
    Battery positive (+) → Terminal 8 (MH)
    Battery negative (-) → Terminal 9 (M+)
    Turns left (C)
    Battery negative (-) → Terminal 8 (MH)
    Battery positive (+) → Terminal 9 (M+)
    Turns right (D)

    If the result is not as specified, replace the outer rear view mirror assembly LH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly LH)

  1. B242854E01
    For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

    OK:
    Measurement Condition
    Mirror Position
    Specified Condition
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 10 (MF)
    Forward position (A)
    Moves from (A) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 10 (MF)
    Forward position (A)
    Does not move
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 10 (MF)
    Position between forward position (A) and driving position (C)
    Moves from (B) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 10 (MF)
    Position between forward position (A) and driving position (C)
    Moves from (B) to forward position (A)
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 10 (MF)
    Driving position (C)
    Moves from (C) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 10 (MF)
    Driving position (C)
    Does not move
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 10 (MF)
    Position between driving position (C) and retracted position (E)
    Moves from (D) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 10 (MF)
    Position between driving position (C) and retracted position (E)
    Moves from (D) to driving position (C)
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 10 (MF)
    Retracted position (E)
    Does not move
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 10 (MF)
    Retracted position (E)
    Moves from (E) to driving position (C)

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    1. Do not apply battery voltage when moving the mirror by hand into each mirror position.

    If the result is not as specified, replace the outer rear view mirror assembly LH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly LH)

  1. B242852E01
    w/ Mirror Heater:
    Check the mirror heater.

    1. Measure the resistance according to the value (s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 4 (+) - Terminal 11 (-)
      25°C (75°F)
      3.0 to 3.9 Ω

      If the result is not as specified, replace the outer rear view mirror assembly LH.

    2. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4 (+)
      Battery negative (-) → Terminal 11 (-)
      Mirror becomes warm

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly LH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Side Monitor System)

B242849E01
  1. Apply battery voltage and check the operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1 (MV)
    Battery negative (-) → Terminal 9 (M+)
    Turns upward (A)
    Battery negative (-) → Terminal 1 (MV)
    Battery positive (+) → Terminal 9 (M+)
    Turns downward (B)
    Battery positive (+) → Terminal 8 (MH)
    Battery negative (-) → Terminal 9 (M+)
    Turns left (C)
    Battery negative (-) → Terminal 8 (MH)
    Battery positive (+) → Terminal 9 (M+)
    Turns right (D)

    If the result is not as specified, replace the outer rear view mirror assembly RH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly RH)

  1. B242853E01
    For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

    OK:
    Measurement Condition
    Mirror Position
    Specified Condition
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 10 (MF)
    Forward position (A)
    Moves from (A) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 10 (MF)
    Forward position (A)
    Does not move
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 10 (MF)
    Position between forward position (A) and driving position (C)
    Moves from (B) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 10 (MF)
    Position between forward position (A) and driving position (C)
    Moves from (B) to forward position (A)
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 10 (MF)
    Driving position (C)
    Moves from (C) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 10 (MF)
    Driving position (C)
    Does not move
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 10 (MF)
    Position between driving position (C) and retracted position (E)
    Moves from (D) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 10 (MF)
    Position between driving position (C) and retracted position (E)
    Moves from (D) to driving position (C)
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 10 (MF)
    Retracted position (E)
    Does not move
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 10 (MF)
    Retracted position (E)
    Moves from (E) to driving position (C)

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    1. Do not apply battery voltage when moving the mirror by hand into each mirror position.

    If the result is not as specified, replace the outer rear view mirror assembly RH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly RH)

  1. B242851E01
    w/ Mirror Heater:
    Check the mirror heater.

    1. Measure the resistance according to the value (s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 4 (+) - Terminal 11 (-)
      25°C (75°F)
      3.0 to 3.9 Ω

      If the result is not as specified, replace the outer rear view mirror assembly RH.

    2. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4 (+)
      Battery negative (-) → Terminal 11 (-)
      Mirror becomes warm

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly RH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Side Monitor System)

B199929E01
  1. Apply battery voltage and check the operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 6 (MV)
    Battery negative (-) → Terminal 5 (M+)
    Turns upward (A)
    Battery negative (-) → Terminal 6 (MV)
    Battery positive (+) → Terminal 5 (M+)
    Turns downward (B)
    Battery positive (+) → Terminal 4 (MH)
    Battery negative (-) → Terminal 5 (M+)
    Turns left (C)
    Battery negative (-) → Terminal 4 (MH)
    Battery positive (+) → Terminal 5 (M+)
    Turns right (D)

    If the result is not as specified, replace the outer rear view mirror assembly LH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly LH)

  1. B199933E01
    w/ Retract Mirror:
    For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

    OK:
    Measurement Condition
    Mirror Position
    Specified Condition
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 9 (MF)
    Forward position (A)
    Moves from (A) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 9 (MF)
    Forward position (A)
    Does not move
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 9 (MF)
    Position between forward position (A) and driving position (C)
    Moves from (B) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 9 (MF)
    Position between forward position (A) and driving position (C)
    Moves from (B) to forward position (A)
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 9 (MF)
    Driving position (C)
    Moves from (C) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 9 (MF)
    Driving position (C)
    Does not move
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 9 (MF)
    Position between driving position (C) and retracted position (E)
    Moves from (D) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 9 (MF)
    Position between driving position (C) and retracted position (E)
    Moves from (D) to driving position (C)
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 9 (MF)
    Retracted position (E)
    Does not move
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 9 (MF)
    Retracted position (E)
    Moves from (E) to driving position (C)

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    1. Do not apply battery voltage when moving the mirror by hand into each mirror position.

    If the result is not as specified, replace the outer rear view mirror assembly LH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly LH)

  1. B242855E01
    w/ Mirror heater:
    Check the mirror heater.

    1. Measure the resistance according to the value (s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 2 (+) - Terminal 8 (-)
      25°C (75°F)
      3.0 to 3.9 Ω

      If the result is not as specified, replace the outer rear view mirror assembly LH.

    2. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2 (+)
      Battery negative (-) → Terminal 8 (-)
      Mirror becomes warm

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly LH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Side Monitor System)

B199928E01
  1. Apply battery voltage and check the operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 6 (MV)
    Battery negative (-) → Terminal 5 (M+)
    Turns upward (A)
    Battery negative (-) → Terminal 6 (MV)
    Battery positive (+) → Terminal 5 (M+)
    Turns downward (B)
    Battery positive (+) → Terminal 4 (MH)
    Battery negative (-) → Terminal 5 (M+)
    Turns left (C)
    Battery negative (-) → Terminal 4 (MH)
    Battery positive (+) → Terminal 5 (M+)
    Turns right (D)

    If the result is not as specified, replace the outer rear view mirror assembly RH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly RH)

  1. B199932E01
    w/ Retract Mirror:
    For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

    OK:
    Measurement Condition
    Mirror Position
    Specified Condition
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 9 (MF)
    Forward position (A)
    Moves from (A) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 9 (MF)
    Forward position (A)
    Does not move
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 9 (MF)
    Position between forward position (A) and driving position (C)
    Moves from (B) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 9 (MF)
    Position between forward position (A) and driving position (C)
    Moves from (B) to forward position (A)
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 9 (MF)
    Driving position (C)
    Moves from (C) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 9 (MF)
    Driving position (C)
    Does not move
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 9 (MF)
    Position between driving position (C) and retracted position (E)
    Moves from (D) to retracted position (E)
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 9 (MF)
    Position between driving position (C) and retracted position (E)
    Moves from (D) to driving position (C)
    Battery positive (+) → Terminal 3 (MR)
    Battery negative (-) → Terminal 9 (MF)
    Retracted position (E)
    Does not move
    Battery negative (-) → Terminal 3 (MR)
    Battery positive (+) → Terminal 9 (MF)
    Retracted position (E)
    Moves from (E) to driving position (C)

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    1. Do not apply battery voltage when moving the mirror by hand into each mirror position.

    If the result is not as specified, replace the outer rear view mirror assembly RH.
    Text in Illustration 
    *a
    Component without harness connected
    (Outer Rear View Mirror Assembly RH)

  1. B242856E01
    w/ Mirror Heater:
    Check the mirror heater.

    1. Measure the resistance according to the value (s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 2 (+) - Terminal 8 (-)
      25°C (75°F)
      3.0 to 3.9 Ω

      If the result is not as specified, replace the outer rear view mirror assembly RH.

    2. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2 (+)
      Battery negative (-) → Terminal 8 (-)
      Mirror becomes warm

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly RH.
      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)

← DISASSEMBLY (from Aug 2014)REASSEMBLY (Aug 2013 – Jul 2014) →