2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the and LH sides.
  2. The procedure listed below is for the LH side.
  3. w/ Side Monitor System:
    When installing only the side television camera assembly, refer to TELEVISION CAMERA (for Side) (Click here).


1. REMOVE OUTER REAR VIEW MIRROR GLASS

B231562E01
  1. Push the upper part of the mirror surface and tilt it.

  1. Using a moulding remover, detach the 4 claws and separate the outer rear view mirror glass from the mirror body.

    HINT:
    Apply protective tape to the outer rear view mirror to prevent it from being damaged.

    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the connectors and remove the mirror glass.


2. REMOVE OUTER MIRROR COVER LH

B241698E02

HINT:
Be sure to detach the claws of the outer mirror cover in the order shown in the illustration.

  1. B245779E01
    Using 2 screwdrivers, detach the 2 claws.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover.

    NOTICE:
    Be careful not to break the ribs.

    HINT:
    Tape the screwdriver tip before use.


    B245757E01
    Text in Illustration 
    *1
    Protective Tape
    *2
    Rib
    *a
    Inner Side of Outer Mirror Cover
    -
    -

  1. B245758E01
    Insert a moulding remover into the space made between the outer mirror body and outer mirror cover.

    NOTICE:
    Do not insert the moulding remover more than 4 mm (0.157 in.).

    HINT:
    Tape the moulding remover before use.

    Text in Illustration 
    *1
    Protective Tape

  1. B245770E01
    Slide the moulding remover downwards as shown in the illustration to detach the 2 claws.

    NOTICE:
    1. Do not insert the moulding remover more than 4 mm (0.157 in.).
    2. Do not slide the moulding remover past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover as the outer mirror body will become damaged.

    Standard:
    Area
    Specified Condition
    a
    40.0 mm (1.57 in.)

  1. Remove the moulding remover.

  1. B245762E01
    Insert a moulding remover between the outer mirror cover and outer mirror body as shown in the illustration and detach the claw.
    Text in Illustration 
    *1
    Protective Tape

  1. B245633E01
    Using a screwdriver, detach the claw.
    Text in Illustration 
    *1
    Protective Tape

  1. B245761
    Detach the 2 claws and remove the outer mirror cover.

    NOTICE:
    When removing the cover, be careful not to damage the side turn signal light assembly or cover.


3. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

  1. E199248
    Remove the 3 screws and light.

  1. Disconnect the connector.


4. REMOVE OUTER MIRROR RETRACTOR LH

  1. Remove the outer rear view mirror gasket LH.

    1. B279036E01
      Cut the wire harness sub-assembly at the location shown in the illustration.

      HINT:
      A new wire harness sub-assembly is used for reassembly.

      Text in Illustration 
      *a
      Cut here

    2. B279037E01
      Remove the tape and detach the clamp.
      Text in Illustration 
      *1
      Tape
      *2
      Clamp

  1. B245738E01
    Remove the screw, detach the 5 claws and remove the outer rear view mirror gasket LH.

  1. Remove the lower mirror cover.

    1. B245769E01
      B278450E01
      Put protective tape around the lower mirror cover.
      Text in Illustration 
      *1
      Protective Tape

      HINT:
      The claws of the mirror will be detached in the order shown in the illustration in the following steps.

    2. B245741E02
      Using a screwdriver, detach the claw.
      Text in Illustration 
      *1
      Protective Tape

    3. B245742E01
      Using a screwdriver, detach the claw.
      Text in Illustration 
      *1
      Protective Tape

    4. B245765E01
      Using a screwdriver, detach the claw to create a space between the lower mirror cover and mirror body as shown in the illustration.
      Text in Illustration 
      *1
      Protective Tape

    5. B245768E01
      Insert a screwdriver as shown in the illustration.
      Text in Illustration 
      *1
      Protective Tape

    6. B245766E01
      Detach the claw to create a space between the lower mirror cover and cover base as shown in the illustration.
      Text in Illustration 
      *1
      Protective Tape

    7. B245767
      While moving the lower mirror cover back and forth in the directions of the arrows in the illustration, detach the 3 claws and remove the lower mirror cover.

  1. B236356
    Using a T25 "TORX" socket wrench, remove the 3 screws.

  1. B236362E01
    w/ Side Monitor System:

    1. Remove the connector from the wire clip.

    2. Disconnect the connector.

      NOTICE:
      When disconnecting the connector, be careful not to damage it.

      Text in Illustration 
      *1
      Protective Tape

  1. B241697
    Remove the 5 screws and outer mirror body.

  1. B279038E01
    Detach the claw and remove the cover body.

    NOTICE:
    Be careful as the claw shown in the part of the illustration labeled A is easily damaged.

    Text in Illustration 
    *a
    A

  1. Remove the actuator sub-assembly.

    1. B278468E01
      Slide the cover as shown in the illustration and disconnect the connector.

    2. B279040E03
      Pull out the wire harness sub-assembly in the direction indicated by the arrow in the illustration.

    3. B279041
      Remove the 3 screws and actuator sub-assembly.

    4. B279042
      Detach the clamp.

    5. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the two claws and disconnect the connector.

  1. w/ Side Monitor System:

    1. B279043
      Detach the claw and remove the wire clip.

  1. Remove the support spring.

    1. B279044
      Remove the 2 screws, and then detach the 6 claws and remove the 2 support springs.


5. REMOVE SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)
  1. Remove the side television camera assembly (Click here).

← DISASSEMBLY (Aug 2013 – Jul 2014)INSPECTION (from Aug 2013) →