DATA LIST / ACTIVE TEST
System information · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Data List.
According to the display on the tester, read the Data List.
ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
-
Engine Speed
Engine speed/
Min.: 0 rpm
Max.: 16383 rpm
Engine idling: 650 to 750 rpm
-
Calculate Load
Load calculated by ECM/
Min.: 0.0%
Max.: 100.0%
- Engine idling: 7 to 26%
- Running without load (2500 rpm): 10 to 20%
-
Coolant Temp
Engine coolant temperature/
Min.: -40°C (-40°F)
Max.: 140°C (284°F)
After warming up engine: 75 to 90°C (167 to 194°F)
- If the value is -40°C (-40°F), the sensor circuit is open.
- If the value is 140°C (284°F), the sensor circuit is shorted.
Engine Run Time
Engine run time/
Min.: 0 seconds
Max.: 65535 seconds
Time after engine start
-
Battery Voltage
Battery voltage/
Min.: 0 V
Max.: 65.5 V
Engine idling: 11 to 14 V
-
Starter Signal
Starter signal/
ON or OFF
- ON: Engine cranking
- OFF: Engine not cranking
-
Neutral Position SW Signal
PNP switch status/
ON or OFF
- ON: Shift lever in P or N
- OFF: Shift lever not in P or N
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Stop Light Switch
Stop light switch status/
ON or OFF
- ON: Brake pedal depressed
- OFF: Brake pedal released
-
# Codes(Include History)
Number of codes/
Min.: 0
Max.: 255
-
Number of DTCs stored
MIL ON Run Distance
Distance driven after MIL turns on/
Min.: 0 km (0 mile),
Max.: 65535 km (40723 mile)
Distance driven after DTC stored
-
Running Time from MIL ON
Running time from MIL on/
Min.: 0 minutes
Max.: 65535 minutes
Equivalent to running time after MIL turns on
-
Time after DTC Cleared
Time after DTC cleared/
Min.: 0 minutes
Max.: 65535 minutes
Equivalent to time after DTCs cleared
-
Distance from DTC Cleared
Distance driven after DTC cleared/
Min.: 0 km (0 mile)
Max.: 65535 km (40723 mile)
Equivalent to distance driven after DTCs cleared
-
Warmup Cycle Cleared DTC
Warmup cycles after DTC cleared/
Min.: 0, Max.: 255
Number of warmup cycles after DTCs cleared
-
Engine Speed from EFI
Engine speed/
Min.: 0 rpm
Max.: 16383 rpm
Engine idling: 650 to 750 rpm
Engine speed received from the ECM.
Intake-Air Temp from EFI
Intake air temperature/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
Equivalent to temperature at intake manifold
Intake air temperature received from the ECM.
Coolant Temp from EFI
Engine coolant temperature/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
After warming up: 75 to 90°C (167 to 194°F)
Coolant temperature received from the ECM.
Accel Position from EFI
Absolute accelerator pedal position/
Min.: 0.0%
Max.: 100.0%
- Accelerator pedal released: 0%
- Accelerator pedal fully depressed: 100%
Accelerator position received from the ECM.
Injection Volume from EFI
Injection volume/
Min.: 0.00 mm3/st
Max.: 639.96 mm3/st
Engine idling: 3.0 to 10 mm3/st
Injection volume received from the ECM.
SPD (NT)
Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
- Lock-up ON (after warming up engine): Input turbine speed (NT) equal to engine speed
- Lock-up OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
Data is displayed in increments of 50 rpm.
SPD (SP2)
Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed)
-
Shift SW Status (P Range)
PNP switch status/
ON or OFF
- ON: Shift lever in P
- OFF: Shift lever not in P
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (R Range)
PNP switch status/
ON or OFF
- ON: Shift lever in R
- OFF: Shift lever not in R
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (N Range)
PNP switch status/
ON or OFF
- ON: Shift lever in N
- OFF: Shift lever not in N
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Sports Shift Up SW
Sport shift up switch status/
ON or OFF
- ON: Shift lever held in "+" (up-shift)
- OFF: Shift lever not held in "+" (up-shift)
-
Sports Shift Down SW
Sport shift down switch status/
ON or OFF
- ON: Shift lever held in "-" (down-shift)
- OFF: Shift lever not held in "-" (down-shift)
-
Sports Mode Selection SW
Sport mode select switch status/
ON or OFF
- ON: Shift lever in S, "+" or "-"
- OFF: Shift lever not in S, "+" or "-"
-
Snow Switch Status
Pattern select (2nd) switch status/
ON or OFF
- ON: Pattern select (2nd) switch pushed
- OFF: Pattern select (2nd) switch not pushed
-
Shift SW Status (D Range)
PNP switch status/
ON or OFF
- ON: Shift lever in D, S, "+" or "-"
- OFF: Shift lever not in D, S, "+" or "-"
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
A/T Oil Temperature 1
No. 1 ATF temperature sensor value/
Min.: -40.0°C (-40.0°F)
Max.: 215.0°C (419.0°F)
- After stall test: Approximately 80°C (176°F)
- With engine cold: Equal to ambient temperature
If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted.
A/T Oil Temperature 2
No. 2 ATF temperature sensor value/
Min.: -40.0°C (-40.0°F)
Max.: 215.0°C (419.0°F)
- After stall test: Approximately 80°C (176°F)
- With engine cold: Equal to ambient temperature
If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted.
Lock Up
Lock-up/
ON or OFF
- ON: Lock-up operating
- OFF: Lock-up not operating
-
Lock Up Solenoid Status
Shift solenoid valve SLU status/
ON or OFF
- ON: Shift solenoid valve SLU operating
- OFF: Shift solenoid valve SLU not operating
-
Shift Status
TCM gear shift command/
1st, 2nd, 3rd, 4th or 5th
- 1st, 2nd, 3rd, 4th or 5th: Shift lever in D
- 1st, 2nd, 3rd, 4th or 5th: Shift lever in S
-
SLT Solenoid Status
Shift solenoid SLT status/
ON or OFF
- OFF: Accelerator pedal depressed
- ON: Accelerator pedal released
-
SLU Solenoid Status
Shift solenoid SLU status/
ON or OFF
- ON: Shift solenoid SLU operating
- OFF: Shift solenoid SLU not operating
-
Snow or 2nd Start Mode
2nd start mode status/
ON or OFF
ON: 2nd start mode on
OFF: 2nd start mode off
-
- Engine idling: 7 to 26%
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the tester, perform the Active Test.
ECT Tester Display
Test Part
Control Range
Diagnostic Note
Connect the TC and TE1
Turn on and off TC and TE1 connection
ON or OFF
-
Activate the Solenoid (SLU)
Operate shift solenoid valve SLU
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Solenoid (SLT)*
Operate shift solenoid valve SLT and raise line pressure
ON or OFF - HINT:
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
- ON: No action (normal operation)
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
[Vehicle Condition] - Vehicle stopped
- Engine idling
Activate the Solenoid (S1)
Operate shift solenoid valve S1
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Solenoid (S2)
Operate shift solenoid valve S2
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Lock Up
Control shift solenoid valve SLU to set automatic transmission to lock-up
ON or OFF
Possible to check shift solenoid valve SLU operation.
[Vehicle Condition]- Throttle valve opening angle: Less than 35%
- Vehicle speed: 80 km/h (50 mph) or more
Control the Shift Position
Operate shift solenoid valves and set each shift position
- Press "→" button: Shift up
- Press "←" button: Shift down
Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (31 mph) or less
Activate the Solenoid (SR)
Operate shift solenoid valve SR
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Solenoid (SL1)
Operate shift solenoid valve SL1
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
Activate the Solenoid (SL2)
Operate shift solenoid valve SL2
ON or OFF
[Vehicle Condition] - Engine stopped
- Shift lever in P or N
- HINT:
- *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and hydraulic test are different.
- Engine stopped