2013-2015 Land Cruiser Prado · Service Manual Drivetrain

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the TCM.
DTC Code
DTC Detection Condition
Trouble Area
P0705
One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
  1. P input signal
  2. N input signal
  3. NSW input signal
  4. R input signal
  5. D input signal
(B) Any of the following signals is ON for 2.0 sec. or more with the shift lever in S (2-trip detection logic):
  1. P input signal
  2. N input signal
  3. NSW input signal
  4. R input signal
(C) P, R, N, D and NSW switches are OFF simultaneously (2-trip detection logic).
  1. Open or short in park/neutral position switch circuit
  2. Transmission control switch (transmission floor shift assembly)
  3. Park/neutral position switch
  4. TCM

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the TCM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the TCM according to the shift lever position (P, R, N, D or S).
The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C251066E01

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the intelligent tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in P or N
    2. OFF: Shift lever not in P or N
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (P Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in P
    2. OFF: Shift lever not in P
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in R
    2. OFF: Shift lever not in R
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Shift SW Status (N Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in N
    2. OFF: Shift lever not in N
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Shift lever held in "+" (up-shift)
    2. OFF: Shift lever not held in "+" (up-shift)
    -
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Shift lever held in "-" (down-shift)
    2. OFF: Shift lever not held in "-" (down-shift)
    -
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    1. ON: Shift lever in S, "+" or "-"
    2. OFF: Shift lever not in S, "+" or "-"
    -
    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever in D, S, "+" or "-"
    2. OFF: Shift lever not in D, S, "+" or "-"
    When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.


1. CHECK HARNESS AND CONNECTOR (ECU-IG NO. 1 FUSE - PARK/NEUTRAL POSITION SWITCH)

  1. C197711E30
    Disconnect the C40 park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C40-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V
    C40-2 (RB) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

  1. C294510E07
    Disconnect the C40 park/neutral position switch connector.

  1. Disconnect the C92 ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C40-4 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    C40-4 (B) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch)



NG
Go to step 7
OK


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C197712E13
    Disconnect the C40 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1. 2 (RB) - 6 (PL)
    2. 4 (B) - 5 (L)
    Shift lever in P
    Below 1 Ω
    2 (RB) - 1 (RL)
    Shift lever in R
    Below 1 Ω
    1. 2 (RB) - 9 (NL)
    2. 4 (B) - 5 (L)
    Shift lever in N
    Below 1 Ω
    2 (RB) - 7 (DL)
    Shift lever in D, S, "+" or "-"
    Below 1 Ω
    1. 2 (RB) - 6 (PL)
    2. 4 (B) - 5 (L)
    Shift lever not in P
    10 kΩ or higher
    2 (RB) - 1 (RL)
    Shift lever not in R
    10 kΩ or higher
    1. 2 (RB) - 9 (NL)
    2. 4 (B) - 5 (L)
    Shift lever not in N
    10 kΩ or higher
    2 (RB) - 7 (DL)
    Shift lever not in D, S, "+" or "-"
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Park/Neutral Position Switch)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (ECU-IG NO. 1 FUSE - TRANSMISSION CONTROL SWITCH)

  1. C203343E19
    Disconnect the G47 transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G47-3 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    G47-3 (IG) - Body ground
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transmission Control Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT TRANSMISSION CONTROL SWITCH

  1. C203344E14
    Disconnect the G47 transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (IG) - 7 (S)
    Shift lever in S, "+" or "-"
    Below 1 Ω
    3 (IG) - 7 (S)
    Shift lever not in S, "+" or "-"
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Control Switch)



NG
REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY) (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - TCM)

  1. C296047E01
    Disconnect all the connectors from the TCM.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G69-13 (P) - Body ground
    1. Ignition switch ON
    2. Shift lever in P
    11 to 14 V
    G71-9 (R) - Body ground
    1. Ignition switch ON
    2. Shift lever in R
    11 to 14 V*
    G69-14 (N) - Body ground
    1. Ignition switch ON
    2. Shift lever in N
    11 to 14 V
    G71-8 (D) - Body ground
    1. Ignition switch ON
    2. Shift lever in D
    11 to 14 V
    G70-15 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever in S, "+" or "-"
    11 to 14 V
    G69-13 (P) - Body ground
    1. Ignition switch ON
    2. Shift lever not in P
    Below 1 V
    G71-9 (R) - Body ground
    1. Ignition switch ON
    2. Shift lever not in R
    Below 1 V
    G69-14 (N) - Body ground
    1. Ignition switch ON
    2. Shift lever not in N
    Below 1 V
    G71-8 (D) - Body ground
    1. Ignition switch ON
    2. Shift lever not in D
    Below 1 V
    G70-15 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever not in S, "+" or "-"
    Below 1 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to TCM)

    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM (Click here)

7. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
  1. Disconnect the C40 park/neutral position switch connector.

  1. Disconnect the G69 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C40-4 (B) - G69-12 (NSW)
    Always
    Below 1 Ω
    C40-4 (B) - Body ground
    Always
    10 kΩ or higher
    G69-12 (NSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM (Click here)


← P0617 Starter Relay Circuit High (from Aug 2014)P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (from Aug 2014) →