2013-2015 Land Cruiser Prado · Service Manual Drivetrain

P2742 Transmission Fluid Temperature Sensor "B" Circuit Low Input

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTC P2741 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
P2742
No. 1 ATF temperature sensor voltage is below 0.142 V for 0.5 sec. or more (1-trip detection logic).
  1. Short in No. 1 ATF temperature sensor circuit
  2. No. 1 ATF temperature sensor (transmission wire)
  3. ECM
P2743
When 15 minutes or more have elapsed after the engine is started, No. 1 ATF temperature sensor voltage is higher than 4.915 V for 0.5 sec. or more (1-trip detection logic).
  1. Open in No. 1 ATF temperature sensor circuit
  2. No. 1 ATF temperature sensor (transmission wire)
  3. ECM

MONITOR DESCRIPTION

The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the ATF temperature sensor circuit. If the output voltage of the ATF temperature sensor is below 0.142 V*1 or higher than 4.915 V*2, the ECM interprets this as a fault in the ATF temperature sensor or wiring. The ECM will illuminate the MIL and store the DTC.

HINT:
  1. *1: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.
  2. *2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.
  3. The ATF temperature can be checked on the intelligent tester display.


WIRING DIAGRAM

C214972E01

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the tester, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 150°C (302°F)
    1. After stall test: Approximately 80°C (176°F)
    2. Equal to ambient temperature when engine cold
    If the value is -40°C (-40°F) or 150°C (302°F), the No. 1 ATF temperature sensor circuit is open or shorted.

    HINT:
    When DTC P2742 is output and the intelligent tester output is 150°C (302°F) or higher, there is a short circuit.
    When DTC P2743 is output and the intelligent tester output is -40°C (-40°F), there is an open circuit.
    Check the temperature displayed on the tester in order to check if a malfunction exists.

    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or higher
    Short circuit


1. INSPECT TRANSMISSION WIRE (NO. 1 ATF TEMPERATURE SENSOR)

  1. C214964E01
    Disconnect the C58 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (OT2+) - 5 (OT2-)
    Always
    79 Ω to 156 kΩ
    1 (OT2+) - Body ground
    Always
    10 kΩ or higher
    5 (OT2-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

    Standard Resistance:
    ATF Temperature
    Specified Condition
    10°C (50°F)
    5 to 8 kΩ
    25°C (77°F)
    2.5 to 4.5 kΩ
    110°C (230°F)
    0.22 to 0.28 kΩ

Text in Illustration 
*a
Component without harness connected
(Transmission Wire)


NG
REPAIR OR REPLACE NO. 1 ATF TEMPERATURE SENSOR (TRANSMISSION WIRE) (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C214336E07
    Disconnect the C62 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C62-18 (THO1) - C62-17 (ETHO)
    Always
    79 Ω to 156 kΩ
    C62-18 (THO1) - Body ground
    Always
    10 kΩ or higher
    C62-17 (ETHO) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P2742 Transmission Fluid Temperature Sensor "B" Circuit Low Input (+ P2743) (Aug 2013 – Jul 2014)P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) (Aug 2013 – Jul 2014) →