2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0504 Brake Switch "A" / "B" Correlation

Diagnostic trouble codes · Vehicles built from Aug 2013

DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If signals which indicate the brake pedal is being depressed and released are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:
The normal switch conditions are shown in the table below.

Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) The ignition switch is ON.
(b) The brake pedal is released.
(c) The STP signal is off when the ST1- signal is off.
  1. Open or short in stop light switch assembly signal circuit
  2. Stop light switch assembly
  3. ECM

WIRING DIAGRAM

A309934E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. STP signal conditions can be checked using the intelligent tester.
    1. Connect the intelligent tester to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the tester on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.
    5. Check the STP signal when the brake pedal is depressed and released.
      Brake Pedal Operation
      Specified Condition
      Depressed
      STP signal ON
      Released
      STP signal OFF


1. CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)

  1. E233265E83
    Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A85-1 (B) - Body ground
    Always
    11 to 14 V
    A85-5 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)

  1. Reconnect the stop light switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - INTEGRATION RELAY, BATTERY)
OK


2. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
  1. Disconnect the stop light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A85-3 (GND) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the stop light switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK ECM (STP AND ST1- VOLTAGE)

  1. A177861E35
    Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Brake Pedal Operation
    Specified Condition
    G59-8 (ST1-) - Body ground
    Brake pedal released
    7.5 to 14 V
    Brake pedal depressed
    Below 1.5 V
    G60-18 (STP) - Body ground
    Brake pedal released
    Below 1.5 V
    Brake pedal depressed
    7.5 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 4
OK

REPLACE ECM (Click here)

4. CHECK HARNESS AND CONNECTOR
  1. Disconnect the stop light switch assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A85-2 (L) - G60-18 (STP)
    Always
    Below 1 Ω
    A85-4 (L) - G59-8 (ST1-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A85-2 (L) or G60-18 (STP) - Body ground
    Always
    10 kΩ or higher
    A85-4 (L) or G59-8 (ST1-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the stop light switch assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)


← P0500 Vehicle Speed Sensor (from Aug 2013)P0505 Idle Control System (Aug 2013 – Jul 2014) →