P0504 Brake Switch "A" / "B" Correlation
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.- HINT:
- The normal switch conditions are as shown in the table below.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0504 |
Conditions (a), (b) and (c) are met for 0.5 seconds or more (1 trip detection logic): (a) The ignition switch is ON. (b) The brake pedal is released. (c) The STP signal is OFF when the ST1- signal is OFF. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- STP signal conditions can be checked using the intelligent tester.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the tester on.
- Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.
- Check the STP signal when the brake pedal is depressed and released.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| Brake Pedal Operation |
Specified Condition |
| Depressed |
STP signal ON |
| Released |
STP signal OFF |
| 1. CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE) |
![]() ![]() |
Disconnect the stop light switch connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
A85-1 (B) - Body ground
Always
11 to 14 V
A85-5 (B) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Stop Light Switch)
Reconnect the stop light switch connector.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND) |
Disconnect the stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A85-3 (GND) - Body ground
Always
Below 1 Ω
Reconnect the stop light switch assembly connector.
|
|
||||
| OK | |
| 3. CHECK ECM (STP AND ST1 - VOLTAGE) |
![]() ![]() |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G55-8 (ST1-) - Body ground
Brake pedal released
11 to 14 V
Brake pedal depressed
0 to 3 V
G56-18 (STP) - Body ground
Brake pedal released
0 to 3 V
Brake pedal depressed
11 to 14 V
Text in Illustration *a
Brake Pedal Depressed
*b
Brake Pedal Released
*c
Component with harness connected
(ECM)
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM) |
Disconnect the stop light switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
A85-2 (L) - G56-18 (STP)
Always
Below 1 Ω
A85-4 (L) - G55-8 (ST1-)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
A85-2 (L) or G56-18 (STP) - Body ground
Always
10 kΩ or higher
A85-4 (L) or G55-8 (ST1-) - Body ground
Always
10 kΩ or higher
Reconnect the stop light switch assembly connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||


