2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

TERMINALS OF ECU

System information · Vehicles built from Aug 2013


CHECK POWER MANAGEMENT CONTROL ECU
C201247E09
  1. Disconnect the G51 power management control ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G51-1 (AM22) - Body ground
    B - Body ground
    +B power supply
    Always
    9.5 to 14 V
    G51-2 (AM21) - Body ground
    B - Body ground
    +B power supply
    Always
    9.5 to 14 V
    G51-5 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    G51-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    G51-17 (SSW2) - Body ground
    R - Body ground
    Engine switch signal
    Engine switch pushed
    Below 1 Ω
    G51-17 (SSW2) - Body ground
    R - Body ground
    Engine switch signal
    Engine switch not pushed
    10 kΩ or higher
    G51-18 (SSW1) - Body ground
    LG - Body ground
    Engine switch signal
    Engine switch pushed
    Below 1 Ω
    G51-18 (SSW1) - Body ground
    LG - Body ground
    Engine switch signal
    Engine switch not pushed
    10 kΩ or higher
    G51-24 (LIN2) - Body ground
    G - Body ground
    LIN line
    Always
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the G51 power management control ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G51-3 (SLP) - G51-6 (GND)
    SB - W-B
    Steering lock actuator position signal
    Steering lock released
    Pulse generation
    (See waveform 1)
    G51-3 (SLP) - G51-6 (GND)
    SB - W-B
    Steering lock actuator position signal
    Steering lock locked
    Pulse generation
    (See waveform 1)
    G51-8 (SLR+) - G51-6 (GND)
    W - W-B
    Steering lock motor signal
    Steering lock motor operating
    Below 1 V
    G51-8 (SLR+) - G51-6 (GND)
    W - W-B
    Steering lock motor signal
    Steering lock motor not operating
    11 to 14 V
    G51-10 (INDW) - G51-6 (GND)
    L - W-B
    Warning signal
    for Manual Transmission:
    1. Clutch pedal depressed
    2. Engine switch on (ACC) or on (IG)
    for Automatic Transmission:
    1. Brake pedal depressed
    2. Shift lever in P
    3. Engine switch on (ACC) or on (IG)
    8 to 14 V
    G51-16 (P) - G51-6 (GND)
    V - W-B
    Shift lock signal
    Shift lever in P*1
    8 to 14 V
    G51-16 (P) - G51-6 (GND)
    V - W-B
    Shift lock signal
    Shift lever not in P*1
    Below 1 V
    G51-19 (ACCD) - G51-6 (GND)
    R - W-B
    ACC signal
    Engine switch on (ACC)
    8 to 14 V
    G51-19 (ACCD) - G51-6 (GND)
    R - W-B
    ACC signal
    Engine switch off
    Below 1 V
    G51-20 (IG1D) - G51-6 (GND)
    V - W-B
    IG1 signal
    Engine switch on (IG)
    8 to 14 V
    G51-20 (IG1D) - G51-6 (GND)
    V - W-B
    IG1 signal
    Engine switch on (ACC)
    Below 1 V
    G51-22 (INDS) - G51-6 (GND)
    B - W-B
    Vehicle condition signal
    for Manual Transmission:
    1. Clutch pedal depressed
    for Automatic Transmission:
    1. Brake pedal depressed
    2. Shift lever in P
    8 to 14 V
    G51-23 (SPD) - G51-6 (GND)
    R - W-B
    Vehicle speed signal
    Engine switch on (IG), vehicle being driven at approx. 20 km/h (12 mph)
    Pulse generation
    (See waveform 2)
    G50-2 (STA) - G51-6 (GND)
    W - W-B
    Park/neutral position switch*1 or clutch start switch*2 signal
    for Manual Transmission:
    1. Clutch pedal depressed
    for Automatic Transmission:
    1. Shift lever in P or N
    Below 1 V
    G50-3 (STAR) - G51-6 (GND)
    B - W-B
    Starter signal
    for Manual Transmission:
    1. Clutch pedal depressed
    2. Engine cranking
    for Automatic Transmission:
    1. Brake pedal depressed
    2. Shift lever in P
    3. Engine cranking
    8 to 14 V*3
    G50-8 (IG2D) - G51-6 (GND)
    L - W-B
    IG2 signal
    Engine switch on (IG)
    8 to 14 V
    G50-8 (IG2D) - G51-6 (GND)
    L - W-B
    IG2 signal
    Engine switch on (ACC)
    Below 1 V
    G50-11 (STP1) - G51-6 (GND)
    V - W-B
    Stop light signal
    Brake pedal depressed*1
    8 to 14 V
    G50-11 (STP1) - G51-6 (GND)
    V - W-B
    Stop light signal
    Brake pedal released*1
    Below 1 V
    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission
    3. *3: Voltage is output for 0.3 seconds when the engine is cranking. Disconnect the connector from the ECM before measuring the voltage.
    If the result is not as specified, the ECU may have a malfunction.

  5. Using an oscilloscope, check the signal waveform of the ECU.

    1. A130277E04
      Waveform 1
      Waveform 1 (Reference) 
      Terminal No. (Symbol)
      G51-3 (SLP) - G51-6 (GND)
      Tool Setting
      2 V/DIV., 100 ms./DIV.
      Vehicle Condition
      Steering lock locked or released

    2. I042329E01
      Waveform 2
      Waveform 2 (Reference) 
      Terminal No. (Symbol)
      G51-23 (SPD) - G51-6 (GND)
      Tool Setting
      5 V/DIV., 10 ms./DIV.
      Vehicle Condition
      Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

      HINT:
      As the vehicle speed increases, the wavelength shortens.


CHECK CERTIFICATION ECU
B197893E21
  1. Disconnect the G38 certification ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G38-1 (+B) - Body ground
    V - Body ground
    +B power supply
    Always
    11 to 14 V
    G38-15 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    G38-29 (LIN) - Body ground
    G - Body ground
    LIN line
    Always
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK STEERING LOCK ECU
C104383E13
  1. Disconnect the G35 steering lock ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G35-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    G35-6 (IG2) - Body ground
    W - Body ground
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    G35-6 (IG2) - Body ground
    W - Body ground
    Ignition power supply
    Engine switch off
    Below 1 V
    G35-7 (B) - Body ground
    G - Body ground
    +B power supply
    Always
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the G35 steering lock ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G35-4 (SLP1) - G35-1 (GND)
    SB - W-B
    Steering lock actuator position signal
    Steering lock locked
    11 to 14 V
    G35-4 (SLP1) - G35-1 (GND)
    SB - W-B
    Steering lock actuator position signal
    Steering lock released
    Below 1 V
    1. If the result is not as specified, the ECU may have a malfunction.

← PROBLEM SYMPTOMS TABLE (from Aug 2014)DIAGNOSIS SYSTEM (from Aug 2013) →