DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2013
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
*1: for Automatic TransmissionPower Source Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Shift P Signal*1
Shift P position signal / ON or OFF
ON: Shift lever in P
OFF: Shift lever not in P
-
Steering Unlock Switch
Steering lock condition / ON or OFF
ON: Steering lock released
(Engine switch on [ACC])
OFF: Steering lock locked
(Engine switch off)
-
Stop Light Switch1*1
Stop light switch 1 / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Start Switch1
Start switch 1 / ON or OFF
ON: Engine switch pushed
OFF: Engine switch not pushed
-
Start Switch2
Start switch 2 / ON or OFF
ON: Engine switch pushed
OFF: Engine switch not pushed
-
Neutral SW/ Clutch SW
Status of park/neutral position switch*1 or clutch start switch*2 / ON or OFF
ON: Park/neutral position switch*1 or clutch start switch*2 on
OFF: Park/neutral position switch*1 or clutch start switch*2 off
-
Latch Circuit
Latch circuit / ON or OFF
ON: Engine switch on (IG) or engine running
OFF: Engine switch off or on (ACC)
-
IG1 Relay Monitor(Outside)
IG1 outer relay monitor / ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
IG1 Relay Monitor(Inside)
IG1 inner relay monitor / ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
IG2 Relay Monitor(Outside)
IG2 outer relay monitor / ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
IG2 Relay Monitor(Inside)
IG2 inner relay monitor / ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
Starter Request Signal
Starter request signal monitor / ON or OFF
ON: ST relay on
OFF: ST relay off
The engine switch is pressed and held with the shift lever in P or N.*1
The engine switch is pressed and held.*2
ACC Relay Monitor
ACC relay monitor / ON or OFF
ON: Engine switch on (ACC)
OFF: Engine switch off
-
Engine Condition
Engine condition / Stop or Run
Stop: Engine stopped
Run: Engine running
-
Vehicle Speed Signal
Vehicle speed signal / Stop or Run
Stop: Vehicle stopped
Run: Vehicle driven (5 km/h (3 mph) or more)
-
Shift P Signal Pulse*1
Status of shift P signal pulse / Unknown, Error2, Normal2, Error1, Normal3, Error3 or Normal1
Unknown: Shift P signal pulse unknown
Error1, Error2 or Error3: Shift P signal pulse abnormal
Normal1, Normal2 or Normal3: Shift P signal pulse normal
-
Power Supply Condition
Power supply condition / IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
IG2 ON: IG2 relay on
ST ON: ST request signal on
All OFF: All relays off
IG1 ON: IG1 relay on
ACC ON: ACC relay on
-
Powertrain Type
Status of powertrain type / HV-AT, Cnv-MT, Cnv-AT, Cnv-MMT
Cnv-AT: Powertrain type automatic transmission*1
Cnv-MT: Powertrain type manual transmission*2
-
IG1 Circuit
Status of IG1 circuit / OK or NG
OK: IG1 circuit OK
NG: IG1 circuit NG
-
IG2 Circuit
Status of IG2 circuit / OK or NG
OK: IG2 circuit OK
NG: IG2 circuit NG
-
Starter SW Sig Mismatch
Starter switch signal mismatch / Yes or No
Yes: Starter switch signal mismatch
No: Starter switch signal match
-
Park Signal Mismatch*1
Park signal mismatch / Yes or No
Yes: Park signal mismatch
No: Park signal match
-
Str Lock/Unlock Wait T-Out
Steering lock/unlock waiting timed out / Yes or No
Yes: Steering lock/unlock waiting timed out
No: Steering lock locks/releases normally within specified time
-
Key Certifi Wait T-Out
Key certification waiting timed out / Yes or No
Yes: Key certification waiting timed out
No: Key certification completed within specified time
-
IG P Status
Status of IG P signal / ON or OFF
ON: IG P signal on
OFF: IG P signal off
-
Number of Diagnosis Code
Number of diagnostic trouble codes / 0 to 255
-
-
*2: for Manual TransmissionEntry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Number of Diagnosis Code
Number of diagnostic trouble codes / 0 to 255
-
-
Power Supply Open
Power supply open / OK or NG(Past)
OK: Power supply normal
NG(Past): Power supply open occurred in past
-
Engine Start Request
Start request signal response / OK or NG
OK: Received
NG: Not received
-
S Code Check
S code certification result / OK or NG
OK: S code certification result normal
NG: S code certification result abnormal
-
L Code Check
L code certification result / OK or NG
OK: L code certification result normal
NG: L code certification result abnormal
-
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display |
Test Part |
Control Range |
Diagnostic Note |
| Indicator Condition |
Engine switch indicator |
Green / Red / No Sig |
Perform this Active Test when the engine switch is off, or while the engine is running. |
| P Supply for Steering Lock |
Power supply for steering lock motor |
ON / OFF |
Perform this Active Test after the engine switch illumination turns off after turning the engine switch off, or while the engine is running. |