2013-2015 Land Cruiser Prado · Service Manual Brake

TC and CG Terminal Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to output the DTCs by blinking the ABS warning light and slip indicator light.

WIRING DIAGRAM

C200425E33

HINT:
When the warning lights continue to blink, a ground short in the wiring of terminal 13 (TC) of the DLC3 or an internal ground short in one or more ECUs is suspected.


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform calibration (Click here).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (for LHD without Entry and Start System: Click here, for RHD without Entry and Start System: Click here).

    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    for LHD without Entry and Start System
    B
    DTC output
    for RHD without Entry and Start System
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2. INSPECT DLC3

  1. C146309E17
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-13 (TC) - G48-4 (CG)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 4
OK


3. INSPECT ECM (DLC3 INPUT)
SST
09843-18040  
  1. Turn the ignition switch off.

  1. C146309E17
    Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
    Text in Illustration 
    *a
    Front view of DLC3

  1. Turn the ignition switch to ON.

  1. Check that the MIL is blinking.

    Result 
    Result
    Proceed to
    MIL is blinking
    A
    MIL is not blinking
    B

    HINT:
    Refer to the ECM installation procedure (for 5L-E: Click here, for 2TR-FE: Click here)



B
REPAIR OR REPLACE WIRE HARNESS OR ECM
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

4. CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
  1. Turn the ignition switch off.

  1. for 5L-E:

    1. Disconnect the G61 ECM connector.

  1. for 2TR-FE:

    1. Disconnect the G60 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 5L-E: 
    Tester Connection
    Condition
    Specified Condition
    G48-13 (TC) - G61-4 (TC)
    Always
    Below 1 Ω
    G48-13 (TC) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FE: 
    Tester Connection
    Condition
    Specified Condition
    G48-13 (TC) - G60-13 (TC)
    Always
    Below 1 Ω
    G48-13 (TC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G48-4 (CG) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT ECM (DLC3 INPUT)
SST
09843-18040  
  1. Turn the ignition switch off.

  1. Connect the ECM connector.

  1. C146309E17
    Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
    Text in Illustration 
    *a
    Front view of DLC3

  1. Turn the ignition switch to ON.

  1. Check that the MIL is blinking.

    Result 
    Result
    Proceed to
    MIL is blinking
    A
    MIL is not blinking
    B



B
REPAIR OR REPLACE WIRE HARNESS OR ECM
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← TC and CG Terminal Circuit (Aug 2013 – Jul 2014)TS and CG Terminal Circuit (Aug 2013 – Jul 2014) →