2013-2015 Land Cruiser Prado · Service Manual Suspension

DATA LIST / ACTIVE TEST

System information · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


READ DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Turn the ignition switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the ignition switch ON.

  4. Turn the GTS on.

  5. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  6. According to the display on the GTS, read the Data List.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mode Status
    Tire pressure warning system mode/
    NORMAL or TEST
    NORMAL: Normal mode
    TEST: Test mode
    -
    Main Tire
    Number of main tire ID to be registered/
    4 or 5
    4 or 5 displayed
    -
    2nd Tire*1
    -
    -
    -
    Vehicle Speed
    Vehicle speed reading/
    min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
    Actual vehicle speed
    Speed indicated on the combination meter assembly
    Registered ID 1 Code
    Registered ID1 code/
    min.: 0, max.: FFFFFFF*2
    ID No. registered for transmitter ID1 displayed
    -
    Registered ID 2 Code
    Registered ID2 code/
    min.: 0, max.: FFFFFFF*2
    ID No. registered for transmitter ID2 displayed
    -
    Registered ID 3 Code
    Registered ID3 code/
    min.: 0, max.: FFFFFFF*2
    ID No. registered for transmitter ID3 displayed
    -
    Registered ID 4 Code
    Registered ID4 code/
    min.: 0, max.: FFFFFFF*2
    ID No. registered for transmitter ID4 displayed
    -
    Registered ID 5 Code*4
    Registered ID5 code/
    min.: 0, max.: FFFFFFF*2
    ID No. registered for transmitter ID5 displayed
    -
    ID Transmission Status
    ID transmission status
    Finish or Now
    Finish or Now
    -
    Initialization Switch
    Tire pressure warning reset switch/
    ON or OFF
    ON: Switch on
    OFF: Switch off
    -
    ID 1 Temperature in Tire
    ID1 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID 2 Temperature in Tire
    ID2 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID 3 Temperature in Tire
    ID3 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID 4 Temperature in Tire
    ID4 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    ID 5 Temperature in Tire*4
    ID5 temperature in tire/
    min.: -40°C (-40°F), max.: 215°C (419°F)
    Actual tire temperature
    If -40°C (-40°F) is displayed, data has not been received.
    Initialization Switch Info
    Tire pressure warning reset switch setting information/
    WITH or WITHOUT
    WITH
    -
    ID 1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*3
    ID 2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*3
    ID 3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*3
    ID 4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*3
    ID 5 Tire Inflation Pressure*4
    ID5 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*3
    ID 1 Initial Threshold of Low-pressure
    ID1 initial threshold of low-pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    Tire pressure after initialization
    -
    ID 2 Initial Threshold of Low-pressure
    ID2 initial threshold of low-pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    Tire pressure after initialization
    -
    ID 3 Initial Threshold of Low-pressure
    ID3 initial threshold of low-pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    Tire pressure after initialization
    -
    ID 4 Initial Threshold of Low-pressure
    ID4 initial threshold of low-pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    Tire pressure after initialization
    -
    ID 5 Initial Threshold of Low-pressure*4
    ID5 initial threshold of low-pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (gauge)/ 380 kPa (3.9 kgf/cm2, 55 psi)
    Tire pressure after initialization
    -
    Number of Trouble Code
    Number of DTCs recorded/
    min.: 0, max.: 255
    0
    -

    HINT:
    1. *1: This item is displayed on the GTS, however, it is not used for this vehicle.
    2. *2: Displayed only when the ID No. is not registered.
    3. *3: It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (C2121/21 to C2125/25: w/ Spare Tire) (Click here).
    4. *4: w/ Spare Tire
    5. The wheel position cannot be determined from ID1 through ID4 or ID1 through ID5 (w/ Spare Tire) on the Data List.


PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows the relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
  1. Turn the ignition switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the ignition switch ON.

  4. Turn the GTS on.

  5. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  6. Check the operation by referring to the table below.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Tire Pressure Warning System
    Tire pressure warning light
    OFF or ON
    Confirm that the vehicle is stopped with the engine idling.

← DTC CHECK / CLEAR (from Aug 2014)DATA LIST / ACTIVE TEST (from Aug 2014) →