2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

Driver Side Door Entry Lock and Unlock Functions do not Operate

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the driver side door entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) the power door lock control system, 2) the front door outside handle assembly (for driver side), or 3) the certification ECU.

WIRING DIAGRAM

B243941E01

INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Check that there are no electrical key transmitters in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
  6. Before replacing the certification ECU, refer to the Service Bulletin.


1. CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. CHECK WAVE ENVIRONMENT
  1. Bring the electrical key transmitter approximately 0.3 m (0.984 ft.) from the door outside handle (for driver side) and perform a driver side door entry lock and unlock operation check (Click here).

    NOTICE:
    If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication is not possible.

    HINT:
    1. When the electrical key transmitter is brought near the driver side door outside handle, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Entry function operates normally.



NG
Go to step 3
OK

AFFECTED BY WAVE INTERFERENCE

3. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Lock Pos*1
    Front RH side door lock position switch signal / UNLOCK or LOCK
    UNLOCK: Front RH side door unlocked
    LOCK: Front RH side door locked
    -
    FL Door Lock Pos*2
    Front LH side door lock position switch signal / UNLOCK or LOCK
    UNLOCK: Front LH side door unlocked
    LOCK: Front LH side door locked
    -
    1. *1: for RHD
    2. *2: for LHD

    OK:
    On the intelligent tester screen, the display changes between LOCK and UNLOCK as shown in the chart above.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Driver Door Lock/Unlock Functions do not Operate) (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
  1. Disconnect the O1*1 or N1*2 handle connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the G38 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    O1-3 (ANT2) - G38-4 (CG1B)
    Always
    Below 1 Ω
    O1-6 (ANT1) - G38-3 (CLG1)
    Always
    Below 1 Ω
    O1-5 (B) - G38-32 (POS1)
    Always
    Below 1 Ω
    O1-2 (GND) - Body ground
    Always
    Below 1 Ω
    G38-4 (CG1B) - Body ground
    Always
    10 kΩ or higher
    G38-3 (CLG1) - Body ground
    Always
    10 kΩ or higher
    G38-32 (POS1) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    N1-3 (ANT2) - G38-4 (CG1B)
    Always
    Below 1 Ω
    N1-6 (ANT1) - G38-3 (CLG1)
    Always
    Below 1 Ω
    N1-5 (B) - G38-32 (POS1)
    Always
    Below 1 Ω
    N1-2 (GND) - Body ground
    Always
    Below 1 Ω
    G38-4 (CG1B) - Body ground
    Always
    10 kΩ or higher
    G38-3 (CLG1) - Body ground
    Always
    10 kΩ or higher
    G38-32 (POS1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK CERTIFICATION ECU (OUTPUT SIGNAL)

  1. B199753E38
    Disconnect the O1*1 or N1*2 handle connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O1-3 (ANT2) - O1-6 (ANT1)
    Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
    No pulse generation → Pulse generation
    O1-5 (B) - Body ground
    Engine switch off → on (IG)
    9 to 14 V → Below 2 V
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N1-3 (ANT2) - N1-6 (ANT1)
    Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
    No pulse generation → Pulse generation
    N1-5 (B) - Body ground
    Engine switch off → on (IG)
    9 to 14 V → Below 2 V

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Front Door Outside Handle Assembly [for Driver Side])



NG
REPLACE CERTIFICATION ECU
OK


6. REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE)
  1. Temporarily replace the front door outside handle assembly (for driver side) with a new or normally functioning one (Click here).


NEXT


7. CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
  1. Check that the entry functions operate normally (Click here).

    OK:
    Entry functions operate normally.



NG
REPLACE CERTIFICATION ECU
OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY IS DEFECTIVE)


← Driver Side Door Entry Lock and Unlock Functions do not Operate (Aug 2013 – Jul 2014)Front Passenger Side Door Entry Lock and Unlock Functions do not Operate (Aug 2013 – Jul 2014) →