Front Passenger Side Door Entry Lock and Unlock Functions do not Operate
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
When the front passenger side door entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) the power door lock control system, 2) the front door outside handle (for front passenger side), or 3) the certification ECU.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
- Check that there are no electrical key transmitters in the vehicle.
- Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
- When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
- Before replacing the certification ECU, refer to the Service Bulletin.
- The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
| 1. CHECK POWER DOOR LOCK OPERATION |
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).
- OK:
- Door locks operate normally.
|
|
||||
| OK | |
| 2. CHECK WAVE ENVIRONMENT |
Bring the electrical key transmitter approximately 0.3 m (0.984 ft.) from the door outside handle (for front passenger side) and perform a front passenger side door entry lock and unlock operation check (Click here).
- NOTICE:
- If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication is not possible.
- HINT:
- When the electrical key transmitter is brought near the front passenger side door outside handle, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
- If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
- When the electrical key transmitter is brought near the front passenger side door outside handle, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
- OK:
- Entry function operates normally.
|
|
||||
| OK | ||
| ||
| 3. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Door Lock Pos*1
Front RH side door lock position switch signal / UNLOCK or LOCK
UNLOCK: Front RH side door unlocked
LOCK: Front RH side door locked
-
FL Door Lock Pos*2
Front LH side door lock position switch signal / UNLOCK or LOCK
UNLOCK: Front LH side door unlocked
LOCK: Front LH side door locked
-
- *1: for LHD
- *2: for RHD
- OK:
- On the intelligent tester screen, the display changes between LOCK and UNLOCK as shown in the chart above.
- *1: for LHD
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU) |
Disconnect the N1*1 or O1*2 handle connector.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Disconnect the G38 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
N1-3 (ANT2) - G38-6 (CG2B)
Always
Below 1 Ω
N1-6 (ANT1) - G38-5 (CLG2)
Always
Below 1 Ω
N1-5 (B) - G38-33 (POS2)
Always
Below 1 Ω
N1-2 (GND) - Body ground
Always
Below 1 Ω
G38-6 (CG2B) - Body ground
Always
10 kΩ or higher
G38-5 (CLG2) - Body ground
Always
10 kΩ or higher
G38-33 (POS2) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
O1-3 (ANT2) - G38-6 (CG2B)
Always
Below 1 Ω
O1-6 (ANT1) - G38-5 (CLG2)
Always
Below 1 Ω
O1-5 (B) - G38-33 (POS2)
Always
Below 1 Ω
O1-2 (GND) - Body ground
Always
Below 1 Ω
G38-6 (CG2B) - Body ground
Always
10 kΩ or higher
G38-5 (CLG2) - Body ground
Always
10 kΩ or higher
G38-33 (POS2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK CERTIFICATION ECU (OUTPUT SIGNAL) |
Disconnect the N1*1 or O1*2 handle connector.

- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
- for LHD:
Tester Connection
Switch Condition
Specified Condition
N1-3 (ANT2) - N1-6 (ANT1)
Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
No pulse generation → Pulse generation
N1-5 (B) - Body ground
Engine switch off → on (IG)
9 to 14 V → Below 2 V
- for RHD:
Tester Connection
Switch Condition
Specified Condition
O1-3 (ANT2) - O1-6 (ANT1)
Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
No pulse generation → Pulse generation
O1-5 (B) - Body ground
Engine switch off → on (IG)
9 to 14 V → Below 2 V
Text in Illustration *A
for LHD
*B
for RHD
*a
Front view of wire harness connector
(to Front Door Outside Handle Assembly [for Front Passenger Side])
|
|
||||
| OK | |
| 6. REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE) |
Temporarily replace the front door outside handle assembly (for front passenger side) with a new or normally functioning one (Click here).
| NEXT | |
| 7. CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION) |
Check that the entry functions operate normally (Click here).
- OK:
- Entry functions operate normally.
|
|
||||
| OK | ||
| ||
