2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

TERMINALS OF ECU

System information · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system (Click here).

    NOTICE:
    1. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the engine switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
    2. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    3. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


JUNCTION CONNECTOR

  1. No. 1 Junction Connector
    C216690E18

    Text in Illustration 
    *a
    for No. 4 Junction Connector
    *b
    for No. 2 Junction Connector (V2 Bus)
    *c
    for Headlight Swivel ECU Assembly (for LED Headlight)
    *d
    for No. 2 Junction Connector (V1 Bus)
    *e
    for Combination Meter Assembly
    *f
    for Master Cylinder Solenoid (Skid Control ECU)
    No. 1 Junction Connector
    Wiring Color
    Connect to
    A72-1 (CANH)
    LG
    No. 4 junction connector
    A72-12 (CANL)
    W
    A72-2 (CANH)
    GR
    No. 2 junction connector (V2 bus)
    A72-13 (CANL)
    W
    A72-3 (CANH)
    V
    Headlight swivel ECU assembly*
    A72-14 (CANL)
    W
    A72-9 (CANH)
    B
    No. 2 junction connector (V1 bus)
    A72-20 (CANL)
    W
    A72-10 (CANH)
    LG
    Combination meter assembly
    A72-21 (CANL)
    W
    A72-11 (CANH)
    R
    Master cylinder solenoid (skid control ECU)
    A72-22 (CANL)
    W
    1. *: for LED Headlight

  2. No. 2 Junction Connector

    1. G132 No. 2 junction connector
      C216690E17

      Text in Illustration 
      *a
      for No. 3 Junction Connector
      *b
      for Main Body ECU (Multiplex Network Body ECU) (V1 Bus)
      *c
      for DLC3
      *d
      for Center Airbag Sensor Assembly
      *e
      for Spiral Cable Sub-assembly (Steering Angle Sensor)
      *f
      for No. 1 Junction Connector
      *g
      1. for Navigation Receiver Assembly (w/ Navigation System [for Navigation Receiver Type])
      2. for Radio and Display Receiver Assembly (w/ Navigation System [for Radio and Display Type] or w/o Navigation System)
      -
      -
      No. 2 Junction Connector
      Wiring Color
      Connect to
      G132-1 (CANH)
      GR
      No. 3 junction connector
      G132-12 (CANL)
      W
      G132-2 (CANH)
      L
      Main body ECU (multiplex network body ECU) (V1 bus)
      G132-13 (CANL)
      W
      G132-4 (CANH)
      R
      DLC3
      G132-15 (CANL)
      W
      G132-5 (CANH)
      Y
      Center airbag sensor assembly
      G132-16 (CANL)
      W
      G132-7 (CANH)
      G
      Spiral cable sub-assembly (steering angle sensor)
      G132-18 (CANL)
      W
      G132-8 (CANH)
      B
      No. 1 junction connector
      G132-19 (CANL)
      W
      G132-9 (CANH)
      P
      1. Navigation receiver assembly*1
      2. Radio and display receiver assembly*2
      G132-20 (CANL)
      W
      1. *1: w/ Navigation System (for Navigation Receiver Type)
      2. *2: w/ Navigation System (for Radio and Display Type) or w/o Navigation System

    2. G95 No. 2 junction connector
      C216690E49

      Text in Illustration 
      *a
      1. for No. 6 Junction Connector (w/ Blind Spot Monitor System)
      2. for No. 3 Junction Connector (w/o Blind Spot Monitor System)
      *b
      for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 4 Sensor Type])
      *c
      for No. 1 Junction Connector
      *d
      for Parking Assist ECU (w/ Side Monitor System)
      *e
      for Stabilizer Control ECU (w/ Kinetic Dynamic Suspension System)
      *f
      for Seat Belt Control ECU (w/ Pre-crash Safety System)
      No. 2 Junction Connector
      Wiring Color
      Connect to
      G95-1 (CANH)
      LG
      1. No. 6 junction connector*1
      2. No. 3 junction connector*2
      G95-12 (CANL)
      W
      G95-2 (CANH)
      R
      Clearance warning ECU assembly*3
      G95-13 (CANL)
      W
      G95-3 (CANH)
      GR
      No. 1 junction connector
      G95-14 (CANL)
      W
      G95-4 (CANH)
      B
      Parking assist ECU*4
      G95-15 (CANL)
      W
      G95-5 (CANH)
      V
      Stabilizer control ECU*5
      G95-16 (CANL)
      W
      G95-6 (CANH)
      L
      Seat belt control ECU*6
      G95-17 (CANL)
      W
      1. *1: w/ Blind Spot Monitor System
      2. *2: w/o Blind Spot Monitor System
      3. *3: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type)
      4. *4: w/ Side Monitor System
      5. *5: w/ Kinetic Dynamic Suspension System
      6. *6: w/ Pre-crash Safety System

    3. G133 No. 2 junction connector
      C216690E28

      Text in Illustration 
      *a
      for Front Power Seat Switch RH (w/ Seat Position Memory)
      *b
      for Multiplex Tilt and Telescopic ECU (for Power Tilt and Power Telescopic Steering Column)
      *c
      for Main Body ECU (Multiplex Network Body ECU) (MS Bus)
      *d
      for Driving Support Switch Control ECU (w/ Multi-function Switch)
      *e
      for No. 5 Junction Connector
      -
      -
      No. 2 Junction Connector
      Wiring Color
      Connect to
      G133-2 (CANH)
      L
      Front power seat switch RH*1
      G133-13 (CANL)
      W
      G133-3 (CANH)
      GR
      Multiplex tilt and telescopic ECU*2
      G133-14 (CANL)
      W
      G133-4 (CANH)
      P
      Main body ECU (multiplex network body ECU) (MS bus)
      G133-15 (CANL)
      W
      G133-5 (CANH)
      R
      Driving support switch control ECU*3
      G133-16 (CANL)
      W
      G133-6 (CANH)
      LG
      No. 5 junction connector
      G133-17 (CANL)
      W
      1. *1: w/ Seat Position Memory
      2. *2: for Power Tilt and Power Telescopic Steering Column
      3. *3: w/ Multi-function Switch

  3. No. 3 Junction Connector

    1. G134 No. 3 junction connector
      C216690E14

      Text in Illustration 
      *a
      for No. 2 Junction Connector
      *b
      for ECM (V1 Bus)
      *c
      for Four Wheel Drive Control ECU
      *d
      for Power Management Control ECU (V1 Bus)
      *e
      for Power Steering ECU Assembly
      *f
      for Certification ECU (Smart Key ECU Assembly)
      *g
      for Yaw Rate Sensor Assembly
      -
      -
      No. 3 Junction Connector
      Wiring Color
      Connect to
      G134-1 (CANH)
      GR
      No. 2 junction connector
      G134-12 (CANL)
      W
      G134-2 (CANH)
      LG
      ECM (V1 bus)
      G134-13 (CANL)
      W
      G134-3 (CANH)
      G
      Four wheel drive control ECU
      G134-14 (CANL)
      W
      G134-4 (CANH)
      BR
      Power management control ECU (V1 bus)
      G134-15 (CANL)
      W
      G134-5 (CANH)
      L
      Power steering ECU assembly
      G134-16 (CANL)
      W
      G134-6 (CANH)
      P
      Certification ECU (smart key ECU assembly)
      G134-17 (CANL)
      W
      G134-8 (CANH)
      R
      Yaw rate sensor assembly
      G134-19 (CANL)
      W

    2. G98 No. 3 junction connector
      C216690E57

      Text in Illustration 
      *a
      1. for No. 6 Junction Connector (w/ Blind Spot Monitor System)
      2. for No. 2 Junction Connector (w/o Blind Spot Monitor System)
      *b
      for Power Management Control ECU (V2 Bus)
      *c
      for Suspension control ECU (w/ Air Suspension System)
      *d
      for Driving Support ECU Assembly (w/ Pre-crash Safety System)
      *e
      for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 8 Sensor Type])
      *f
      for ECM (Power Management Bus)
      *g
      for Air Conditioning Amplifier Assembly
      *h
      for Power Management Control ECU (Power Management Bus)
      No. 3 Junction Connector
      Wiring Color
      Connect to
      G98-1 (CANH)
      B
      1. No. 6 junction connector*1
      2. No. 2 junction connector*2
      G98-12 (CANL)
      W
      G98-2 (CANH)
      V
      Power management control ECU (V2 bus)
      G98-13 (CANL)
      W
      G98-3 (CANH)
      R
      Suspension control ECU*3
      G98-14 (CANL)
      W
      G98-4 (CANH)
      G
      Driving support ECU assembly*4
      G98-15 (CANL)
      W
      G98-5 (CANH)
      R
      Clearance warning ECU assembly*5
      G98-16 (CANL)
      W
      G98-9 (CANH)
      BR
      ECM (power management bus)
      G98-20 (CANL)
      GR
      G98-10 (CANH)
      BR
      Air conditioning amplifier assembly
      G98-21 (CANL)
      Y
      G98-11 (CANH)
      BR
      Power management control ECU (power management bus)
      G98-22 (CANL)
      W
      1. *1: w/ Blind Spot Monitor System
      2. *2: w/o Blind Spot Monitor System
      3. *3: w/ Air Suspension System
      4. *4: w/ Pre-crash Safety System
      5. *5: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type)

  4. C210060E13
    No. 4 Junction Connector
    Text in Illustration 
    *a
    for No. 1 Junction Connector
    No. 4 Junction Connector
    Wiring Color
    Connect to
    G102-2 (CANL)
    W
    No. 1 junction connector
    G102-3 (CANH)
    LG

  5. C210060E14
    No. 5 Junction Connector
    Text in Illustration 
    *a
    for No. 2 Junction Connector
    No. 5 Junction Connector
    Wiring Color
    Connect to
    G103-2 (CANN)
    W
    No. 2 junction connector
    G103-3 (CANP)
    LG

  6. NO. 6 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)
    C216690E47

    Text in Illustration 
    *a
    for No. 2 Junction Connector
    *b
    for Blind Spot Monitor Sensor LH
    *c
    for No. 3 Junction Connector
    -
    -
    No. 6 Junction Connector
    Wiring Color
    Connect to
    R47-1 (CANH)
    LG
    No. 2 junction connector
    R47-12 (CANL)
    W
    R47-2 (CANH)
    G
    Blind spot monitor sensor LH
    R47-13 (CANL)
    W
    R47-3 (CANH)
    B
    No. 3 junction connector
    R47-14 (CANL)
    W


CHECK DLC3
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. H102621E67
    Measure the resistance according to the value(s) in the table below.
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G48-6 (CANH) - G48-14 (CANL)
    R - W
    Engine switch off
    54 to 69 Ω
    G48-6 (CANH) - G48-4 (CG)
    R - W-B
    Engine switch off
    200 Ω or higher
    G48-14 (CANL) - G48-4 (CG)
    W - W-B
    Engine switch off
    200 Ω or higher
    G48-6 (CANH) - G48-16 (BAT)
    R - GR
    Engine switch off
    6 kΩ or higher
    G48-14 (CANL) - G48-16 (BAT)
    W - GR
    Engine switch off
    6 kΩ or higher


CHECK ECM (for 1GR-FE)
C216694E22
Text in Illustration 
*A
for V1 Bus
*B
for Power Management Bus
  1. Disconnect the C36, G55 and G56 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    for V1 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G56-32 (CANH) - G56-31 (CANL)
    LG - W
    Engine switch off
    108 to 132 Ω
    G56-32 (CANH) - C36-12 (E1)
    LG - BR
    Engine switch off
    200 Ω or higher
    G56-31 (CANL) - C36-12 (E1)
    W - BR
    Engine switch off
    200 Ω or higher
    G56-32 (CANH) - G55-24 (BATT)
    LG - L
    Engine switch off
    6 kΩ or higher
    G56-31 (CANL) - G55-24 (BATT)
    W - L
    Engine switch off
    6 kΩ or higher
    for Power Management Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G56-34 (CANP) - G56-33 (CANN)
    BR - GR
    Engine switch off
    108 to 132 Ω
    G56-34 (CANP) - C36-12 (E1)
    BR - BR
    Engine switch off
    200 Ω or higher
    G56-33 (CANN) - C36-12 (E1)
    GR - BR
    Engine switch off
    200 Ω or higher
    G56-34 (CANP) - G55-24 (BATT)
    BR - L
    Engine switch off
    6 kΩ or higher
    G56-33 (CANN) - G55-24 (BATT)
    GR - L
    Engine switch off
    6 kΩ or higher


CHECK ECM (for 1KD-FTV)
C216694E24
Text in Illustration 
*A
for V1 Bus
*B
for Power Management Bus
*C
for Powertrain Bus
-
-
  1. Disconnect the C92, C93, G57 and G58 ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    for V1 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G58-35 (CANH) - G58-36 (CANL)
    LG - W
    Engine switch off
    108 to 132 Ω
    G58-35 (CANH) - C93-1 (E1)
    LG - BR
    Engine switch off
    200 Ω or higher
    G58-36 (CANL) - C93-1 (E1)
    W - BR
    Engine switch off
    200 Ω or higher
    G58-35 (CANH) - G57-23 (BATT)
    LG - L
    Engine switch off
    6 kΩ or higher
    G58-36 (CANL) - G57-23 (BATT)
    W - L
    Engine switch off
    6 kΩ or higher
    for Power Management Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G57-20 (CANP) - G57-21 (CANN)
    BR - GR
    Engine switch off
    108 to 132 Ω
    G57-20 (CANP) - C93-1 (E1)
    BR - BR
    Engine switch off
    200 Ω or higher
    G57-21 (CANN) - C93-1 (E1)
    GR - BR
    Engine switch off
    200 Ω or higher
    G57-20 (CANP) - G57-23 (BATT)
    BR - L
    Engine switch off
    6 kΩ or higher
    G57-21 (CANN) - G57-23 (BATT)
    GR - L
    Engine switch off
    6 kΩ or higher
    for Powertrain Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    C92-24 (CAN+) - C92-18 (CAN-)
    B - W
    Engine switch off
    108 to 132 Ω
    C92-24 (CAN+) - C93-1 (E1)
    B - BR
    Engine switch off
    200 Ω or higher
    C92-18 (CAN-) - C93-1 (E1)
    W - BR
    Engine switch off
    200 Ω or higher
    C92-24 (CAN+) - G57-23 (BATT)
    B - L
    Engine switch off
    6 kΩ or higher
    C92-18 (CAN-) - G57-23 (BATT)
    W - L
    Engine switch off
    6 kΩ or higher


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
B238680E28
Text in Illustration 
*A
for V1 Bus
*B
for MS Bus
*1
Main Body ECU (Multiplex Network Body ECU)
-
-
  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  2. Measure the resistance according to the value(s) in the table below.

    for V1 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G64-14 (CANH) - G64-13 (CANL)
    L - W
    Engine switch off
    54 to 69 Ω
    G64-14 (CANH) - A-11 (GND1)
    L - None
    Engine switch off
    200 Ω or higher
    G64-13 (CANL) - A-11 (GND1)
    W - None
    Engine switch off
    200 Ω or higher
    G64-14 (CANH) - A-30 (BECU)
    L - None
    Engine switch off
    6 kΩ or higher
    G64-13 (CANL) - A-30 (BECU)
    W - None
    Engine switch off
    6 kΩ or higher
    for MS Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G63-9 (CANP) - G63-10 (CANN)
    P - W
    Engine switch off
    108 to 132 Ω
    G63-9 (CANP) - A-11 (GND1)
    P - None
    Engine switch off
    200 Ω or higher
    G63-10 (CANN) - A-11 (GND1)
    W - None
    Engine switch off
    200 Ω or higher
    G63-9 (CANP) - A-30 (BECU)
    P - None
    Engine switch off
    6 kΩ or higher
    G63-10 (CANN) - A-30 (BECU)
    W - None
    Engine switch off
    6 kΩ or higher


CHECK COMBINATION METER ASSEMBLY
E161130E28
  1. Disconnect the G6 combination meter assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G6-40 (CANH) - G6-39 (CANL)
    LG - W
    Engine switch off
    108 to 132 Ω
    G6-40 (CANH) - G6-21 (E2)
    LG - BR
    Engine switch off
    200 Ω or higher
    G6-39 (CANL) - G6-21 (E2)
    W - BR
    Engine switch off
    200 Ω or higher
    G6-40 (CANH) - G6-26 (B)
    LG - L
    Engine switch off
    6 kΩ or higher
    G6-39 (CANL) - G6-26 (B)
    W - L
    Engine switch off
    6 kΩ or higher


CHECK POWER STEERING ECU ASSEMBLY
C217238E04
  1. Disconnect the G46 power steering ECU assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G46-1 (CANH) - G46-2 (CANL)
    L - W
    Engine switch off
    54 to 69 Ω
    G46-1 (CANH) - G46-3 (GND)
    L - W-B
    Engine switch off
    200 Ω or higher
    G46-2 (CANL) - G46-3 (GND)
    W - W-B
    Engine switch off
    200 Ω or higher
    G46-1 (CANH) - G48-16 (BAT)
    L - GR
    Engine switch off
    6 kΩ or higher
    G46-2 (CANL) - G48-16 (BAT)
    W - GR
    Engine switch off
    6 kΩ or higher


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
C215955E01
  1. Disconnect the G25 air conditioning amplifier assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Condition
    Specified Condition
    G25-11 (CANH) - G25-12 (CANL)
    BR - Y
    Engine switch off
    54 to 69 Ω
    G25-11 (CANH) - G25-14 (GND)
    BR - W-B
    Engine switch off
    200 Ω or higher
    G25-12 (CANL) - G25-14 (GND)
    Y - W-B
    Engine switch off
    200 Ω or higher
    G25-11 (CANH) - G25-21 (B)
    BR - V
    Engine switch off
    6 kΩ or higher
    G25-12 (CANL) - G25-21 (B)
    Y - V
    Engine switch off
    6 kΩ or higher


CHECK CENTER AIRBAG SENSOR ASSEMBLY
C208720E07
  1. Disconnect the G1 center airbag sensor assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G1-13 (CANH) - G1-22 (CANL)
    Y - W
    Engine switch off
    54 to 69 Ω
    G1-13 (CANH) - G1-25 (E1)
    Y - W-B
    Engine switch off
    200 Ω or higher
    G1-22 (CANL) - G1-25 (E1)
    W - W-B
    Engine switch off
    200 Ω or higher
    G1-13 (CANH) - G48-16 (BAT)
    Y - GR
    Engine switch off
    6 kΩ or higher
    G1-22 (CANL) - G48-16 (BAT)
    W - GR
    Engine switch off
    6 kΩ or higher


CHECK MASTER CYLINDER SOLENOID (SKID CONTROL ECU)
C215260E02
  1. Disconnect the A7 master cylinder solenoid (skid control ECU) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A7-11 (CANH) - A7-25 (CANL)
    R - W
    Engine switch off
    54 to 69 Ω
    A7-11 (CANH) - A7-1 (GND1)
    R - W-B
    Engine switch off
    200 Ω or higher
    A7-25 (CANL) - A7-1 (GND1)
    W - W-B
    Engine switch off
    200 Ω or higher
    A7-11 (CANH) - A7-2 (+BM1)
    R - B
    Engine switch off
    6 kΩ or higher
    A7-25 (CANL) - A7-2 (+BM1)
    W - B
    Engine switch off
    6 kΩ or higher


CHECK SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)
C201866E04
  1. Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G33-4 (CANH) - G33-3 (CANL)
    G - W
    Engine switch off
    54 to 69 Ω
    G33-4 (CANH) - G33-2 (ESS)
    G - W-B
    Engine switch off
    200 Ω or higher
    G33-3 (CANL) - G33-2 (ESS)
    W - W-B
    Engine switch off
    200 Ω or higher
    G33-4 (CANH) - G33-6 (BAT)
    G - L
    Engine switch off
    6 kΩ or higher
    G33-3 (CANL) - G33-6 (BAT)
    W - L
    Engine switch off
    6 kΩ or higher


CHECK YAW RATE SENSOR ASSEMBLY
C213562E03
  1. Disconnect the G52 yaw rate sensor assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G52-3 (CANH) - G52-2 (CANL)
    R - W
    Engine switch off
    54 to 69 Ω
    G52-3 (CANH) - G52-1 (GND)
    R - W-B
    Engine switch off
    200 Ω or higher
    G52-2 (CANL) - G52-1 (GND)
    W - W-B
    Engine switch off
    200 Ω or higher
    G52-3 (CANH) - G48-16 (BAT)
    R - GR
    Engine switch off
    6 kΩ or higher
    G52-2 (CANL) - G48-16 (BAT)
    W - GR
    Engine switch off
    6 kΩ or higher


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B197893E15
  1. Disconnect the G38 certification ECU (smart key ECU assembly) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G38-9 (CANH) - G38-10 (CANL)
    P - W
    Engine switch off
    54 to 69 Ω
    G38-9 (CANH) - G38-15 (E)
    P - W-B
    Engine switch off
    200 Ω or higher
    G38-10 (CANL) - G38-15 (E)
    W - W-B
    Engine switch off
    200 Ω or higher
    G38-9 (CANH) - G38-1 (+B)
    P - V
    Engine switch off
    6 kΩ or higher
    G38-10 (CANL) - G38-1 (+B)
    W - V
    Engine switch off
    6 kΩ or higher


CHECK POWER MANAGEMENT CONTROL ECU
C201247E07
Text in Illustration 
*A
for V1 Bus
*B
for Power Management Bus
*C
for V2 Bus
-
-
  1. Disconnect the G51 power management control ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    for V1 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G51-14 (CA1H) - G51-13 (CA1L)
    BR - W
    Engine switch off
    54 to 69 Ω
    G51-14 (CA1H) - G51-6 (GND)
    BR - W-B
    Engine switch off
    200 Ω or higher
    G51-13 (CA1L) - G51-6 (GND)
    W - W-B
    Engine switch off
    200 Ω or higher
    G51-14 (CA1H) - G51-1 (AM22)
    BR - B
    Engine switch off
    6 kΩ or higher
    G51-13 (CA1L) - G51-1 (AM22)
    W - B
    Engine switch off
    6 kΩ or higher
    for V2 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G51-26 (CA2H) - G51-25 (CA2L)
    V - W
    Engine switch off
    108 to 132 Ω
    G51-26 (CA2H) - G51-6 (GND)
    V - W-B
    Engine switch off
    200 Ω or higher
    G51-25 (CA2L) - G51-6 (GND)
    W - W-B
    Engine switch off
    200 Ω or higher
    G51-26 (CA2H) - G51-1 (AM22)
    V - B
    Engine switch off
    6 kΩ or higher
    G51-25 (CA2L) - G51-1 (AM22)
    W - B
    Engine switch off
    6 kΩ or higher
    for Power Management Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G51-12 (CA3P) - G51-11 (CA3N)
    BR - W
    Engine switch off
    108 to 132 Ω
    G51-12 (CA3P) - G51-6 (GND)
    BR - W-B
    Engine switch off
    200 Ω or higher
    G51-11 (CA3N) - G51-6 (GND)
    W - W-B
    Engine switch off
    200 Ω or higher
    G51-12 (CA3P) - G51-1 (AM22)
    BR - B
    Engine switch off
    6 kΩ or higher
    G51-11 (CA3N) - G51-1 (AM22)
    W - B
    Engine switch off
    6 kΩ or higher


CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System [for Navigation Receiver Type])
E284973E02
  1. Disconnect the H54 and H56 navigation receiver assembly connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H56-9 (CANH) - H56-10 (CANL)
    W - P
    Engine switch off
    54 to 69 Ω
    H56-9 (CANH) - H54-7 (GND1)
    W - BR
    Engine switch off
    200 Ω or higher
    H56-10 (CANL) - H54-7 (GND1)
    P - BR
    Engine switch off
    200 Ω or higher
    H56-9 (CANH) - H54-4 (+B1)
    W - R
    Engine switch off
    6 kΩ or higher
    H56-10 (CANL) - H54-4 (+B1)
    P - R
    Engine switch off
    6 kΩ or higher


CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Navigation System [for Radio and Display Type] or w/o Navigation System)
E278781E02
  1. Disconnect the H49 and H51 radio and display receiver assembly connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H51-9 (CANH) - H51-10 (CANL)
    W - P
    Engine switch off
    54 to 69 Ω
    H51-9 (CANH) - H49-7 (GND1)
    W - BR
    Engine switch off
    200 Ω or higher
    H51-10 (CANL) - H49-7 (GND1)
    P - BR
    Engine switch off
    200 Ω or higher
    H51-9 (CANH) - H49-4 (+B1)
    W - R
    Engine switch off
    6 kΩ or higher
    H51-10 (CANL) - H49-4 (+B1)
    P - R
    Engine switch off
    6 kΩ or higher


CHECK FOUR WHEEL DRIVE CONTROL ECU
C213564E03
  1. Disconnect the G53 and G54 four wheel drive control ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G53-19 (CANH) - G53-20 (CANL)
    G - W
    Engine switch off
    54 to 69 Ω
    G53-19 (CANH) - G54-4 (GND)
    G - W-B
    Engine switch off
    200 Ω or higher
    G53-20 (CANL) - G54-4 (GND)
    W - W-B
    Engine switch off
    200 Ω or higher
    G53-19 (CANH) - G48-16 (BAT)
    G - GR
    Engine switch off
    6 kΩ or higher
    G53-20 (CANL) - G48-16 (BAT)
    W - GR
    Engine switch off
    6 kΩ or higher


CHECK SUSPENSION CONTROL ECU (w/ Air Suspension System)
G028232E01
  1. Disconnect the A49 suspension control ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A49-7 (CANH) - A49-8 (CANL)
    R - W
    Engine switch off
    54 to 69 Ω
    A49-7 (CANH) - A49-5 (GND)
    R - W-B
    Engine switch off
    200 Ω or higher
    A49-8 (CANL) - A49-5 (GND)
    W - W-B
    Engine switch off
    200 Ω or higher
    A49-7 (CANH) - A49-3 (B)
    R - GR
    Engine switch off
    6 kΩ or higher
    A49-8 (CANL) - A49-3 (B)
    W - GR
    Engine switch off
    6 kΩ or higher


CHECK STABILIZER CONTROL ECU (w/ Kinetic Dynamic Suspension System)
C214235E03
  1. Disconnect the G123 stabilizer control ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G123-29 (CANH) - G123-28 (CANL)
    V - W
    Engine switch off
    54 to 69 Ω
    G123-29 (CANH) - G123-22 (GND)
    V - W-B
    Engine switch off
    200 Ω or higher
    G123-28 (CANL) - G123-22 (GND)
    W - W-B
    Engine switch off
    200 Ω or higher
    G123-29 (CANH) - G48-16 (BAT)
    V - GR
    Engine switch off
    6 kΩ or higher
    G123-28 (CANL) - G48-16 (BAT)
    W - GR
    Engine switch off
    6 kΩ or higher


CHECK SEAT BELT CONTROL ECU (w/ Pre-crash Safety System)
E140518E29
  1. Disconnect the G117 and G118 seat belt control ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G118-1 (CANH) - G118-2 (CANL)
    L - W
    Engine switch off
    54 to 69 Ω
    G118-1 (CANH) - G117-8 (PGND)
    L - W-B
    Engine switch off
    200 Ω or higher
    G118-2 (CANL) - G117-8 (PGND)
    W - W-B
    Engine switch off
    200 Ω or higher
    G118-1 (CANH) - G117-7 (+B)
    L - W
    Engine switch off
    6 kΩ or higher
    G118-2 (CANL) - G117-7 (+B)
    W - W
    Engine switch off
    6 kΩ or higher


CHECK DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)
C220129E07
Text in Illustration 
*A
for V2 Bus
*B
for Parking Assist Bus

NOTICE:
  1. As disconnecting the connector to perform inspections may cause DTCs to be stored, clear DTCs after performing inspections.
  2. As the connector may be damaged if a load of more than 10 kg (22 lb) is applied to it, do not apply any more load than necessary to the connector.

  1. Disconnect the G119 driving support ECU assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    for V2 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G119-39 (CA2H) - G119-17 (CA2L)
    G - W
    Engine switch off
    54 to 69 Ω
    G119-39 (CA2H) - G119-25 (GND)
    G - BR
    Engine switch off
    200 Ω or higher
    G119-17 (CA2L) - G119-25 (GND)
    W - BR
    Engine switch off
    200 Ω or higher
    G119-39 (CA2H) - G119-30 (B)
    G - G
    Engine switch off
    6 kΩ or higher
    G119-17 (CA2L) - G119-30 (B)
    W - G
    Engine switch off
    6 kΩ or higher
    for Parking Assist Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G119-40 (CA1P) - G119-18 (CA1N)
    L - P
    Engine switch off
    108 to 132 Ω
    G119-40 (CA1P) - G119-25 (GND)
    L - BR
    Engine switch off
    200 Ω or higher
    G119-18 (CA1N) - G119-25 (GND)
    P - BR
    Engine switch off
    200 Ω or higher
    G119-40 (CA1P) - G48-16 (BAT)
    L - GR
    Engine switch off
    6 kΩ or higher
    G119-18 (CA1N) - G48-16 (BAT)
    P - GR
    Engine switch off
    6 kΩ or higher


CHECK PARKING ASSIST ECU (w/ Side Monitor System)
C288325E02
  1. Disconnect the I6 and I7 parking assist ECU connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    I7-40 (CANH) - I7-39 (CANL)
    B - W
    Engine switch off
    54 to 69 Ω
    I7-40 (CANH) - I6-4 (GND1)
    B - W-B
    Engine switch off
    200 Ω or higher
    I7-39 (CANL) - I6-4 (GND1)
    W - W-B
    Engine switch off
    200 Ω or higher
    I7-40 (CANH) - I6-1 (+B)
    B - L
    Engine switch off
    6 kΩ or higher
    I7-39 (CANL) - I6-1 (+B)
    W - L
    Engine switch off
    6 kΩ or higher


CHECK CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)

  1. for 4 Sensor Type:
    C217402E01

    1. Disconnect the I1 clearance warning ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Switch Condition
      Specified Condition
      I1-3 (R1) - I1-5 (R2)
      R - W
      Engine switch off
      54 to 69 Ω
      I1-3 (R1) - I1-17 (E)
      R - W-B
      Engine switch off
      200 Ω or higher
      I1-5 (R2) - I1-17 (E)
      W - W-B
      Engine switch off
      200 Ω or higher
      I1-3 (R1) - G48-16 (BAT)
      R - GR
      Engine switch off
      6 kΩ or higher
      I1-5 (R2) - G48-16 (BAT)
      W - GR
      Engine switch off
      6 kΩ or higher

  2. for 8 Sensor Type:
    C217402E09

    1. Disconnect the G154 clearance warning ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Switch Condition
      Specified Condition
      G154-3 (R1) - G154-5 (R2)
      R - W
      Engine switch off
      54 to 69 Ω
      G154-3 (R1) - G154-17 (E)
      R - W-B
      Engine switch off
      200 Ω or higher
      G154-5 (R2) - G154-17 (E)
      W - W-B
      Engine switch off
      200 Ω or higher
      G154-3 (R1) - G48-16 (BAT)
      R - GR
      Engine switch off
      6 kΩ or higher
      G154-5 (R2) - G48-16 (BAT)
      W - GR
      Engine switch off
      6 kΩ or higher


CHECK HEADLIGHT SWIVEL ECU ASSEMBLY (for LED Headlight)
C217403E01
  1. Disconnect the A58 headlight swivel ECU assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A58-12 (CANH) - A58-13 (CANL)
    V - W
    Engine switch off
    54 to 69 Ω
    A58-12 (CANH) - A58-22 (E1)
    V - W-B
    Engine switch off
    200 Ω or higher
    A58-13 (CANL) - A58-22 (E1)
    W - W-B
    Engine switch off
    200 Ω or higher
    A58-12 (CANH) - G48-16 (BAT)
    V - GR
    Engine switch off
    6 kΩ or higher
    A58-13 (CANL) - G48-16 (BAT)
    W - GR
    Engine switch off
    6 kΩ or higher


CHECK MULTIPLEX TILT AND TELESCOPIC ECU (for Power Tilt and Power Telescopic Steering Column)
C215995E01
  1. Disconnect the G116 multiplex tilt and telescopic ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G116-5 (CANP) - G116-14 (CANN)
    GR - W
    Engine switch off
    54 to 69 Ω
    G116-5 (CANP) - G116-11 (GND)
    GR - W-B
    Engine switch off
    200 Ω or higher
    G116-14 (CANN) - G116-11 (GND)
    W - W-B
    Engine switch off
    200 Ω or higher
    G116-5 (CANP) - G116-2 (+B)
    GR - G
    Engine switch off
    6 kΩ or higher
    G116-14 (CANN) - G116-2 (+B)
    W - G
    Engine switch off
    6 kΩ or higher


CHECK FRONT POWER SEAT SWITCH RH (w/ Seat Position Memory)
B219506E51
  1. Disconnect the a4 and a5 front power seat switch RH connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    a5-8 (CANP) - a5-7 (CANN)
    L - W
    Engine switch off
    54 to 69 Ω
    a5-8 (CANP) - a4-2 (GND)
    L - W-B
    Engine switch off
    200 Ω or higher
    a5-7 (CANN) - a4-2 (GND)
    W - W-B
    Engine switch off
    200 Ω or higher
    a5-8 (CANP) - a4-7 (+B)
    L - W
    Engine switch off
    6 kΩ or higher
    a5-7 (CANN) - a4-7 (+B)
    W - W
    Engine switch off
    6 kΩ or higher


CHECK DRIVING SUPPORT SWITCH CONTROL ECU (w/ Multi-function Switch)

  1. for Automatic Transmission:
    C288327E02

    1. Disconnect the G163 driving support switch control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Switch Condition
      Specified Condition
      G163-2 (CANP) - G163-3 (CANN)
      R - W
      Engine switch off
      54 to 69 Ω
      G163-2 (CANP) - G163-7 (GND)
      R - W-B
      Engine switch off
      200 Ω or higher
      G163-3 (CANN) - G163-7 (GND)
      W - W-B
      Engine switch off
      200 Ω or higher
      G163-2 (CANP) - G163-8 (+B)
      R - L
      Engine switch off
      6 kΩ or higher
      G163-3 (CANN) - G163-8 (+B)
      W - L
      Engine switch off
      6 kΩ or higher

  2. for Manual Transmission:
    E194339E07

    1. Disconnect the G76 driving support switch control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol)
      Wiring Color
      Switch Condition
      Specified Condition
      G76-9 (CANP) - G76-10 (CANN)
      R - W
      Engine switch off
      54 to 69 Ω
      G76-9 (CANP) - G76-16 (GND)
      R - W-B
      Engine switch off
      200 Ω or higher
      G76-10 (CANN) - G76-16 (GND)
      W - W-B
      Engine switch off
      200 Ω or higher
      G76-9 (CANP) - G76-6 (+B)
      R - L
      Engine switch off
      6 kΩ or higher
      G76-10 (CANN) - G76-6 (+B)
      W - L
      Engine switch off
      6 kΩ or higher


CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor Sensor)
C270134E17
Text in Illustration 
*A
for V2 Bus
*B
for Sensor Bus
  1. Disconnect the R42 blind spot monitor sensor LH connector.

  2. Measure the resistance according to the value(s) in the table below.

    for V2 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    R42-2 (CA1P) - R42-7 (CA1N)
    G - W
    Engine switch off
    54 to 69 Ω
    R42-2 (CA1P) - R42-10 (BLGD)
    G - W-B
    Engine switch off
    200 Ω or higher
    R42-7 (CA1N) - R42-10 (BLGD)
    W - W-B
    Engine switch off
    200 Ω or higher
    R42-2 (CA1P) - G48-16 (BAT)
    G - GR
    Engine switch off
    6 kΩ or higher
    R42-7 (CA1N) - G48-16 (BAT)
    W - GR
    Engine switch off
    6 kΩ or higher
    for Sensor Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    R42-1 (CA2P) - R42-6 (CA2N)
    V - W
    Engine switch off
    108 to 132 Ω
    R42-1 (CA2P) - R42-10 (BLGD)
    V - W-B
    Engine switch off
    200 Ω or higher
    R42-6 (CA2N) - R42-10 (BLGD)
    W - W-B
    Engine switch off
    200 Ω or higher
    R42-1 (CA2P) - G48-16 (BAT)
    V - GR
    Engine switch off
    6 kΩ or higher
    R42-6 (CA2N) - G48-16 (BAT)
    W - GR
    Engine switch off
    6 kΩ or higher


CHECK BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor Sensor)
C270134E18
  1. Disconnect the R43 blind spot monitor sensor RH connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    R43-1 (CA2P) - R43-6 (CA2N)
    V - W
    Engine switch off
    108 to 132 Ω
    R43-1 (CA2P) - R43-10 (BRGD)
    V - W-B
    Engine switch off
    200 Ω or higher
    R43-6 (CA2N) - R43-10 (BRGD)
    W - W-B
    Engine switch off
    200 Ω or higher
    R43-1 (CA2P) - G48-16 (BAT)
    V - GR
    Engine switch off
    6 kΩ or higher
    R43-6 (CA2N) - G48-16 (BAT)
    W - GR
    Engine switch off
    6 kΩ or higher


CHECK TRANSMISSION CONTROL ECU ASSEMBLY (for 1KD-FTV and Automatic Transmission System)
C214981E16
  1. Disconnect the G69 and G70 transmission control ECU assembly connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    G70-21 (CAN+) - G70-20 (CAN-)
    B - W
    Engine switch off
    108 to 132 Ω
    G70-21 (CAN+) - G69-1 (E1)
    B - BR
    Engine switch off
    200 Ω or higher
    G70-20 (CAN-) - G69-1 (E1)
    W - BR
    Engine switch off
    200 Ω or higher
    G70-21 (CAN+) - G70-5 (BATT)
    B - L
    Engine switch off
    6 kΩ or higher
    G70-20 (CAN-) - G70-5 (BATT)
    W - L
    Engine switch off
    6 kΩ or higher


CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)
C207482E05
  1. Disconnect the A15 millimeter wave radar sensor assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A15-4 (CA1P) - A15-3 (CA1N)
    L - W
    Engine switch off
    108 to 132 Ω
    A15-4 (CA1P) - A15-3 (CA1N)
    L - BR
    Engine switch off
    200 Ω or higher
    A15-4 (CA1P) - A15-3 (CA1N)
    W - BR
    Engine switch off
    200 Ω or higher
    A15-4 (CA1P) - A15-3 (CA1N)
    L - GR
    Engine switch off
    6 kΩ or higher
    A15-3 (CA1N) - G48-16 (BAT)
    W - GR
    Engine switch off
    6 kΩ or higher

← TERMINALS OF ECU (Aug 2013 – Jul 2014)DIAGNOSIS SYSTEM (Aug 2013 – Jul 2014) →