2013-2015 Land Cruiser Prado · Service Manual General

INITIALIZATION

Troubleshooting · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


PROCEDURES NECESSARY WHEN CABLE IS DISCONNECTED/RECONNECTED TO BATTERY TERMINAL
Procedures Necessary when Cable is Disconnected/Reconnected to Battery Terminal 
Necessary Procedure
Effect or Inoperative Function when Necessary Procedure is not Performed
See page
Correction of steering angle neutral point
Calibration
for Vehicle stability control system (for Hydraulic Brake Booster) Click here
for Parking assist monitor system (w/ Side Monitor System) Click here
for Parking assist monitor system (w/o Side Monitor System) Click here

NOTICE:
  1. After the battery is reconnected, be sure to wait 10 seconds or more before attempting to start the engine. The engine may not start immediately after the battery is reconnected.
  2. w/ Navigation System:
    After the engine switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the engine switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
Procedures Necessary when ECU or Other Parts are Replaced 
Replacement Part
Necessary Procedure
Effect or Inoperative Function when Necessary Procedure is not Performed
See Page
ECM (for 2TR-FE)
Register VIN
DTC P0630 is input
Click here
  1. ECM (for 2TR-FE)
  2. Throttle body with motor assembly (for 2TR-FE)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
  1. ECM (for 1GR-FE)
  2. Throttle body with motor assembly (for 1GR-FE)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
ECM (for 1KD-FTV, w/ DPF)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
Crankshaft position sensor plate (for 1KD-FTV, w/ DPF)
Clear crank time compensation data
Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data
A/F sensor (for 1KD-FTV, w/ DPF)
Clear A/F sensor compensation data
EGR volume is affected
Fuel supply pump (for 1KD-FTV, w/ DPF)
Supply pump initialization
Engine startability is affected
DPF catalyst (for 1KD-FTV, w/ DPF)
Clear DPF thermal deterioration data
Even if catalytic converter is replaced with new one, catalyst record of DPF thermal deterioration stored in ECM is same as before replacement
Fuel injector (for 1KD-FTV, w/ DPF)
  1. Injector compensation code registration
  2. Pilot quantity learning
Injector fuel injection compensation amount is same as before replacement, affecting injector fuel injection volume
ECM (for 1KD-FTV, w/o DPF)
  1. Learning values save
  2. Learning values write
Engine starting
Click here
Crankshaft position sensor plate (for 1KD-FTV, w/o DPF)
Clear crank time compensation data
Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data
Fuel supply pump (for 1KD-FTV, w/o DPF)
Supply pump initialization
Engine startability is affected
Fuel injector (for 1KD-FTV, w/o DPF)
  1. Injector compensation code registration
  2. Pilot quantity learning
Injector fuel injection compensation amount is same as before replacement, affecting injector fuel injection volume
  1. ECM
  2. Driving support ECU
Initialization
Dynamic radar cruise control system
Click here
Millimeter wave radar sensor assembly
Adjust millimeter wave radar sensor assembly (Dynamic radar cruise control system)
  1. Dynamic radar cruise control system
  2. Pre-crash safety system
Click here
  1. Automatic transmission assembly (for 1KD-FTV)
  2. Valve body assembly (for 1KD-FTV)
  3. Any of the shift solenoid valve (for 1KD-FTV)
Reset memory
Large shift shock
Click here
  1. Automatic transmission assembly (for 1GR-FE)
  2. Valve body assembly (for 1GR-FE)
  3. Any of the shift solenoid valve (for 1GR-FE)
Reset memory
Large shift shock
Click here
Automatic transmission fluid (for A750F, for 1GR-FE)
ATF thermal degradation estimate reset
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.
Click here
Tire pressure warning ECU and receiver
  1. Register transmitter IDs
  2. Initialize tire pressure warning system
  1. When DTC detection conditions of "transmitter ID not received" DTC is met, tire pressure warning light blinks for 1 minute, and then illuminates
  2. Tire pressure monitoring function
Click here(for Registration)
Click here(for Initialization)
Suspension control ECU
Registration
Air suspension system
Click here
  1. Brake actuator assembly
  2. Acceleration sensor
Calibration
Anti-lock brake system
Click here
  1. Master cylinder solenoid (Skid control ECU)
  2. Yaw rate and acceleration sensor
  3. Spiral cable sub-assembly (steering angle sensor)
Calibration
Vehicle stability control system (for Hydraulic Brake Booster)
Click here
  1. Brake actuator assembly (Skid control ECU)
  2. Yaw rate and acceleration sensor
  3. Spiral cable sub-assembly (steering angle sensor)
Calibration
Vehicle stability control system (for Vacuum Brake Booster)
Click here
  1. Spiral cable sub-assembly
  2. Parking assist ECU
  3. Rear television camera assembly
  4. Navigation receiver assembly
Calibration
Parking assist monitor system (w/ Side Monitor System)
Click here
  1. Spiral cable sub-assembly
  2. Rear television camera assembly
  3. Navigation receiver assembly
Calibration
Parking assist monitor system (w/o Side Monitor System)
Click here
  1. Spiral cable sub-assembly
  2. Parking assist ECU
  3. Front passenger side television camera assembly
  4. Driver side television camera assembly
  5. Outer rear view mirror assembly
  6. Navigation receiver assembly
Calibration
Side monitor system
Click here
w/ Entry and Start System
  1. Steering lock actuator assembly
  2. Certification ECU
  3. ID code box
  4. Key
Code registration
  1. Engine immobiliser system
  2. Engine start
  3. Steering lock and unlock
  4. Entry and Start System (for Entry Function)
  5. Wireless door lock control system
Refer to the Service Bulletin for the registration procedure.
w/o Entry and Start System
  1. Transponder key ECU
  2. ECM
  3. Key
Code registration
  1. Engine immobiliser system
  2. Engine start
Refer to the Service Bulletin for the registration procedure.
  1. Door control receiver assembly
  2. Key
Code registration
Wireless door lock control system (w/o Entry and Start System)
Click here
Fold seat control ECU
Position memory initialization
Rear power seat system
Click here
  1. Front power window regulator motor LH
  2. Front power window regulator motor RH
  3. Rear power window regulator motor LH
  4. Rear power window regulator motor RH
Motor initialization
Power window control system
Click here
  1. Sliding roof ECU (sliding roof drive gear sub-assembly)
  2. Sliding roof glass
  3. Sliding roof housing
Sliding roof system initialization
  1. DTC B2343 output
  2. AUTO operation
  3. Jam protection function
  4. Key-off operation
  5. Wireless transmitter-linked operation function
  6. Key-linked operation function
Click here
  1. Height control sensor
  2. Headlight leveling ECU
  3. Suspension
Headlight leveling ECU initialization
Headlight leveling function
Click here
← INITIALIZATION (Aug 2013 – Jul 2014)GENERAL INFORMATION (from Aug 2013) →