TERMINALS OF ECU
System information · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system (Click here).
- NOTICE:
- Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
- Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
| JUNCTION CONNECTOR |
No. 1 Junction Connector


Text in Illustration *a
for No. 5 Junction Connector
*b
for No. 2 Junction Connector (V2 Bus)
*c
for No. 2 Junction Connector (V1 Bus)
*d
for Combination Meter Assembly
*e
- for Master Cylinder Solenoid (Skid control ECU) (w/ Vehicle Stability Control System [for Hydraulic Brake Booster])
- for Brake Actuator Assembly (Skid Control ECU) (w/o Vehicle Stability Control System)
-
-
No. 1 Junction Connector
Wiring Color
Connect to
A72-1 (CANH)
LG
No. 5 junction connector
A72-12 (CANL)
W
A72-2 (CANH)
B
No. 2 junction connector (V2 bus)
A72-13 (CANL)
W
A72-9 (CANH)
B
No. 2 junction connector (V1 bus)
A72-20 (CANL)
W
A72-10 (CANH)
LG
Combination meter assembly
A72-21 (CANL)
W
A72-11 (CANH)
R
- Master cylinder solenoid (skid control ECU)*1
- Brake actuator assembly (skid control ECU)*2
A72-22 (CANL)
W
- *1: w/ Vehicle Stability Control System (for Hydraulic Brake Booster)
- *2: w/o Vehicle Stability Control System
- for Master Cylinder Solenoid (Skid control ECU) (w/ Vehicle Stability Control System [for Hydraulic Brake Booster])
No. 2 Junction Connector
G132 No. 2 Junction Connector


Text in Illustration *a
for No. 3 Junction Connector
*b
for Main Body ECU (Multiplex Network Body ECU)
*c
for DLC3
*d
for Center Airbag Sensor Assembly
*e
for Spiral Cable Sub-assembly (Steering Angle Sensor) (w/ Vehicle Stability Control System [for Hydraulic Brake Booster])
*f
for No. 1 Junction Connector
*g
for Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])
-
-
No. 2 Junction Connector
Wiring Color
Connect to
G132-1 (CANH)
GR
No. 3 junction connector
G132-12 (CANL)
W
G132-2 (CANH)
L
Main body ECU (multiplex network body ECU)
G132-13 (CANL)
W
G132-4 (CANH)
R
DLC3
G132-15 (CANL)
W
G132-5 (CANH)
Y
Center airbag sensor assembly
G132-16 (CANL)
W
G132-7 (CANH)
G
Spiral cable sub-assembly (steering angle sensor)*1
G132-18 (CANL)
W
G132-8 (CANH)
B
No. 1 junction connector
G132-19 (CANL)
W
G132-9 (CANH)
P
Radio and display receiver assembly*2
G132-20 (CANL)
W
- *1: w/ Vehicle Stability Control System (for Hydraulic Brake Booster)
- *2: w/ Audio and Visual System (for Radio and Display Type)
- *1: w/ Vehicle Stability Control System (for Hydraulic Brake Booster)
G95 No. 2 Junction Connector (w/ TOYOTA Parking Assist-sensor System [for 4 Sensor Type])


Text in Illustration *a
for No. 3 Junction Connector
*b
for Clearance Warning ECU Assembly
*b
for No. 1 Junction Connector
-
-
No. 2 Junction Connector
Wiring Color
Connect to
G95-1 (CANH)
P
No. 3 junction connector
G95-12 (CANL)
W
G95-2 (CANH)
R
Clearance warning ECU assembly
G95-13 (CANL)
W
G95-3 (CANH)
B
No. 1 junction connector
G95-14 (CANL)
W
No. 3 Junction Connector
G134 No. 3 Junction Connector


Text in Illustration *a
for No. 2 Junction Connector
*b
- for ECM (for 1KD-FTV)
- for No. 4 Junction Connector (for 5L-E)
*c
for Four Wheel Drive Control ECU
*d
for Air Conditioning Amplifier Assembly
*e
for Power Steering ECU Assembly (for 1KD-FTV)
*f
for Network Gateway ECU (w/ TOYOTA Parking Assist-sensor System [for 4 Sensor Type])
*g
for Yaw Rate Sensor Assembly
-
-
No. 3 Junction Connector
Wiring Color
Connect to
G134-1 (CANH)
GR
No. 2 junction connector
G134-12 (CANL)
W
G134-2 (CANH)
LG
- ECM*1
- No. 4 junction connector*2
G134-13 (CANL)
W
G134-3 (CANH)
G
Four wheel drive control ECU
G134-14 (CANL)
W
G134-4 (CANH)
BR
Air conditioning amplifier assembly
G134-15 (CANL)
W
G134-5 (CANH)
L
Power steering ECU assembly*1
G134-16 (CANL)
W
G134-6 (CANH)
BR
Network gateway ECU*3
G134-17 (CANL)
W
G134-8 (CANH)
R
Yaw rate sensor assembly
G134-19 (CANL)
W
- *1: for 1KD-FTV
- *2: for 5L-E
- *3: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type)
- for ECM (for 1KD-FTV)
G98 No. 3 Junction Connector (w/ TOYOTA Parking Assist-sensor System [for 4 Sensor Type])


Text in Illustration *a
for Network Gateway ECU
*b
for No. 2 Junction Connector
No. 3 Junction Connector
Wiring Color
Connect to
G98-1 (CANH)
V
Network gateway ECU
G98-12 (CANL)
W
G98-3 (CANH)
P
No. 2 junction connector
G98-14 (CANL)
W
No. 4 Junction Connector (for 5L-E)

Text in Illustration *a
for No. 3 Junction Connector
No. 4 Junction Connector
Wiring Color
Connect to
G101-2 (CANN)
W
No. 3 junction connector
G101-3 (CANP)
LG
No. 5 Junction Connector (w/ TOYOTA Parking Assist-sensor System [for 4 Sensor Type])

Text in Illustration *a
for No. 1 Junction Connector
No. 5 Junction Connector
Wiring Color
Connect to
G102-2 (CANL)
W
No. 1 junction connector
G102-3 (CANH)
LG
| CHECK DLC3 |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
G48-6 (CANH) - G48-14 (CANL)
R - W
Ignition switch off
54 to 69 Ω
G48-6 (CANH) - G48-4 (CG)
R - W-B
Ignition switch off
200 Ω or higher
G48-14 (CANL) - G48-4 (CG)
W - W-B
Ignition switch off
200 Ω or higher
G48-6 (CANH) - G48-16 (BAT)
R - GR
Ignition switch off
6 kΩ or higher
G48-14 (CANL) - G48-16 (BAT)
W - GR
Ignition switch off
6 kΩ or higher
| CHECK ECM (for 1KD-FTV) |


Disconnect the C93, G57 and G58 ECM connectors.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
G58-35 (CANH) - G58-36 (CANL)
LG - W
Ignition switch off
108 to 132 Ω
G58-35 (CANH) - C93-1 (E1)
LG - BR
Ignition switch off
200 Ω or higher
G58-36 (CANL) - C93-1 (E1)
W - BR
Ignition switch off
200 Ω or higher
G58-35 (CANH) - G57-23 (BATT)
LG - L
Ignition switch off
6 kΩ or higher
G58-36 (CANL) - G57-23 (BATT)
W - L
Ignition switch off
6 kΩ or higher
| CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |


| *1 |
Main Body ECU (Multiplex Network Body ECU) |
- |
- |
Remove the main body ECU (multiplex network body ECU) (Click here).
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
G64-14 (CANH) - G64-13 (CANL)
L - W
Ignition switch off
54 to 69 Ω
G64-14 (CANH) - A-11 (GND1)
L - None
Ignition switch off
200 Ω or higher
G64-13 (CANL) - A-11 (GND1)
W - None
Ignition switch off
200 Ω or higher
G64-14 (CANH) - A-30 (BECU)
L - None
Ignition switch off
6 kΩ or higher
G64-13 (CANL) - A-30 (BECU)
W - None
Ignition switch off
6 kΩ or higher
| CHECK NETWORK GATEWAY ECU (w/ TOYOTA Parking Assist-sensor System [for 4 Sensor Type]) |


| *A |
for V1 Bus |
*B |
for V2 Bus |
Disconnect the G155 network gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
for V1 Bus Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
G155-16 (CA1H) - G155-15 (CA1L)
BR - W
Ignition switch off
54 to 69 Ω
G155-16 (CA1H) - G155-4 (GND)
BR - W-B
Ignition switch off
200 Ω or higher
G155-15 (CA1L) - G155-4 (GND)
W - W-B
Ignition switch off
200 Ω or higher
G155-16 (CA1H) - G155-2 (BATT)
BR - L
Ignition switch off
6 kΩ or higher
G155-15 (CA1L) - G155-2 (BATT)
W - L
Ignition switch off
6 kΩ or higher
for V2 Bus Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
G155-13 (CA2H) - G155-12 (CA2L)
L - W
Ignition switch off
108 to 132 Ω
G155-13 (CA2H) - G155-4 (GND)
L - W-B
Ignition switch off
200 Ω or higher
G155-12 (CA2L) - G155-4 (GND)
W - W-B
Ignition switch off
200 Ω or higher
G155-13 (CA2H) - G155-2 (BATT)
L - L
Ignition switch off
6 kΩ or higher
G155-12 (CA2L) - G155-2 (BATT)
W - L
Ignition switch off
6 kΩ or higher
| CHECK COMBINATION METER ASSEMBLY |


Disconnect the G6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
G6-40 (CANH) - G6-39 (CANL)
LG - W
Ignition switch off
108 to 132 Ω
G6-40 (CANH) - G6-21 (E2)
LG - BR
Ignition switch off
200 Ω or higher
G6-39 (CANL) - G6-21 (E2)
W - BR
Ignition switch off
200 Ω or higher
G6-40 (CANH) - G6-26 (B)
LG - L
Ignition switch off
6 kΩ or higher
G6-39 (CANL) - G6-26 (B)
W - L
Ignition switch off
6 kΩ or higher
| CHECK POWER STEERING ECU ASSEMBLY (for 1KD-FTV) |


Disconnect the G46 power steering ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
G46-1 (CANH) - G46-2 (CANL)
L - W
Ignition switch off
54 to 69 Ω
G46-1 (CANH) - G46-3 (GND)
L - W-B
Ignition switch off
200 Ω or higher
G46-2 (CANL) - G46-3 (GND)
W - W-B
Ignition switch off
200 Ω or higher
G46-1 (CANH) - G48-16 (BAT)
L - GR
Ignition switch off
6 kΩ or higher
G46-2 (CANL) - G48-16 (BAT)
W - GR
Ignition switch off
6 kΩ or higher
| CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |


Disconnect the G25 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Condition
Specified Condition
G25-11 (CANH) - G25-12 (CANL)
BR - W
Ignition switch off
54 to 69 Ω
G25-11 (CANH) - G25-14 (GND)
BR - W-B
Ignition switch off
200 Ω or higher
G25-12 (CANL) - G25-14 (GND)
W - W-B
Ignition switch off
200 Ω or higher
G25-11 (CANH) - G25-21 (B)
BR - V
Ignition switch off
6 kΩ or higher
G25-12 (CANL) - G25-21 (B)
W - V
Ignition switch off
6 kΩ or higher
| CHECK CENTER AIRBAG SENSOR ASSEMBLY |


Disconnect the G1 center airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
G1-13 (CANH) - G1-22 (CANL)
Y - W
Ignition switch off
54 to 69 Ω
G1-13 (CANH) - G1-25 (E1)
Y - W-B
Ignition switch off
200 Ω or higher
G1-22 (CANL) - G1-25 (E1)
W - W-B
Ignition switch off
200 Ω or higher
G1-13 (CANH) - G48-16 (BAT)
Y - GR
Ignition switch off
6 kΩ or higher
G1-22 (CANL) - G48-16 (BAT)
W - GR
Ignition switch off
6 kΩ or higher
| CHECK MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (w/ Vehicle Stability Control System [for Hydraulic Brake Booster]) |


Disconnect the A7 master cylinder solenoid (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
A7-11 (CANH) - A7-25 (CANL)
R - W
Ignition switch off
54 to 69 Ω
A7-11 (CANH) - A7-1 (GND1)
R - W-B
Ignition switch off
200 Ω or higher
A7-25 (CANL) - A7-1 (GND1)
W - W-B
Ignition switch off
200 Ω or higher
A7-11 (CANH) - A7-2 (+BM1)
R - B
Ignition switch off
6 kΩ or higher
A7-25 (CANL) - A7-2 (+BM1)
W - B
Ignition switch off
6 kΩ or higher
| CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/o Vehicle Stability Control System) |


Disconnect the A6 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
A6-25 (CANH) - A6-14 (CANL)
R - W
Ignition switch off
54 to 69 Ω
A6-25 (CANH) - A6-1 (GND1)
R - W-B
Ignition switch off
200 Ω or higher
A6-14 (CANL) - A6-1 (GND1)
W - W-B
Ignition switch off
200 Ω or higher
A6-25 (CANH) - A6-24 (BM)
R - B
Ignition switch off
6 kΩ or higher
A6-14 (CANL) - A6-24 (BM)
W - B
Ignition switch off
6 kΩ or higher
| CHECK SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (w/ Vehicle Stability Control [for Hydraulic Brake Booster]) |
![]() ![]() |
Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
G33-4 (CANH) - G33-3 (CANL)
G - W
Ignition switch off
54 to 69 Ω
G33-4 (CANH) - G33-2 (ESS)
G - W-B
Ignition switch off
200 Ω or higher
G33-3 (CANL) - G33-2 (ESS)
W - W-B
Ignition switch off
200 Ω or higher
G33-4 (CANH) - G33-6 (BAT)
G - L
Ignition switch off
6 kΩ or higher
G33-3 (CANL) - G33-6 (BAT)
W - L
Ignition switch off
6 kΩ or higher
| CHECK YAW RATE SENSOR ASSEMBLY |


Disconnect the G52 yaw rate sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
G52-3 (CANH) - G52-2 (CANL)
R - W
Ignition switch off
54 to 69 Ω
G52-3 (CANH) - G52-1 (GND)
R - W-B
Ignition switch off
200 Ω or higher
G52-2 (CANL) - G52-1 (GND)
W - W-B
Ignition switch off
200 Ω or higher
G52-3 (CANH) - G48-16 (BAT)
R - GR
Ignition switch off
6 kΩ or higher
G52-2 (CANL) - G48-16 (BAT)
W - GR
Ignition switch off
6 kΩ or higher
| CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type]) |


Disconnect the H49 and H51 radio and display receiver assembly connectors.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
H51-9 (CANH) - H51-10 (CANL)
W - P
Ignition switch off
54 to 69 Ω
H51-9 (CANH) - H49-7 (GND1)
W - BR
Ignition switch off
200 Ω or higher
H51-10 (CANL) - H49-7 (GND1)
P - BR
Ignition switch off
200 Ω or higher
H51-9 (CANH) - H49-4 (+B1)
W - R
Ignition switch off
6 kΩ or higher
H51-10 (CANL) - H49-4 (+B1)
P - R
Ignition switch off
6 kΩ or higher
| CHECK FOUR WHEEL DRIVE CONTROL ECU |


Disconnect the G53 and G54 four wheel drive control ECU connectors.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
G53-19 (CANH) - G53-20 (CANL)
G - W
Ignition switch off
54 to 69 Ω
G53-19 (CANH) - G54-4 (GND)
G - W-B
Ignition switch off
200 Ω or higher
G53-20 (CANL) - G54-4 (GND)
W - W-B
Ignition switch off
200 Ω or higher
G53-19 (CANH) - G48-16 (BAT)
G - GR
Ignition switch off
6 kΩ or higher
G53-20 (CANL) - G48-16 (BAT)
W - GR
Ignition switch off
6 kΩ or higher
| CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System [for 4 Sensor Type]) |


Disconnect the I1 clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
I1-3 (R1) - I1-5 (R2)
R - W
Ignition switch off
54 to 69 Ω
I1-3 (R1) - I1-17 (E)
R - W-B
Ignition switch off
200 Ω or higher
I1-5 (R2) - I1-17 (E)
W - W-B
Ignition switch off
200 Ω or higher
I1-3 (R1) - G48-16 (BAT)
R - GR
Ignition switch off
6 kΩ or higher
I1-5 (R2) - G48-16 (BAT)
W - GR
Ignition switch off
6 kΩ or higher
