TERMINALS OF ECU
System information · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |


| *A |
for LHD |
*B |
for RHD |
Remove the main body ECU (Click here).
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction in the wire harness.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A-30 (BECU) - Body ground
-
Auxiliary battery power supply
Always
11 to 14 V
A-31 (ALTB) - Body ground
-
Auxiliary battery power supply
Always
11 to 14 V
A-32 (IG) - Body ground
-
Engine switch power supply
Engine switch on (IG)
11 to 14 V
A-32 (IG) - Body ground
-
Engine switch power supply
Engine switch off
Below 1 V
A-29 (ACC) - Body ground
-
ACC power supply
Engine switch on (ACC)
11 to 14 V
A-29 (ACC) - Body ground
-
ACC power supply
Engine switch off
Below 1 V
A-11 (GND1) - Body ground
-
Ground
Always
Below 1 Ω
G63-3 (GND2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Install the main body ECU (Click here).
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
2I-27 (FLCY) - Body ground*1
R - Body ground
Front door LH courtesy switch input
Front door LH open
Below 1 V
2I-27 (FLCY) - Body ground*1
R - Body ground
Front door LH courtesy switch input
Front door LH closed
11 to 14 V
2D-31 (FLCY) - Body ground*2
R - Body ground
Front door LH courtesy switch input
Front door LH open
Below 1 V
2D-31 (FLCY) - Body ground*2
R - Body ground
Front door LH courtesy switch input
Front door LH closed
11 to 14 V
2D-15 (FRCY) - Body ground*1
B - Body ground
Front door RH courtesy switch input
Front door RH open
Below 1 V
2D-15 (FRCY) - Body ground*1
B - Body ground
Front door RH courtesy switch input
Front door RH closed
11 to 14 V
2H-26 (FRCY) - Body ground*2
B - Body ground
Front door RH courtesy switch input
Front door RH open
Below 1 V
2H-26 (FRCY) - Body ground*2
B - Body ground
Front door RH courtesy switch input
Front door RH closed
11 to 14 V
G65-3 (LCTY) - Body ground*3
V - Body ground
Rear door LH courtesy light switch input
Rear door LH open
Below 1 V
G65-3 (LCTY) - Body ground*3
V - Body ground
Rear door LH courtesy light switch input
Rear door LH closed
11 to 14 V
G64-6 (RCTY) - Body ground*3
R - Body ground
Rear door RH courtesy light switch input
Rear door RH open
Below 1 V
G64-6 (RCTY) - Body ground*3
R - Body ground
Rear door RH courtesy light switch input
Rear door RH closed
11 to 14 V
G64-19 (BCTY) - Body ground
G - Body ground
Back door courtesy light switch input
Back door open
Below 1 V
G64-19 (BCTY) - Body ground
G - Body ground
Back door courtesy light switch input
Engine switch off, all doors closed and back door closed
Pulse generation (see waveform 1 or 2)
G64-1 (GCTY) - Body ground*4
V - Body ground
Glass hatch courtesy switch input
Glass hatch open
Below 1 V
G64-1 (GCTY) - Body ground*4
V - Body ground
Glass hatch courtesy switch input
Engine switch off, all doors closed and glass hatch closed
Pulse generation (see waveform 3 or 4)
G64-7 (LSFL) - Body ground
G - Body ground
Front door LH lock position switch input
Front door LH unlocked
Below 1 V
G64-7 (LSFL) - Body ground
G - Body ground
Front door LH lock position switch input
Engine switch off, all doors closed and front door LH locked
Pulse generation (see waveform 5 or 6)
G64-18 (LSFR) - Body ground
G - Body ground
Front door RH lock position switch input
Front door RH unlocked
Below 1 V
G64-18 (LSFR) - Body ground
G - Body ground
Front door RH lock position switch input
Engine switch off, all doors closed and front door RH locked
Pulse generation (see waveform 7 or 8)
2I-25 (LSWL) - Body ground*1, *3
B - Body ground
Rear door LH lock position switch input
Rear door LH unlocked
Below 1 V
2I-25 (LSWL) - Body ground*1, *3
B - Body ground
Rear door LH lock position switch input
Engine switch off, all doors closed and rear door LH locked
Pulse generation (see waveform 9 or 10)
2D-16 (LSWL) - Body ground*2, *3
B - Body ground
Rear door LH lock position switch input
Rear door LH unlocked
Below 1 V
2D-16 (LSWL) - Body ground*2, *3
B - Body ground
Rear door LH lock position switch input
Engine switch off, all doors closed and rear door LH locked
Pulse generation (see waveform 11 or 12)
G63-2 (LSWR) - Body ground*3
V - Body ground
Rear door RH lock position switch input
Rear door RH unlocked
Below 1 V
G63-2 (LSWR) - Body ground*3
V - Body ground
Rear door RH lock position switch input
Engine switch off, all doors closed and rear door RH locked
Pulse generation (see waveform 13 or 14)
G65-13 (LSWB) - Body ground
SB - Body ground
Back door lock position switch input
Back door lock unlocked
Below 1 V
G65-13 (LSWB) - Body ground
SB - Body ground
Back door lock position switch input
Engine switch off, all doors closed and back door locked
Pulse generation (see waveform 15 or 16)
2F-13 (BZR) - Body ground
GR - Body ground
Wireless door lock buzzer signal
Wireless door lock buzzer off
Below 1 V
2F-13 (BZR) - Body ground
GR - Body ground
Wireless door lock buzzer signal
Wireless door lock buzzer on
Pulse generation
G64-3 (HAZ) - Body ground
W - Body ground
Hazard warning signal light signal output
Hazard warning signal switch off
Below 1 V
G64-3 (HAZ) - Body ground
W - Body ground
Hazard warning signal light signal output
Hazard warning signal switch on
11 to 14 V
- *1: for LHD
- *2: for RHD
- *3: for 5 Door
- *4: w/ Glass Hatch Opener System
- *1: for LHD
Using an oscilloscope, check waveform 1.

Waveform 1 (Reference) Item
Content
Terminal No. (Symbol)
G64-19 (BCTY) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and back door closed
Using an oscilloscope, check waveform 2.

Waveform 2 (Reference) Item
Content
Terminal No. (Symbol)
G64-19 (BCTY) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and back door closed
Using an oscilloscope, check waveform 3.

Waveform 3 (Reference) Item
Content
Terminal No. (Symbol)
G64-1 (GCTY) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and glass hatch closed
Using an oscilloscope, check waveform 4.

Waveform 4 (Reference) Item
Content
Terminal No. (Symbol)
G64-1 (GCTY) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and glass hatch closed
Using an oscilloscope, check waveform 5.

Waveform 5 (Reference) Item
Content
Terminal No. (Symbol)
G64-7 (LSFL) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and front door LH locked
Using an oscilloscope, check waveform 6.

Waveform 6 (Reference) Item
Content
Terminal No. (Symbol)
G64-7 (LSFL) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and front door LH locked
Using an oscilloscope, check waveform 7.

Waveform 7 (Reference) Item
Content
Terminal No. (Symbol)
G64-18 (LSFR) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and front door RH locked
Using an oscilloscope, check waveform 8.

Waveform 8 (Reference) Item
Content
Terminal No. (Symbol)
G64-18 (LSFR) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and front door RH locked
Using an oscilloscope, check waveform 9.

Waveform 9 (Reference) Item
Content
Terminal No. (Symbol)
2I-25 (LSWL) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and rear door LH locked
Using an oscilloscope, check waveform 10.

Waveform 10 (Reference) Item
Content
Terminal No. (Symbol)
2I-25 (LSWL) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and rear door LH locked
Using an oscilloscope, check waveform 11.

Waveform 11 (Reference) Item
Content
Terminal No. (Symbol)
2D-16 (LSWL) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and rear door LH locked
Using an oscilloscope, check waveform 12.

Waveform 12 (Reference) Item
Content
Terminal No. (Symbol)
2D-16 (LSWL) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and rear door LH locked
Using an oscilloscope, check waveform 13.

Waveform 13 (Reference) Item
Content
Terminal No. (Symbol)
G63-2 (LSWR) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and rear door RH locked
Using an oscilloscope, check waveform 14.

Waveform 14 (Reference) Item
Content
Terminal No. (Symbol)
G63-2 (LSWR) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and rear door RH locked
Using an oscilloscope, check waveform 15.

Waveform 15 (Reference) Item
Content
Terminal No. (Symbol)
G65-13 (LSWB) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and back door locked
Using an oscilloscope, check waveform 16.

Waveform 16 (Reference) Item
Content
Terminal No. (Symbol)
G65-13 (LSWB) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Engine switch off, all doors closed and back door locked
| CHECK CERTIFICATION ECU |


Disconnect the G38 ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G38-1 (+B) - G38-15 (E)
V - W-B
+B power supply
Always
11 to 14 V
G38-15 (E) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
G38-16 (IG) - G38-15 (E)
W - W-B
IG power supply
Engine switch off → Engine switch on (IG)
Below 1 V → 11 to 14 V
G38-17 (CUTB) - G38-15 (E)
L - W-B
+B power supply
Always
11 to 14 V
- If the result is not as specified, there may be a malfunction in the wire harness.
- If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the G38 ECU connector.
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G39-5 (RCO) - G38-15 (E)
L - W-B
Door control receiver power source
Engine switch off, all doors closed and transmitter switch not pressed → pressed
Below 1 V → 4.5 to 5.5 V
G39-15 (RDA) - G38-15 (E)
G - W-B
Door control receiver data input signal
Engine switch off
11 to 14 V pulse generation at regular intervals
G39-16 (RSSI) - G38-15 (E)
P - W-B
Door control receiver electric wave existence signal
All doors locked, all doors closed and transmitter switch not pressed → pressed
11 to 14 V → Below 2 V
- If the result is not as specified, the certification ECU may have a malfunction.
- If the result is not as specified, the certification ECU may have a malfunction.