2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

19 (1) Accelerator Position Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
  1. This is a troubleshooting procedure for the accelerator pedal position sensor.
  2. This electrical throttle system does not use a throttle cable.
  3. This accelerator pedal position sensor is a non-contact type.

The accelerator pedal position sensor is mounted on the accelerator pedal to detect the position of the accelerator pedal. Since this sensor is electronically controlled with hall elements, accurate control and reliability can be obtained. It has 2 sensors in order to detect the accelerator position and malfunctions of the accelerator position sensor.
Due to the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the ECM changes between 0 V and 5 V according to the position of the accelerator pedal. VPA is a signal which indicates the actual accelerator pedal position and is used for engine control, and VPA2 is a signal which indicates information about the position and is used for detecting malfunctions. Based on the signals input to terminals VPA and VPA2, the ECM determines the current position of the accelerator pedal and controls the injection pump.
A112620E33
DTC No.
DTC Detection Condition
Trouble Area
19 (1)
Condition (a), (b), (c) or (d) continues for 2.0 seconds:
(a) VPA is 0.2 V or less and VPA2 is 0.5 V or less.
(b) VPA is 4.8 V or higher.
(c) VPA is 0.2 V or higher and 3.45 V or less, and VPA2 is 4.8 V or higher.
(d) "VPA minus VPA2" is 0.02 V or less.
  1. Open or short in accelerator pedal position sensor circuit
  2. Accelerator pedal position sensor
  3. ECM
Condition (a) continues for 0.5 seconds:
(a) VPA is 0.2 V or less, or VPA2 is 0.5 V or less.

WIRING DIAGRAM

A227801E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


When using intelligent tester:


1. READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION)

  1. FI07052E37
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Position.

  1. Check that the value displayed on the intelligent tester changes when repeatedly depressing and releasing the accelerator pedal.

    OK:
    Value changes.

    Text in Illustration 
    *a
    Depressed
    *b
    Released



NG
Go to step 3
OK


2. READ OUTPUT DTC (CHECK IF ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN)
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine and idle it for 15 seconds or more.

  1. Read the DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC 19 (1) output again
    A
    No DTC output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)

3. CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A19-1 (VCP2) - C102-1 (VC)
    Always
    Below 1 Ω
    A19-2 (EPA2) - C102-9 (E2)
    Always
    Below 1 Ω
    A19-3 (VPA2) - G62-12 (VPA2)
    Always
    Below 1 Ω
    A19-4 (VCPA) - G62-6 (VCPA)
    Always
    Below 1 Ω
    A19-5 (EPA) - G62-4 (EPA)
    Always
    Below 1 Ω
    A19-6 (VPA) - G62-5 (VPA)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A19-1 (VCP2) or C102-1 (VC) - Body ground
    Always
    10 kΩ or higher
    A19-2 (EPA2) or C102-9 (E2) - Body ground
    Always
    10 kΩ or higher
    A19-3 (VPA2) or G62-12 (VPA2) - Body ground
    Always
    10 kΩ or higher
    A19-4 (VCPA) or G62-6 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A19-5 (EPA) or G62-4 (EPA) - Body ground
    Always
    10 kΩ or higher
    A19-6 (VPA) or G62-5 (VPA) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK ECM (VC, VCPA VOLTAGE)

  1. A110530E06
    Disconnect the accelerator pedal position sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C102-1 (VC) - C102-9 (E2)
    Ignition switch ON
    4.5 to 5.5 V
    G62-6 (VCPA) - G62-4 (EPA)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Accelerator pedal position sensor connector
    *a
    Component with harness connected
    (ECM)

  1. Reconnect the accelerator pedal position sensor connector.



NG
REPLACE ECM (Click here)
OK


5. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
  1. Replace the accelerator pedal rod assembly (Click here).


NEXT


6. READ OUTPUT DTC (CHECK IF ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN)
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine and idle it for 15 seconds or more.

  1. Read the DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC 19 (1) output again
    A
    No DTC output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)


When not using intelligent tester:


1. CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A19-1 (VCP2) - C102-1 (VC)
    Always
    Below 1 Ω
    A19-2 (EPA2) - C102-9 (E2)
    Always
    Below 1 Ω
    A19-3 (VPA2) - G62-12 (VPA2)
    Always
    Below 1 Ω
    A19-4 (VCPA) - G62-6 (VCPA)
    Always
    Below 1 Ω
    A19-5 (EPA) - G62-4 (EPA)
    Always
    Below 1 Ω
    A19-6 (VPA) - G62-5 (VPA)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A19-1 (VCP2) or C102-1 (VC) - Body ground
    Always
    10 kΩ or higher
    A19-2 (EPA2) or C102-9 (E2) - Body ground
    Always
    10 kΩ or higher
    A19-3 (VPA2) or G62-12 (VPA2) - Body ground
    Always
    10 kΩ or higher
    A19-4 (VCPA) or G62-6 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A19-5 (EPA) or G62-4 (EPA) - Body ground
    Always
    10 kΩ or higher
    A19-6 (VPA) or G62-5 (VPA) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK ECM (VC, VCPA VOLTAGE)

  1. A110530E06
    Disconnect the accelerator pedal position sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C102-1 (VC) - C102-9 (E2)
    Ignition switch ON
    4.5 to 5.5 V
    G62-6 (VCPA) - G62-4 (EPA)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Accelerator pedal position sensor connector
    *a
    Component with harness connected
    (ECM)

  1. Reconnect the accelerator pedal position sensor connector.



NG
REPLACE ECM (Click here)
OK


3. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
  1. Replace the accelerator pedal rod assembly (Click here).


NEXT


4. READ OUTPUT DTC (CHECK IF ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN)
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine and idle it for 15 seconds or more.

  1. Read the DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC 19 (1) output again
    A
    No DTC output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)


← 18 (5) Spill Control Circuit Malfunction (from Aug 2014)19 (1) Accelerator Position Sensor Circuit Malfunction (from Aug 2014) →