Headlight Relay Circuit
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The main body ECU receives headlight dimmer switch information signals and illuminates the low beam headlights.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT RELAY) |
 |
Using the intelligent tester, perform the Active Test (Click here).
Main Body
Tester Display
|
Test Part
|
Control Range
|
Diagnostic Note
|
Headlight Relay
|
Low beam headlight relay
|
ON/OFF
|
-
|
- OK:
- Headlight relay operates (low beam headlights illuminate).
|
NG |
 |
|
|
|
| OK |
|
 |
|
| REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
|
|
| 2. INSPECT HEADLIGHT RELAY (H-LP LO) |
 |
- Remove the headlight relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
3 - 5
|
Battery voltage not applied between terminals 1 and 2
|
10 kΩ or higher
|
3 - 5
|
Battery voltage applied between terminals 1 and 2
|
Below 1 Ω
|
|
NG |
 |
|
| REPLACE HEADLIGHT RELAY (H-LP LO) |
|
|
| OK |
|
 |
|
| 3. CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - BATTERY) |
 |
- Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
Headlight relay terminal 1 - Body ground
|
Always
|
11 to 14 V
|
Headlight relay terminal 5 - Body ground
|
Text in Illustration
*a
|
Front view of wire harness connector (to Headlight Relay [H-LP LO])
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 4. CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY) |
 |
Remove the headlight relay from the engine room relay block.
Disconnect the 2F driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Headlight relay terminal 2 - 2F-40
|
Always
|
Below 1 Ω
|
2F-40 - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 5. INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY |
 |
Remove the driver side junction block assembly (Click here).
Remove the main body ECU from the driver side junction block assembly (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A-15 (HRLY) - 2F-40
|
Always
|
Below 1 Ω
|
|
NG |
 |
|
| REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (Click here)
|
|
|
| OK |
|
 |
|
| PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
|
|