2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

Daytime Running Light Relay Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The main body ECU controls the daytime running lights.

WIRING DIAGRAM

E283914E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DAYTIME RUNNING LIGHT)
  1. Using the intelligent tester, perform the Active Test (Click here).

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Daytime Running Light
    Daytime running light relay
    ON/OFF
    -

    OK:
    Daytime running Lights illuminate.



NG
Go to step 2
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

2. INSPECT DAYTIME RUNNING LIGHT RELAY (DRL)

  1. E108359E15
    Remove the daytime running light relay from the engine room No. 5 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE DAYTIME RUNNING LIGHT RELAY RELAY (DRL)
OK


3. CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT RELAY [DRL] - BATTERY)

  1. E282870E01
    Remove the daytime running light relay from the engine room No. 5 relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Daytime running light relay terminal 5 - Body ground
    Always
    11 to 14 V
    Daytime running light relay terminal 2 - Body ground

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Daytime Running Light Relay [DRL])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (DAYTIME RUNNING LIGHT RELAY [DRL] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
  1. Remove the daytime running light relay from the engine room No. 5 relay block.

  1. Disconnect the 2F driver side junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Daytime running light relay terminal 1 - 2F-24
    Always
    Below 1 Ω
    2F-24 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

  1. E283382E02
    Remove the driver side junction block assembly (Click here).

  1. Remove the main body ECU from the driver side junction block assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-22 (DRL) - 2F-24
    Always
    Below 1 Ω



NG
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Headlight Relay Circuit (from Aug 2014)Daytime Running Light Relay Circuit (from Aug 2014) →