2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

Navigation ECU Communication Stop Mode

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Detection Item
Symptom
Trouble Area
Navigation ECU Communication Stop Mode
Either condition is met:
  1. "Display and Navigation (AVN1)" is not displayed on "Bus Check".
  2. "Navigation ECU Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside of navigation receiver assembly
  2. Navigation receiver assembly CAN branch wire or connector
  3. Navigation receiver assembly
  1. For vehicles with a navigation system (for navigation receiver type).

WIRING DIAGRAM

C280381E05

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAB main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE)

  1. C235416E12
    Disconnect the H56 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H56-9 (CANH) - H56-10 (CANL)
    Engine switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)



NG
REPAIR OR REPLACE NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

  1. C277477E04
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the H54 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H54-7 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H54-4 (+B1) - Body ground
    Always
    11 to 14 V
    H54-3 (ACC1) - Body ground
    Engine switch on (ACC)
    11 to 14 V
    H56-1 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Navigation Receiver Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)


← Navigation ECU Communication Stop Mode (Aug 2013 – Jul 2014)Audio Receiver Assembly Communication Stop Mode (Aug 2013 – Jul 2014) →