2013-2015 Land Cruiser Prado · Service Manual Drivetrain

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A224743
    Remove the 4 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.


3. REMOVE REAR ENGINE UNDER COVER ASSEMBLY
  1. Remove the 4 bolts and rear engine under cover.


4. REMOVE FRONT FENDER APRON SEAL RH

  1. C214927
    Remove the 5 clips and front fender apron seal RH.


5. REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

  1. C214928
    Remove the 5 clips and front No. 1 fender apron to frame seal.


6. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the front exhaust pipe (Click here).


7. REMOVE TRANSFER CASE LOWER PROTECTOR
  1. Remove the 4 bolts and protector.


8. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
  1. Remove the front propeller shaft (Click here).


9. REMOVE PROPELLER SHAFT ASSEMBLY
  1. Remove the propeller shaft (Click here).


10. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


11. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

C213708
  1. Remove the transmission oil dipstick.

  1. Remove the 2 bolts and oil filler tube.

  1. Remove the O-ring from the oil filler tube.


12. DISCONNECT NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE

  1. C213721
    Remove the 3 bolts to open 2 No. 2 oil cooler hose clamps.

  1. C118031
    Using a union nut wrench, disconnect the inlet tube and outlet tube.


13. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

C214917E01
  1. Remove the nut and clip, and disconnect the transmission control cable.


14. REMOVE STARTER ASSEMBLY
  1. for 1.4 kW Type:
    Remove the starter (Click here).

  1. for 2.0 kW Type:
    Remove the starter (Click here).


15. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

C213723
  1. Support the transmission with a transmission jack.


16. REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH

C214922
  1. Remove the 8 bolts and front suspension member bracket LH and RH.


17. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

C214923
  1. Remove the 4 bolts of the rear engine mounting insulator.

  1. C213724
    Remove the 4 nuts, 4 bolts and frame crossmember.


18. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

C213729
  1. Remove the bolt and rear engine mounting heat insulator

  1. Remove the 4 bolts and engine mounting insulator from the transmission.


19. DISCONNECT WIRE HARNESS AND CONNECTOR

C214940
  1. Remove the nut and disconnect the ground cable.

  1. C214924
    Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer control side connector.

  1. Detach the connector clamp and 5 harness clamps, and disconnect the wire harness.

    C213725E01


20. DISCONNECT BREATHER HOSE

C213726
  1. Disconnect the 2 transfer breather hoses from the engine.


21. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT
  1. Remove the flywheel housing dust seal.

  1. C118033
    Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.


22. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

C214941
  1. Remove the 3 bolts and exhaust manifold stay.

  1. C213727
    Remove the 7 bolts and transmission.

    NOTICE:
    Do not use excess force when prying the transmission assembly.


23. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

G024484E01
  1. Remove the 2 bolts and control cable bracket from the transmission.


24. REMOVE TRANSFER ASSEMBLY
  1. Remove the transfer (Click here).


25. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY
← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →