2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

B1244 Light Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal and outputs it to the main body ECU. The main body ECU turns the headlights and taillights on or off according to the signal.
DTC Code
DTC Detection Condition
Trouble Area
B1244
  1. Malfunction in the automatic light control sensor.
  2. Open or short in the automatic light control sensor circuit.
  1. Automatic light control sensor
  2. Main body ECU (multiplex network body ECU)
  3. Harness or connector

WIRING DIAGRAM

E188439E04

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1244 output does not occur.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. READ VALUE USING INTELLIGENT TESTER (AUTOMATIC LIGHT CONTROL SENSOR)
  1. Using the intelligent tester, read the Data List (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Illumination Rate
    Illumination rate information / 0 ms. to 99.99 ms.
    Value output according to ambient light levels
    -

    OK:
    Normal condition listed above is displayed.



NG
Go to step 3
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
  1. Disconnect the G64 main body ECU connector.

  1. Disconnect the H19 automatic light control sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G64-22 (CLTE) - H19-3 (CLTE)
    Always
    Below 1 Ω
    G64-21 (CLTS) - H19-5 (CLTS)
    Always
    Below 1 Ω
    G64-20 (CLTB) - H19-6 (CLTB)
    Always
    Below 1 Ω
    G64-22 (CLTE) - Body ground
    Always
    10 kΩ or higher
    G64-21 (CLTS) - Body ground
    Always
    10 kΩ or higher
    G64-20 (CLTB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

  1. E203228E06
    Reconnect the G64 main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G64-20 (CLTB) - G64-22 (CLTE)
    Ignition switch off
    Below 1 V
    Ignition switch ON and headlight dimmer switch in AUTO position
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Main Body ECU)



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK


5. CHECK AUTOMATIC LIGHT CONTROL SENSOR

  1. E203229E06
    Reconnect the H19 automatic light control sensor connector.

  1. Connect an oscilloscope to the automatic light control sensor connector.

    Text in Illustration 
    *a
    Component with harness connected
    (Automatic Light Control Sensor)

  1. B113714E01
    Check the waveform.

    OK:
    Tester Connection
    Tool Setting
    Switch Condition
    Specified Condition
    H19-5 (CLTS) - H19-3 (CLTE)
    5 V/DIV., 5 ms./DIV.
    Ignition switch ON
    Headlight dimmer switch AUTO Automatic light control sensor covered with a hand → Automatic light control sensor exposed to ambient light
    Correct waveform is as shown

    HINT:
    When the ambient light becomes brighter, width A becomes narrower.



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← B1244 Light Sensor Circuit Malfunction (Aug 2013 – Jul 2014)B2415 Vehicle Speed Sensor Malfunction (Aug 2013 – Jul 2014) →