2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REASSEMBLY

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.
  5. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. REPAIR INSTRUCTION
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Installation temperature.

    1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

      HINT:
      1. The most appropriate temperature for installing the tape is 25°C (77°F).
      2. When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.

  1. Before installation.

    1. Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

      HINT:
      Spray water on the shop floor to settle any dust.

  1. Key points for handling the tape.

    1. The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

      NOTICE:
      Do not bend the tape or leave it in a place with a high temperature.

  1. Key points for the installation of the tape (how to use a squeegee and the installation procedure for a flat surface).

    NOTICE:
    1. Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.
    2. The tape cannot be reused because it deforms and will not fit after removal.


    1. To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf) while moving the squeegee at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.

      B233855E02

      NOTICE:
      Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.

      HINT:
      1. Either angle of the squeegee (for pressing forward or for pulling) is acceptable.
      2. Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.

      Text in Illustration 
      *A
      Pressing
      *B
      Pulling
      *1
      Squeegee
      *2
      Black Out Tape
      *3
      Release Paper
      -
      -
      *a
      Sectional View
      *b
      Non-padded Side
      *c
      Padded Side
      -
      -

  1. B233856E02
    Key points for the installation of the tape (how to use a squeegee and the installation procedure for hemming surfaces).

    1. If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

      HINT:
      When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.

      Text in Illustration 
      *1
      Squeegee
      *a
      First
      *b
      Second
      *c
      Third

  1. Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners).

    1. Remove the release paper and apply the tape carefully with your fingers.

    2. Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles in the tape and achieve a neat finish.

  1. Check after installation.

    1. After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

      NOTICE:
      Do not reuse the tape.


2. INSTALL REAR DOOR OUTSIDE STRIPE LH

B236351E01
  1. Refer to the illustration to position a new rear door outside stripe.

    Reference Value:
    Area
    Specified Condition
    A
    +/-1.0 mm (0.039 in.) from End


3. INSTALL BLACK OUT TAPE LH

B236349E01
  1. Refer to the illustration to position a new black out tape.

    Reference Value:
    Area
    Specified Condition
    A
    +/-1.0 mm (0.039 in.) from End


4. INSTALL REAR DOOR LOWER OUTSIDE STRIPE LH

B247541E01
  1. Refer to the illustration to position a new rear door lower outside stripe.

    Reference Value:
    Area
    Specified Condition
    A
    +/-1.0 mm (0.039 in.) from End


5. INSTALL NO. 2 BLACK OUT TAPE LH

B236344E01
  1. Refer to the illustration to position a new No. 2 black out tape.

    Reference Value:
    Area
    Specified Condition
    A
    2 to 4 mm (0.078 to 0.158 in.)
    B
    4 to 6 mm (0.157 to 0.236 in.)


6. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body surface.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Install a new rear door front window frame moulding.

    1. Using a heat light, heat a new rear door front window frame moulding and the vehicle body surface.

    2. Remove the peeling paper from the face of the rear door front window frame moulding.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Attach the clip and double-sided tape to install the rear door front window frame moulding.

      HINT:
      Press the rear door front window frame moulding firmly to install it.

  1. Install a new door window frame moulding clip.


7. INSTALL REAR DOOR BELT MOULDING LH
  1. Attach the 7 claws to install the rear door belt moulding.


8. INSTALL REAR DOOR PANEL CUSHION
  1. Attach the clip to install a new door panel cushion.


9. INSTALL REAR DOOR NO. 2 WEATHERSTRIP LH
  1. Attach the 6 clips and guide to install the rear door No. 2 weatherstrip.


10. INSTALL REAR DOOR WEATHERSTRIP LH
  1. Attach the 19 clips and guide to install the rear door weatherstrip.


11. INSTALL REAR DOOR CHECK ASSEMBLY LH
  1. Apply MP grease to the sliding areas of the rear door check assembly.

  1. B239622
    Install the door check to the door panel with the 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the door check to the body panel with the bolt.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }


12. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
  1. Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.

  1. B239673
    Attach the door handle nut and claw.

  1. Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }


13. INSTALL REAR DOOR NO. 2 OUTSIDE HANDLE PAD LH
  1. Attach the 2 claws to install the rear door No. 2 outside handle pad.


14. INSTALL REAR DOOR NO. 1 OUTSIDE HANDLE PAD LH
  1. Attach the 3 claws to install the rear door No. 1 outside handle pad.


15. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

  1. B239665
    Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.

    NOTICE:
    If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.

  1. Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.

  1. B239663
    Move the lever in the direction indicated by the arrow in the illustration to lock the door outside handle assembly.


16. INSTALL REAR DOOR OUTSIDE HANDLE COVER LH
  1. Attach the claw to install the rear door outside handle cover.

  1. Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }


17. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH
  1. Install the rear door inside locking cable assembly.

  1. Attach the 3 claws.


18. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
  1. Install the rear door lock remote control cable assembly.

  1. Attach the claw.


19. INSTALL REAR DOOR LOCK ASSEMBLY LH

NOTICE:
  1. When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the surface of the connector which contacts the door lock wiring harness seal.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may allow water into the connection. This may result in a malfunction of the rear door lock assembly.

  1. B237877E01
    Apply MP grease to the sliding parts of the rear door lock assembly.
    Text in Illustration 
    *A
    w/o Double Locking System
    *B
    w/ Double Locking System
    V100135
    Slide

  1. Install a new door lock wiring harness seal to the rear door lock assembly.

  1. Insert the rear door lock assembly into the rear door outside handle release plate, and set it on the rear door panel.

  1. Check that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

  1. Using a T30 "TORX" wrench, install the rear door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


20. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using a T25 "TORX" socket wrench, install the power window regulator motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.


21. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY LH
  1. Apply MP grease to the sliding parts of the rear door window regulator assembly.

  1. Install the temporary bolt to the rear door window regulator assembly.

  1. B239642E02
    Temporarily install the rear door window regulator assembly with the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Temporarily install the 3 bolts, and then tighten the temporary bolt and 3 bolts.

    HINT:
    Tighten the bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


22. INSTALL REAR DOOR GLASS CHANNEL FILLER

  1. B234459E02
    Apply soapy water to a new rear door glass channel filler.

    Standard:
    Area
    Specified Condition
    A
    21 mm (0.827 in.)
    B
    22.5 mm (0.886 in.)

    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side

  1. Install the rear door glass channel filler to the position shown in the illustration.


23. INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH

  1. B234461E03
    Apply soapy water to a new rear door glass channel sub-assembly.

    Standard:
    Area
    Specified Condition
    A
    21 mm (0.827 in.)
    B
    22.5 mm (0.886 in.)

    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side

    NOTICE:
    To prevent damaging the rear door glass sub-assembly, be careful not to strike the channel with too much force.

  1. Install the rear door glass channel sub-assembly to the position shown in the illustration.


24. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the cable to the negative (-) battery terminal and rear power window regulator motor connector.

  1. B241339
    Connect the power window regulator switch assembly and move the arm of the regulator so that the roller on the arm can be seen through the service hole.

  1. Disconnect the power window regulator switch assembly and rear power window regulator motor connector.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. B239637
    Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as indicated by the arrow in the illustration.


25. INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

  1. B241322
    Install the rear door quarter window weatherstrip to the rear door quarter window glass.


26. INSTALL REAR DOOR QUARTER WINDOW GLASS LH

  1. B239633
    Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.


27. INSTALL REAR DOOR FRAME GARNISH LH
  1. Attach the clip to install a new door frame garnish.


28. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
  1. Insert the rear door window division bar sub-assembly from above.

  1. Install the rear door window division bar sub-assembly to the glass run.

  1. Install the temporary bolt to the rear door window division bar sub-assembly.

  1. Install the rear door window division bar sub-assembly.

  1. Install the 2 bolts and screw.

  1. Tighten the temporary bolt to install the rear door window division bar sub-assembly.


29. INSTALL REAR DOOR GLASS RUN LH
  1. Install the glass run.


30. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply new butyl tape to the rear door panel.

  1. B239701E01
    Pass the rear door lock remote control cable assembly and rear door inside locking cable assembly through a new rear door service hole cover.

  1. Attach the rear door service hole cover using to the reference points on the rear door panel.

    Text in Illustration 
    *1
    Reference Point

    NOTICE:
    1. There should be no wrinkles or folds after attaching the service hole cover.
    2. After attaching the service hole cover, check the seal quality.

  1. Connect the connector.

  1. Attach the 2 clamps to the rear door wire.


31. INSTALL REAR SPEAKER SET

  1. B239136E01
    Temporarily install the speaker by attaching the 2 claws of the speaker to the door panel.

  1. Install the rear speaker set with the 3 screws in the order shown in the illustration.

    NOTICE:
    Do not touch the cone of the speaker.

  1. Connect the connector.


32. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  1. B239618
    Attach the guide and 2 claws to install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.

  1. Install the 2 screws.

  1. B239610
    Install the 8 screws to the rear door armrest.


33. INSTALL REAR NO. 2 SPEAKER ASSEMBLY (for 14 Speakers)

  1. B241318E01
    Align the speaker with the door position pins labeled A.

  1. Install the rear No. 2 speaker with the 2 screws.

    NOTICE:
    Do not touch the cone of the speaker.


34. INSTALL NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY

  1. E198054
    Turn the light in the direction indicated by the arrow to install it.

  1. Attach the clamp.

  1. Connect the connector.


35. INSTALL REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH

  1. E198053
    Connect the connector.

  1. Attach the claw to install the light.


36. INSTALL REAR REFLEX REFLECTOR ASSEMBLY
  1. Attach the 2 claws to install the rear reflex reflector assembly.


37. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
  1. Attach the 2 claws to install the rear power window regulator switch assembly.


38. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

  1. B239678
    Attach the 3 claws to install the rear door inner glass weatherstrip as shown in the illustration.


39. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B239680
    Install the clamp to the door panel.

  1. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

  1. Connect each connector.

  1. B239608
    Attach the rear door trim board sub-assembly by attaching the 4 claws of the rear door inner glass weatherstrip as shown in the illustration.

  1. Attach the 9 clips and install the rear door trim board sub-assembly.

  1. Install the 3 screws.


40. INSTALL ASSIST GRIP COVER LH

  1. B241356
    Attach the 8 claws to install the assist grip cover.


41. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH

  1. B241355
    Attach the 3 claws to install the door inside handle bezel.


42. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


43. INITIALIZE POWER WINDOW CONTROL SYSTEM
  1. Initialize the power window control system (Click here).

← REASSEMBLY (Aug 2013 – Jul 2014)COMPONENTS (from Aug 2013) →