2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. REMOVE SPARK PLUG

  1. A222691
    Using a 16 mm spark plug wrench, remove the 4 spark plugs.


2. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
  1. Disconnect the oil pressure switch connector.

  1. A222346
    Using a 24 mm deep socket wrench, remove the oil pressure switch.


3. REMOVE KNOCK SENSOR

G037712E01
  1. Disconnect the knock sensor connector.

  1. Remove the bolt and knock sensor.


4. REMOVE ENGINE COOLANT TEMPERATURE SENSOR
  1. Disconnect the engine coolant temperature sensor connector.

  1. A102134
    Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor and gasket.


5. REMOVE OIL FILLER CAP SUB-ASSEMBLY

  1. A101281E01
    Remove the oil filler cap.

  1. Remove the gasket from the oil filler cap.


6. REMOVE PCV VALVE SUB-ASSEMBLY

  1. A223606
    Disconnect the PCV hose from the PCV valve.

  1. Using a 22 mm ball joint lock nut wrench, remove the PCV valve.


7. REMOVE CAMSHAFT POSITION SENSOR

G037910E01
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt and camshaft position sensor.


8. REMOVE CRANKSHAFT POSITION SENSOR

  1. A222453
    Disconnect the crankshaft position sensor connector and detach the wire harness clamp.

  1. G037914E02
    Remove the bolt and crankshaft position sensor.


9. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A223924
    Detach the 2 clamps and disconnect the 2 connectors.

  1. Remove the bolt and wiring harness clamp bracket.

  1. A224832
    Disconnect the camshaft timing oil control valve connector.

  1. Remove the bolt and camshaft timing oil control valve.

  1. Remove the O-ring from the camshaft timing oil control valve.


10. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A101292
    Remove the 19 bolts, 2 nuts, head cover and 2 gaskets.


11. REMOVE WATER INLET

  1. A222348
    Remove the bolt, 2 nuts, water inlet and gasket.


12. REMOVE THERMOSTAT

  1. A223318
    Remove the thermostat from the timing chain cover.


13. REMOVE CRANKSHAFT PULLEY

  1. A101288E02
    Using SST, hold the crankshaft pulley and loosen the pulley bolt until 2 or 3 threads are screwed into the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  
    Text in Illustration 
    *a
    Loosen
    *b
    Hold

  1. A101289E02
    Using SST and the pulley bolt, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)
    Text in Illustration 
    *a
    Loosen
    *b
    Hold

    HINT:
    Apply lubricant to the threads and end of SST.


14. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A224903
    Remove the drain plug and gasket.

  1. Remove the 18 bolts and 2 nuts.

  1. A101293
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.


15. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A265913
    Remove the bolt, 2 nuts, oil strainer and gasket.


16. REMOVE OIL PAN SUB-ASSEMBLY

  1. A273964E01
    Remove the 16 bolts and 2 nuts.

  1. A101296E02
    Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

  1. A101297E01
    Remove the O-ring.


17. REMOVE OIL PAN STUD BOLT

NOTICE:
If a stud bolt is deformed or its threads are damaged, replace it.


18. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. G035081E03
    Remove the 3 bolts and belt tensioner.


19. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A101298E01
    Remove the 19 bolts and 2 nuts shown in the illustration.

  1. A101299E02
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.

  1. A222350E02
    Remove the 3 O-rings.


20. REMOVE STRAIGHT SCREW PLUG

  1. A101979
    Using a 10 mm socket hexagon wrench, remove the straight screw plug.


21. REMOVE WATER PUMP ASSEMBLY

  1. A101301
    Remove the 8 bolts, water pump and gasket.


22. REMOVE TIMING CHAIN COVER OIL SEAL

  1. A101302E02
    Place the timing chain cover on wooden blocks.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Wooden Block

  1. Using a screwdriver pry out the oil seal.

    HINT:
    Tape the screwdriver tip before use.


23. REMOVE OIL PUMP RELIEF VALVE

  1. A086864E04
    Using a 27 mm socket wrench, remove the relief valve plug and gasket.

  1. Remove the valve spring and oil pump relief valve.


24. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A222396E01
    Temporarily install the crankshaft pulley bolt.

  1. Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

    Text in Illustration 
    *1
    Timing Mark
    *2
    Key

    HINT:
    If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.

  1. Remove the crankshaft pulley bolt.


25. REMOVE TIMING CHAIN GUIDE

  1. A101304
    Remove the 2 bolts, chain guide and O-ring.


26. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
A101303E07
  1. When the chain tensioner is removed, do not rotate the crankshaft.
  2. When the chain is removed and the camshaft needs to be rotated, rotate the crankshaft 90° to the right.

  1. Move the stopper plate upward to release the lock and push the plunger deep into the tensioner.

    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate

  1. Move the stopper plate downward to set the lock and insert a 3.0 mm (0.118 in.) diameter bar into the stopper plate hole.

  1. A101305
    Remove the bolt, nut, chain tensioner and gasket.


27. REMOVE CHAIN TENSIONER SLIPPER

  1. A101307E01
    Remove the bolt and tensioner slipper.


28. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A101306E01
    Remove the 2 bolts and vibration damper.


29. REMOVE CHAIN SUB-ASSEMBLY

30. REMOVE CRANKSHAFT TIMING GEAR

  1. A101308
    Remove the crankshaft timing gear from the crankshaft.


31. REMOVE CAMSHAFT BEARING CAP

  1. A170574E01
    Uniformly loosen and remove the 21 bearing cap bolts in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. A101310
    Remove the oil delivery pipe and O-ring from the bearing caps.

  1. A101311
    Remove the 9 bearing caps.

    HINT:
    Arrange the removed parts in the correct order.


32. REMOVE CAMSHAFT

A101312

33. REMOVE NO. 2 CAMSHAFT

A101313

34. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

  1. A101314
    Remove the 16 valve rocker arms from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


35. REMOVE CAMSHAFT TIMING SPROCKET

  1. A101317
    Mount the camshaft in a vise and remove the sprocket bolt and camshaft timing sprocket.

    NOTICE:
    Do not damage the camshaft.


36. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

  1. A062190E14
    Check the lock of the camshaft timing gear.

    1. Mount the camshaft in a vise and confirm that the camshaft timing gear is locked.

      Text in Illustration 
      *1
      Retard Side Path
      *2
      Advance Side Path
      *a
      Open
      *b
      Close
      V100144
      Rubber Piece
      V100145
      Vinyl Tape

      NOTICE:
      Do not damage the camshaft.

  1. Release the lock pin.

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

      HINT:
      2 advance side paths are provided in the groove of the camshaft. Plug one of the paths with a rubber piece.

    2. Break through the tape over the advance side path, and then break through the tape over the retard side path on the opposite side of the hole over the advance side path as shown in the illustration.

    3. A062191E14
      Apply compressed air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the two paths accessible through the holes in the tape.
      Text in Illustration 
      *1
      Retard Side Path
      *2
      Advance Side Path

      CAUTION:
      Some oil splashing will occur. Cover the paths with a piece of cloth.

    4. A062192E12
      Check that the camshaft timing gear revolves in the advance direction when reducing the air pressure applied to the retard side path.

      OK:
      Gear rotates in the advance direction.

      Text in Illustration 
      *1
      Retard Side Path
      *2
      Advance Side Path
      *a
      Decompress
      *b
      Hold Pressure

      HINT:
      This operation releases the lock pin which holds the timing gear in the most retarded position.

    5. When the camshaft timing gear reaches the most advanced position, release the air pressure from the retard side path and advance side path in that order.

      NOTICE:
      Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.

  1. Check for smooth rotation.

    1. Rotate the camshaft timing gear within its movable range several times, but do not turn it to the most retarded position. Check that the gear rotates smoothly.

      CAUTION:
      Do not use air pressure to perform the smooth operation check.

  1. Check the lock in the most retarded position.

    1. Confirm that the camshaft timing gear becomes locked at the most retarded position.


37. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

  1. A101318E03
    Remove the flange bolt and camshaft timing gear.
    Text in Illustration 
    *a
    Do Not Remove

    NOTICE:
    1. Be sure not to remove the other 3 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.


38. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. A101319E03
    Uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop the washers into the cylinder head.
    2. Head warpage or cracking could result from removing the bolts in the wrong order.


39. REMOVE CYLINDER HEAD GASKET
  1. Remove the cylinder head gasket from the cylinder block.


40. REMOVE NO. 2 CHAIN VIBRATION DAMPER

  1. A101320E04
    Move the stopper plate downward to release the lock and push the plunger deep into the tensioner.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate

  1. Move the stopper plate upward to set the lock and insert a hexagon wrench into the stopper plate hole.

  1. A101321E01
    Remove the bolt and chain vibration damper.


41. REMOVE NO. 3 CHAIN VIBRATION DAMPER

  1. A101322E01
    Remove the 2 bolts and chain vibration damper.


42. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A101323E01
    Remove the hexagon wrench from the tensioner assembly.

  1. Remove the nut and chain tensioner assembly.


43. REMOVE NO. 2 CHAIN SUB-ASSEMBLY

  1. A101324
    Remove the bolt, balance shaft drive gear shaft and balance shaft drive gear.

  1. Remove the crankshaft timing sprocket and chain.


44. REMOVE NO. 4 CHAIN VIBRATION DAMPER

  1. A101325E01
    Remove the 2 bolts and vibration damper.


45. REMOVE CRANKSHAFT PULLEY SET KEY

  1. A101326
    Remove the 2 pulley set keys from the crankshaft.


46. REMOVE OIL FILTER SUB-ASSEMBLY

  1. G038461E01
    Using SST, remove the oil filter.
    SST
    09228-07501  


47. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

  1. G037304E02
    Remove the 2 bolts and nut from the oil filter bracket.

  1. Remove the 2 screw plugs and 2 gaskets from the oil filter bracket.

  1. A101331E02
    Remove the oil filter bracket gasket and O-ring.
    Text in Illustration 
    *1
    O-Ring
    *2
    Oil Filter Bracket Gasket

  1. A101977E01
    Using a hexagon wrench, remove the oil filter bracket union.


48. REMOVE NO. 1 TAPER SCREW PLUG

  1. A101908E01
    Remove the taper screw plug from the cylinder block.


49. REMOVE ENGINE REAR OIL SEAL RETAINER

  1. A101335E02
    Remove the 6 bolts.

  1. Using a screwdriver, pry out the oil seal retainer.

    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.


50. REMOVE ENGINE REAR OIL SEAL

  1. A101332E02
    Place the oil seal retainer on wooden blocks.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Wooden Blocks

  1. Using a screwdriver and hammer, tap out the oil seal.

    HINT:
    Tape the screwdriver tip before use.


51. REMOVE VALVE STEM CAP

  1. A101315
    Remove the valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


52. REMOVE VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
  1. Keep the lash adjuster free from dirt and foreign objects.
  2. Only use clean engine oil.

  1. A101354E03
    Place the lash adjuster into a container full of new engine oil.
    Text in Illustration 
    *1
    Taper Part
    *2
    Plunger
    *3
    Low Pressure Chamber
    *4
    Check Ball
    *5
    High Pressure Chamber
    *a
    CORRECT
    *b
    INCORRECT

  1. Insert the tip of SST into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

    SST
    09276-75010  

  1. Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.

  1. After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

    OK:
    Plunger can be pressed 3 times.

    If the plunger can still be compressed after pressing it 3 times, replace the valve lash adjuster with a new one.


53. REMOVE OIL CONTROL VALVE FILTER

  1. A101413
    Using an 8 mm hexagon wrench, remove the screw plug.

  1. Remove the oil control valve filter and gasket.

← REMOVAL (from Aug 2014)INSPECTION (from Aug 2013) →