2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT CHAIN SUB-ASSEMBLY

  1. A101905E02
    Pull the chain with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.

  1. Using a vernier caliper, measure the length of 16 links.

    Maximum chain elongation:
    147.5 mm (5.81 in.)

    Text in Illustration 
    *1
    Measuring Area
    If the elongation is more than the maximum, replace the chain.

    NOTICE:
    Perform the measurement at 3 random places.


INSPECT NO. 2 CHAIN SUB-ASSEMBLY
  1. Pull the chain with a force of 147 N (15 kgf, 33.0 lbf).

  1. Using a vernier caliper, measure the length of 16 links.

    Maximum chain elongation:
    123.6 mm (4.87 in.)

    If the elongation is more than the maximum, replace the chain.

    NOTICE:
    Perform the measurement at 3 random places.


INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A097905E08
    Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate


INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A101971E02
    Move the stopper plate downward to release the lock. Push the plunger and check that it moves smoothly.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate


INSPECT CAMSHAFT TIMING SPROCKET

  1. A097906E04
    Measure the distance between the most worn out sprocket tip and the beginning of the worn area below the tip.

    Minimum distance:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    V100145
    Worn Area
    If the distance is less than the minimum, replace the sprocket.
    If the worn area is too small or difficult to distinguish from a normal area, perform the following 2 steps.

  1. Wrap the chain around the sprocket.

  1. Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    113.8 mm (4.48 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and sprocket.


INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

  1. A097907E05
    Measure the distance between the most worn out timing gear tip and the beginning of the worn area below the tip.

    Minimum distance:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    V100145
    Worn Area
    If the distance is less than the minimum, replace the timing gear.
    If the worn area is too small or difficult to distinguish from a normal area, perform the following 2 steps.

  1. Wrap the chain around the timing gear.

  1. Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    113.8 mm (4.48 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and timing gear.


INSPECT CRANKSHAFT TIMING GEAR

  1. A097908E04
    Measure the distance between the most worn out sprocket tip and the beginning of the worn area below the tip.

    Minimum distance:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    V100145
    Worn Area
    If the distance is less than the minimum, replace the sprocket.
    If the worn area is too small or difficult to distinguish from a normal area, perform the following 2 steps.

  1. Wrap the chain around the drive sprocket.

  1. Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    59.4 mm (2.34 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and sprocket.


INSPECT CHAIN TENSIONER SLIPPER

  1. A097909E05
    Using a vernier caliper, measure the tensioner slipper wear.

    Maximum wear:
    2.0 mm (0.0787 in.)

    Text in Illustration 
    *1
    Wear
    If the wear is more than the maximum, replace the tensioner slipper.


INSPECT NO. 1 CHAIN VIBRATION DAMPER

  1. A097910E05
    Using a vernier caliper, measure the vibration damper wear.

    Maximum wear:
    2.0 mm (0.0787 in.)

    Text in Illustration 
    *1
    Wear
    If the wear is more than the maximum, replace the vibration damper.


INSPECT TIMING CHAIN GUIDE

  1. A097911E06
    Using a vernier caliper, measure the chain guide wear.

    Maximum wear:
    0.5 mm (0.0197 in.)

    Text in Illustration 
    V100145
    Wear
    If the wear is more than the maximum, replace the timing chain guide.


INSPECT NO. 2 CRANKSHAFT TIMING SPROCKET
  1. Wrap the chain around the sprocket.

  1. A101907
    Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    96.7 mm (3.81 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and sprocket.


INSPECT BALANCE SHAFT DRIVE GEAR SUB-ASSEMBLY
  1. Wrap the chain around the sprocket.

  1. A101906
    Using a vernier caliper, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (with chain):
    75.9 mm (2.99 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and sprocket.


INSPECT NO. 2 CHAIN VIBRATION DAMPER

  1. A101337E02
    Using a vernier caliper, measure the vibration damper wear.

    Maximum wear:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *1
    Wear
    If the wear is more than the maximum, replace the vibration damper.


INSPECT NO. 3 CHAIN VIBRATION DAMPER

  1. A068741E04
    Using a vernier caliper, measure the vibration damper wear.

    Maximum wear:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *1
    Wear
    If the wear is more than the maximum, replace the vibration damper.


INSPECT NO. 4 CHAIN VIBRATION DAMPER

  1. A068742E04
    Using a vernier caliper, measure the vibration damper wear.

    Maximum wear:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *1
    Wear
    If the wear is more than the maximum, replace the vibration damper.


INSPECT CYLINDER HEAD SET BOLT

  1. A170594E01
    Using a vernier caliper, measure the diameter of the most elongated threads in the measuring area.

    Standard outside diameter:
    10.76 to 10.97 mm (0.424 to 0.432 in.)

    Minimum outside diameter:
    10.40 mm (0.409 in.)

    Distance:
    30 mm (1.18 in.)

    Text in Illustration 
    *1
    Measuring area
    *2
    Distance
    If a visual check reveals no excessively thin areas, check the center of the measuring area (see illustration) and find the area that has the smallest diameter.
    If the diameter is less than the minimum, replace the cylinder head bolt.


INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
  1. Keep the lash adjuster free from dirt and foreign objects.
  2. Only use clean engine oil.

  1. A101354E03
    Place the lash adjuster into a container full of new engine oil.
    Text in Illustration 
    *1
    Taper Part
    *2
    Plunger
    *3
    Low Pressure Chamber
    *4
    Check Ball
    *5
    High Pressure Chamber
    *a
    CORRECT
    *b
    INCORRECT

  1. Insert the tip of SST into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

    SST
    09276-75010  

  1. Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.

  1. After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

    OK:
    Plunger can be pressed 3 times.

    If the plunger can still be compressed after pressing it 3 times, replace the valve lash adjuster with a new one.


INSPECT CAMSHAFT
  1. Check the camshaft runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.00118 in.)

      If the circle runout is more than the maximum, replace the camshaft.

  1. Using a micrometer, measure the cam lobe height.

    Standard cam lobe height:
    42.855 to 42.955 mm (1.687 to 1.691 in.)

    Minimum cam lobe height:
    42.855 mm (1.687 in.)

    If the cam lobe height is less than the minimum, replace the camshaft.

  1. Using a micrometer, measure the journal diameter.

    Standard Journal Diameter:
    Item
    Specified Condition
    No. 1 journal
    35.949 to 35.965 mm (1.415 to 1.416 in.)
    Other journal
    26.959 to 26.975 mm (1.061 to 1.062 in.)

    If the journal diameter is not as specified, check the oil clearance.


INSPECT NO. 2 CAMSHAFT
  1. Check the camshaft runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.00118 in.)

      If the circle runout is more than the maximum, replace the camshaft.

  1. Using a micrometer, measure the cam lobe height.

    Standard cam lobe height:
    42.854 to 42.954 mm (1.687 to 1.691 in.)

    Minimum cam lobe height:
    42.854 mm (1.687 in.)

    If the cam lobe height is less than the minimum, replace the camshaft.

  1. Using a micrometer, measure the journal diameter.

    Standard Journal Diameter:
    Item
    Specified Condition
    No. 1 journal
    35.949 to 35.965 mm (1.415 to 1.416 in.)
    Other journal
    26.959 to 26.975 mm (1.061 to 1.062 in.)

    If the journal diameter is not as specified, check the oil clearance.


INSPECT CAMSHAFT THRUST CLEARANCE

  1. A101389
    Install the camshafts (Click here).

  1. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

    Standard thrust clearance:
    0.10 to 0.24 mm (0.00394 to 0.00945 in.)

    Maximum thrust clearance:
    0.26 mm (0.0102 in.)

    If the thrust clearance is more than the maximum, replace the cylinder head. If the thrust surface is damaged, replace the camshaft.


INSPECT CAMSHAFT OIL CLEARANCE
  1. Clean the bearing caps and camshaft journals.

  1. Place the camshafts on the cylinder head.

  1. A101390E02
    Lay a strip of Plastigage across each of the camshaft journals.
    Text in Illustration 
    *1
    Plastigage

  1. Install the bearing caps (Click here).

    NOTICE:
    Do not turn the camshafts.

  1. Remove the bearing caps (Click here).

  1. A101391E02
    Measure the Plastigage at its widest point.

    Standard Oil Clearance:
    Item
    Specified Condition
    No. 1 journal
    0.035 to 0.072 mm (0.00138 to 0.00283 in.)
    Other journals
    0.025 to 0.062 mm (0.000984 to 0.00244 in.)

    Maximum oil clearance:
    0.08 mm (0.00315 in.)

    Text in Illustration 
    *1
    Plastigage
    If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the cylinder head sub-assembly.

  1. Completely remove the Plastigage.


INSPECT EXHAUST MANIFOLD

  1. A222420
    Using a precision straightedge and feeler gauge, measure the warpage of the surface that contacts the cylinder head.

    Maximum warpage:
    0.7 mm (0.0276 in.)

    If the warpage is more than the maximum, replace the exhaust manifold.

← DISASSEMBLY (from Aug 2013)REASSEMBLY (from Aug 2013) →