2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REASSEMBLY

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL STUD BOLT

NOTICE:
If a stud bolt is deformed or its threads are damaged, replace it.


A170634E01
Text in Illustration 
*a
Cylinder Head Upper Side
*b
Intake Side
*c
Front Side
*d
Exhaust Side
  1. Using E6, E7 and E8 "TORX" socket wrenches, install the stud bolts.

    Torque:
    for stud bolt A:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }
    for stud bolt B:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
    for stud bolt C:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


2. INSTALL NO. 1 HEAD STRAIGHT SCREW PLUG

NOTICE:
A101373
If coolant leaks from the No. 1 head straight screw plug or the plug is corroded, replace it.

  1. Using a 10 mm hexagon wrench, install 3 new gaskets and the straight screw plugs.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


3. INSTALL NO. 2 HEAD STRAIGHT SCREW PLUG

NOTICE:
A101374
If coolant leaks from the No. 2 head straight screw plug or the plug is corroded, replace it.

  1. Using a 19 mm hexagon wrench, install a new gasket and the straight screw plug.

    Torque:
    140 N*m{ 1428 kgf*cm , 103 ft.*lbf }


4. INSTALL VALVE SPRING SEAT
  1. Install the 16 valve spring seats to the cylinder head.


5. INSTALL VALVE STEM OIL SEAL

  1. A101414E02
    Apply a light coat of engine oil to new oil seals.
    Text in Illustration 
    *1
    Gray
    *2
    Black
    *a
    Intake Side
    *b
    Exhaust Side

    NOTICE:
    Pay attention when installing the intake and exhaust oil seals. For example, installing an intake oil seal to the exhaust side or installing an exhaust oil seal to the intake side can cause installation problems later.

    HINT:
    The intake valve oil seals are gray and the exhaust valve oil seals are black.

  1. A101415E02
    Using SST, push in the 16 oil seals to install them.
    SST
    09201-41020  
    Text in Illustration 
    *1
    Valve Stem Oil Seal

    NOTICE:
    Failure to use SST will cause the seal to be damaged or improperly seated.


6. INSTALL INTAKE VALVE

  1. A101416E05
    Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.
    Text in Illustration 
    *a
    30 mm (1.18 in.) or more

  1. A332526E01
    Install the valve, inner compression spring and retainer to the cylinder head.
    Text in Illustration 
    *a
    Narrow
    *b
    Wide

    NOTICE:
    Install the same parts in the same combination to the original locations.

  1. A333831E01
    Using SST and wooden blocks, compress the inner compression spring and install the 2 valve spring retainer locks.
    SST
    09202-00020  
    09202-70020  

  1. A333836E01
    Using a 5 mm pin punch and plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.
    Text in Illustration 
    *1
    5 mm Pin Punch

    NOTICE:
    Do not damage the valve stem tip.


7. INSTALL EXHAUST VALVE

  1. A101419E05
    Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.
    Text in Illustration 
    *a
    30 mm (1.18 in.) or more

  1. A332527E01
    Install the valve, inner compression spring and retainer to the cylinder head.
    Text in Illustration 
    *a
    Narrow
    *b
    Wide

    NOTICE:
    Install the same parts in the same combination to the original locations.

  1. A333832E01
    Using SST and wooden blocks, compress the inner compression spring and install the 2 valve spring retainer locks.
    SST
    09202-00020  
    09202-70020  

  1. A333837E01
    Using a 5 mm pin punch and plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.
    Text in Illustration 
    *1
    5 mm Pin Punch

    NOTICE:
    Do not damage the valve stem tip.

← REASSEMBLY (Aug 2013 – Jul 2014)REPAIR (from Aug 2013) →