2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

INSTALLATION

Removal / installation · Vehicles built from Aug 2013


1. INSTALL REAR CRANKSHAFT OIL SEAL
  1. Apply MP grease to the lip of a new rear crankshaft oil seal.

  1. A244300E01
    Using SST and a hammer, tap in the oil seal until its surface is flush with the rear oil seal retainer edge.
    SST
    09518-36030  
    09950-70010   (09951-07200)

    NOTICE:
    1. The acceptable depth from the top of the oil seal retainer is 0 to 0.8mm (0 to 0.315 in.)
    1. Keep the lip free from foreign matter.
    1. Do not tap the oil seal at an angle.
    1. Make sure that the oil seal is properly installed.


2. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
  1. Clean the bolts and their holes.

  1. Apply adhesive to 2 or 3 threads at the end of each bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A225337E01
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. Install the flywheel to the crankshaft.

  1. A114803E01
    Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    178 N*m{ 1815 kgf*cm , 131 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installation.


3. INSTALL PUMP IMPELLER DRIVE PLATE (for Automatic Transmission)

  1. A225337E01
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. A271170E01
    Install the flywheel and ring gear, the pump impeller drive plate and the rear drive plate spacer to the crankshaft.
    Text in Illustration 
    *1
    Flywheel and Ring Gear
    *2
    Pump Impeller Drive Plate
    *3
    Rear Drive Plate Spacer
    *a
    Engine Side
    *b
    Transmission Side

    NOTICE:
    Align either hole in the pump impeller drive plate and either hole in the rear drive plate spacer with the knock pin of the flywheel and ring gear, and then install the flywheel and ring gear, the pump impeller drive plate and the rear drive plate spacer to the crankshaft.

    HINT:
    As the rear drive plate spacer and pump impeller drive plate are not reversible, be sure to install them in the direction shown in the illustration.

  1. Clean the bolts and their holes.

  1. A225158E01
    Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

    Torque:
    178 N*m{ 1815 kgf*cm , 131 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installation.


4. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

  1. C212716E02
    Insert SST into the clutch disc. Then insert SST (together with the clutch disc) into the flywheel to install the clutch disc.
    SST
    09301-00110  
    Text in Illustration 
    V100135
    Flywheel Side

    NOTICE:
    Be sure to install the clutch disc so that it is facing in the correct direction.


5. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

C215516E02
  1. Align the matchmarks on the clutch cover and flywheel.

    Text in Illustration 
    *a
    Matchmark

  1. Tighten the 6 bolts uniformly in the order shown in the illustration, starting with the bolt located near the knock pin on the top.

    SST
    09301-00110  

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    HINT:
    Move SST up and down, and right and left lightly after checking that the clutch disc assembly is in the center, and then tighten the bolts.


6. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

C217883E01
  1. Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

    SST
    09333-00013  

    Maximum non-alignment:
    0.5 mm (0.0196 in.)

    1. If the is alignment is more than the maximum, use SST to adjust the diaphragm spring tip alignment.


7. INSTALL MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
  1. Install the manual transmission (Click here).


8. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
  1. Install the automatic transmission (Click here).

← REMOVAL (from Aug 2013)COMPONENTS (from Aug 2013) →