2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0500 Vehicle Speed Sensor "A"

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Vehicles which are equipped with a manual transaxle detect the vehicle speed using the speed sensor. The speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transaxle output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.
A115899E12
P0500 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Drive the vehicle at 10 km/h (6.3 mph) or more
Conditions (a), (b) and (c) are met for 8 seconds or more (2 trip detection logic):
(a) Engine coolant temperature is higher than 70°C (158°F).
(b) Injection volume is 19 mm3/st or more.
(c) No speed signal is input to the ECM.
  1. Open or short in speedometer circuit
  2. Speedometer assembly
  3. ECM
Drive the vehicle at 10 km/h (6.3 mph) or more
Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):
(a) The fuel-cut operation is being performed.
(b) No speed signal is input to the ECM.
Related Data List 
DTC No.
Data List
P0500
Vehicle Speed

WIRING DIAGRAM

A160610E13

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

    HINT:
    The vehicle speed sensor is operating normally if the speedometer reading is normal.

    OK:
    The vehicle speed sensor is operating normally.



NG
Go to step 7
OK


2. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    OK:
    Vehicle speed displayed on tester and speedometer display are equal.



OK
Go to step 10

NG
Go to step 3
3. CHECK HARNESS AND CONNECTOR
A127854E29
  1. Disconnect the combination meter assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-32 (+S) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to combination meter assembly)

  1. Reconnect the combination meter assembly connector.



NG
Go to step 5
OK


4. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
A205820E06
  1. Move the shift lever to neutral.

  1. Jack up the vehicle.

  1. Check the voltage between the terminal of the combination meter assembly and the body ground while a wheel is turned slowly.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-32 (+S) - Body ground
    Ignition switch ON
    Voltage generated intermittently

    Text in Illustration 
    *a
    Component with harness connected
    (combination meter assembly)

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.

    Result 
    Result
    Proceed to
    OK
    A
    NG
    B



A
Go to step 6

B
Go to step 8
5. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
  1. Disconnect the combination meter assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    G6-32 (+S) - G58-30 (SPD)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    G6-32 (+S) or G58-30 (SPD) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the combination meter assembly connector.

  1. Reconnect the ECM connector.



NG
Go to step 9
OK


6. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 10
7. CHECK SPEEDOMETER CIRCUIT
  1. Check the speedometer circuit (Click here).

    HINT:
    Inspect the brake actuator assembly and speed sensor.



NEXT
Go to step 10
8. REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly (Click here).



NEXT
Go to step 10
9. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


10. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at 10 km/h (6.3 mph) or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the pending DTC is not output again.


NEXT

END


← P0489 Exhaust Gas Recirculation Control Circuit Low (+ P0490) (from Aug 2014)P0500 Vehicle Speed Sensor "A" (from Aug 2014) →