2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

TERMINALS OF ECU

System information · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
B235899E06
  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A-30 (BECU) - Body ground
    -
    Auxiliary battery power supply
    Ignition switch off
    11 to 14 V
    A-31 (ALTB) - Body ground
    -
    Auxiliary battery power supply
    Ignition switch off
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch off
    Below 1 V
    A-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    G63-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Install the main body ECU (multiplex network body ECU).

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G63-17 (GOSW) - Body ground
    LG - Body ground
    Glass hatch opener switch input
    Glass hatch open
    Below 1 V
    G63-17 (GOSW) - Body ground
    LG - Body ground
    Glass hatch opener switch input
    Ignition switch off, all doors closed and glass hatch closed
    Pulse generation (See waveform 1 or 2)
    2I-9 (GHRY) - Body ground*1
    B - Body ground
    Glass hatch opener relay output
    Ignition switch ON, glass hatch opener switch off
    Below 1 V
    2I-9 (GHRY) - Body ground*1
    B - Body ground
    Glass hatch opener relay output
    Ignition switch ON, glass hatch opener switch on
    11 to 14 V
    2H-9 (GHRY) - Body ground*2
    B - Body ground
    Glass hatch opener relay output
    Ignition switch ON, glass hatch opener switch off
    Below 1 V
    2H-9 (GHRY) - Body ground*2
    B - Body ground
    Glass hatch opener relay output
    Ignition switch ON, glass hatch opener switch on
    11 to 14 V
    1. *1: for LHD
    2. *2: for RHD
    If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.

  5. B199631E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G63-17 (GOSW) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Glass hatch closed

  6. B199632E01
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G63-17 (GOSW) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and glass hatch closed

← TERMINALS OF ECU (Aug 2013 – Jul 2014)DATA LIST / ACTIVE TEST (from Aug 2013) →