2013-2015 Land Cruiser Prado · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. REMOVE DRAIN PLUG SUB-ASSEMBLY

2. REMOVE BREATHER HOSE

C213735E01
  1. Remove the breather hose plug with the breather hose.

  1. Remove the breather hose from the breather hose plug.


3. REMOVE TRANSMISSION CONTROL SHAFT LEVER LH

D028070E02
  1. Remove the nut, spring washer and control shaft lever.


4. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C213712
  1. Using a screwdriver, bend the tab of the lock washer.

  1. Remove the nut and lock washer.

  1. Remove the bolt and park/neutral position switch.


5. REMOVE ATF TEMPERATURE SENSOR

G034862E01
  1. Remove the sensor.

  1. Remove the O-ring from the sensor.


6. REMOVE OIL COOLER TUBE UNION

G034863E01
  1. Remove the 2 tube unions.

  1. Remove the O-ring from each tube union.


7. REMOVE SPEED SENSOR NC0

Q003894E01
  1. Remove the bolt and sensor.

  1. Remove the O-ring from the sensor.


8. REMOVE SPEED SENSOR SP2

G035550E01
  1. Remove the bolt and sensor.

  1. Remove the O-ring from the sensor.


9. REMOVE AUTOMATIC TRANSMISSION HOUSING

C212450
  1. Remove the 6 bolts.

  1. Remove the transmission housing.


10. FIX TRANSMISSION CASE

AT05092E01
  1. Install the transmission case to an overhaul attachment.


11. REMOVE REAR TRANSFER ADAPTER

C212451
  1. Remove the 8 bolts.

  1. Remove the rear transfer adaptor.


12. REMOVE TRANSFER CASE ADAPTER REAR OIL SEAL

C212452
  1. Using a screwdriver, pry out the oil seal.


13. REMOVE TRANSFER CASE REAR ADAPTER OIL RECEIVER

C212453
  1. Using snap ring expander, remove the snap ring.

  1. Remove the transfer case rear adaptor oil receiver from the rear transfer adaptor.


14. REMOVE SENSOR ROTOR

C212454
  1. Using snap ring expander, remove the snap ring.

  1. C212455
    Remove the sensor rotor and key.


15. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

C212456

NOTICE:
Do not turn the transmission over as this will contaminate the valve body with foreign matter located at the bottom of the pan.

  1. Remove the 19 bolts.

  1. Q007487E04
    Insert the blade of an oil pan seal cutter between the transmission case and oil pan, and cut off the applied sealer.

    NOTICE:
    Be careful not to damage the oil pan and flange.

  1. Remove the pan from the transmission case.


16. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
  1. Remove the magnets and use them to collect steel particles.

  1. Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

    1. Steel (magnetic): bearing, gear and clutch plate wear.
    2. Brass (non-magnetic): bush wear.


17. REMOVE VALVE BODY OIL STRAINER ASSEMBLY
  1. Turn over the transmission.

  1. D028706E02
    Remove the 4 bolts and the valve body oil strainer from the valve body.

  1. Remove the 3 gaskets from the oil strainer.


18. REMOVE TRANSMISSION WIRE

C212457
  1. Remove the bolt and temperature sensor clamp, and disconnect the temperature sensor.

  1. Disconnect the 4 connectors from the shift solenoid valves.

  1. AT05066E04
    Remove the bolt and stopper plate from the case.

  1. Pull out the transmission wire from the transmission case to remove it.

  1. Remove the O-ring from the transmission wire connector.


19. REMOVE TRANSMISSION VALVE BODY ASSEMBLY

D029011E01
  1. Remove the 20 bolts and valve body.


20. REMOVE CHECK BALL BODY

AT04847E02
  1. Remove the check ball body and spring.

    Text in Illustration 
    *1
    Check Ball Body
    *2
    Spring


21. REMOVE B-2 ACCUMULATOR PISTON

D006514E01
  1. Apply compressed air to the oil hole to remove the B-2 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.


22. REMOVE C-2 ACCUMULATOR PISTON

D006514E02
  1. Apply compressed air to the oil hole to remove the C-2 accumulator piston and 2 springs.

  1. Remove the 2 O-rings from the piston.


23. REMOVE B-0 ACCUMULATOR PISTON

D006515E01
  1. Apply compressed air to the oil hole to remove the B-0 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.


24. REMOVE C-0 ACCUMULATOR PISTON

D006516E01
  1. Apply compressed air to the oil hole to remove the C-0 accumulator piston and 2 springs.

  1. Remove the O-ring from the piston.


25. REMOVE PARKING LOCK PAWL BRACKET

AT05103E01
  1. Remove the 3 bolts and bracket.


26. REMOVE PARKING LOCK ROD SUB-ASSEMBLY

AT05120E01
  1. Disconnect the parking lock rod from the manual valve lever to remove it.


27. REMOVE PARKING LOCK PAWL

Z006720E04
  1. Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.

    Text in Illustration 
    *1
    Parking Lock Pawl Shaft
    *2
    Lock Pawl
    *3
    Spring
    *4
    E-Ring

  1. Remove the E-ring from the shaft.


28. REMOVE MANUAL VALVE LEVER SHAFT

Z006721E04
  1. Using a hammer and screwdriver, cut off the spacer and remove it from the shaft.

    Text in Illustration 
    *1
    Spacer

  1. AT05105E01
    Using a pin punch and hammer, tap out the spring pin.

    HINT:
    Slowly drive out the spring pin so that it does not fall into the transmission case.

  1. Pull out the manual valve lever shaft through the case and remove the manual valve lever.


29. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

G034854E01
  1. Using a screwdriver, pry out the 2 oil seals.


30. REMOVE OIL PUMP ASSEMBLY

AT05122E02
  1. Stand the transmission.

  1. Remove the 7 bolts from the transmission case.

  1. AT07874E03
    Using SST, remove the oil pump.
    SST
    09610-20012  

  1. Remove the O-ring from the oil pump.

  1. AT08431E01
    Remove the bearing race from the oil pump.


31. REMOVE OVERDRIVE PLANETARY GEAR ASSEMBLY WITH OVERDRIVE DIRECT CLUTCH AND OVERDRIVE 1-WAY CLUTCH ASSEMBLY

C212458
  1. Remove the planetary gear with direct clutch and 1-way clutch from the transmission case.

  1. C212459E01
    Remove the bearing race and bearing.
    Text in Illustration 
    *1
    Bearing Race
    *2
    Bearing


32. INSPECT OVERDRIVE 1-WAY CLUTCH

AT08138E04
  1. Hold the overdrive direct clutch drum and turn the input shaft. Check that the input shaft can be turned clockwise freely and locks when turned counterclockwise.

    Text in Illustration 
    V100135
    Lock
    V100136
    Free


33. REMOVE OVERDRIVE DIRECT CLUTCH ASSEMBLY

C213736

34. REMOVE OVERDRIVE DIRECT CLUTCH DISC SET

C212481
  1. Using a screwdriver, pry out the snap ring from the overdrive direct clutch drum.

  1. Remove the flange, 2 discs and 2 plates.


35. INSPECT OVERDRIVE DIRECT CLUTCH DISC

C212466
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.


36. REMOVE OVERDRIVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

C212482E01
  1. Place SST on the spring retainer and compress the return spring with a press.

    SST
    09350-30020   (09350-07040)

    NOTICE:
    Do not deform the spring sheet. Stop compressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove.

  1. Using snap ring expander, remove the snap ring.

  1. Remove the clutch return spring.


37. INSPECT OVERDRIVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

C212467
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    15.8 mm (0.622 in.)

    If the length is not as specified, replace the overdrive clutch return spring sub-assembly.


38. REMOVE OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

AT03151E01
  1. Place the oil pump onto the torque converter clutch, and then place the overdrive direct clutch onto the oil pump.

  1. Hold the overdrive direct clutch piston by hand and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil pump to remove the overdrive direct clutch piston.

    HINT:
    If the piston is at an angle and cannot be removed, press down on the protruding side and apply compressed air again.

  1. Remove the 2 O-rings from the piston.


39. INSPECT OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

AT08150E01
  1. Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.
    If the result is not as specified, replace the overdrive direct clutch piston sub-assembly.


40. INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

C213737
  1. Using a dial indicator, measure the inside diameter of the clutch drum bushes.

    Maximum inside diameter:
    27.11 mm (1.07 in.)

    If the inside diameter is more than the maximum, replace the overdrive direct clutch drum sub-assembly.


41. REMOVE OVERDRIVE RETAINING PLATE

AT08135E01
  1. Using a screwdriver, pry out the snap ring.

  1. AT08146E01
    Remove the retaining plate.


42. REMOVE OVERDRIVE 1-WAY CLUTCH OUTER RACE WITH OVERDRIVE 1-WAY CLUTCH

AT08147E01

43. REMOVE OVERDRIVE 1-WAY CLUTCH

C212484
  1. Remove the overdrive 1-way clutch from the outer race.


44. REMOVE NO. 3 OVERDRIVE PLANETARY GEAR THRUST WASHER

C212485

45. INSPECT OVERDRIVE PLANETARY GEAR ASSEMBLY

AT08143E01
  1. Using a dial indicator, measure the inside diameter of the planetary gear bush.

    Maximum inside diameter:
    11.2 to 11.221 mm (0.441 to 0.442 in.)

    If the inside diameter is more than the maximum, replace the overdrive planetary gear assembly.

  1. AT04450E01
    Using a feeler gauge, measure the planetary pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00787 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    If the clearance is more than the maximum, replace the overdrive planetary gear assembly.


46. REMOVE OVERDRIVE PLANETARY RING GEAR WITH OVERDRIVE PLANETARY RING GEAR FLANGE

AT05146E01
  1. Remove the ring gear with the overdrive planetary ring gear flange from the transmission case.

  1. G035541E05
    Remove the bearing and bearing race from the overdrive planetary ring gear.
    Text in Illustration 
    *1
    Bearing
    *2
    Bearing Race


47. REMOVE OVERDRIVE PLANETARY RING GEAR FLANGE

AT08133E01
  1. Using a screwdriver, pry out the snap ring.

  1. AT08134E01
    Remove the ring gear flange from the overdrive planetary ring gear.


48. REMOVE OVERDRIVE BRAKE DISC SET

AT05109E01
  1. Using a screwdriver, pry out the snap ring.

  1. Remove the flange, 3 discs and 3 plates from the transmission case.


49. INSPECT OVERDRIVE BRAKE DISC

C212469
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.


50. INSPECT PISTON STROKE OF SECOND COAST BRAKE

AT05216E04
  1. Using a waterproof pen, place a mark on the 2nd coast brake piston rod as shown in the illustration.

    Text in Illustration 
    *1
    Piston Rod
    *2
    Mark

  1. AT05217E02
    Using SST, measure the piston stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).
    SST
    09240-00020  

    Standard piston stroke:
    1.5 to 3.0 mm (0.0591 to 0.118 in.)

    If the stroke is not as specified, inspect the brake band.


51. REMOVE OVERDRIVE SUPPORT SUB-ASSEMBLY

AT05148E02
  1. Remove the 2 bolts holding the overdrive brake assembly to the case.

  1. AT05249E03
    Using SST, remove the snap ring.
    SST
    09350-30020   (09350-07060)

  1. AT05211E03
    Using SST, remove the overdrive brake assembly.
    SST
    09350-30020   (09350-07020)

  1. AT05110E07
    Remove the bearing and bearing race from the overdrive brake.
    Text in Illustration 
    *1
    Bearing
    *2
    Bearing Race


52. INSPECT PISTON OPERATION OF OVERDRIVE BRAKE

AT08451E01
  1. Place the overdrive support assembly to the direct clutch assembly.

  1. AT08149E01
    Apply compressed air (392 kPa (4 kgf/cm2, 57 psi)) into the oil passage and check that the overdrive brake piston moves smoothly.


53. REMOVE OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

AT08444E01
  1. Place SST on the spring retainer and compress the return spring with a press.

    SST
    09350-30020   (09350-07030)

  1. Using a screwdriver, pry out the snap ring.

  1. Remove the brake return spring.


54. INSPECT OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

C212468
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.03 mm (0.671 in.)

    If the length is not as specified, replace the overdrive brake return spring sub-assembly.


55. REMOVE OVERDRIVE BRAKE PISTON

C212486
  1. Place the overdrive support onto the direct clutch assembly.

  1. Hold the overdrive brake piston so that it is not slanted, and apply compressed air (392 kPa (4 kgf/cm2, 57 psi)) into the passage to remove the overdrive brake piston.

  1. D001336E04
    Remove the 2 O-rings from the overdrive brake piston.
    Text in Illustration 
    *1
    O-Ring


56. REMOVE OVERDRIVE CLUTCH DRUM OIL SEAL RING

AT08160E01
  1. Remove the 2 oil seal rings from the overdrive support.

  1. AT08158E01
    Remove the clutch drum thrust washer from the overdrive support.


57. REMOVE SECOND COAST BRAKE PISTON

AT05127E01
  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07060)

  1. AT05280E01
    Apply compressed air to the oil hole to remove the second coast brake cover, piston assembly and spring.

  1. Remove the 2 O-rings from the cover.


58. REMOVE SECOND COAST BRAKE PISTON OIL SEAL RING

AT05418E01

59. REMOVE SECOND COAST BRAKE PISTON ROD

AT05260E01
  1. Firmly press the piston down to compress the compression spring.

  1. Remove the E-ring.

  1. D001299E05
    Remove the piston rod, washer plate and spring from the piston.
    Text in Illustration 
    *1
    Piston Rod
    *2
    Washer Plate
    *3
    Spring
    *4
    Piston


60. REMOVE DIRECT CLUTCH ASSEMBLY WITH FORWARD CLUTCH ASSEMBLY

AT05149E01
  1. Remove the direct clutch with the forward clutch from the case.

  1. AT03149E03
    Remove the 2 bearings and bearing race.
    Text in Illustration 
    *1
    Bearing
    *2
    Bearing Race


61. REMOVE FORWARD CLUTCH ASSEMBLY

AT05262E03
  1. Remove the forward clutch from the direct clutch.

  1. AT05259E07
    Remove the bearing, thrust washer and bearing race from the forward clutch.
    Text in Illustration 
    *1
    Bearing
    *2
    Thrust Washer
    *3
    Bearing Race


62. REMOVE DIRECT CLUTCH DISC SET

G037155E01
  1. Using a screwdriver, pry out the snap ring from the direct clutch drum.

  1. Remove the flange, 3 discs and 3 plates.


63. INSPECT DIRECT CLUTCH DISC

C212470
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.


64. REMOVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

AT08168E02
  1. Place SST on the spring retainer and compress the return spring with a press.

    SST
    09350-30020   (09350-07040)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. Remove the return spring.


65. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

C212471
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    21.32 mm (0.839 in.)

    If the length is not as specified, replace the direct clutch return spring sub-assembly.


66. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

G037157E01
  1. Place the direct clutch drum on the overdrive support.

  1. Hold the direct clutch piston and apply compressed air (196 kPa (2.0 kgf/cm2, 28.5 psi)) to the overdrive support to remove the direct clutch piston.

    HINT:
    Make sure the direct clutch piston is not tilted before applying compressed air.

  1. D001351E04
    Using a small screwdriver, remove the 2 O-rings from the piston.
    Text in Illustration 
    *1
    O-Ring


67. INSPECT DIRECT CLUTCH PISTON SUB-ASSEMBLY

D001424E01
  1. Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.


68. INSPECT DIRECT CLUTCH DRUM SUB-ASSEMBLY

D001352E01
  1. Using a dial indicator, measure the inside diameter of the clutch drum bush.

    Standard inside diameter:
    53.915 to 53.94 mm (2.123 to 2.124 in.)

    Maximum inside diameter:
    53.99 mm (2.13 in.)

    If the inside diameter is more than the maximum, replace the direct clutch drum sub-assembly.


69. FIX FORWARD CLUTCH ASSEMBLY

AT08165E01
  1. Place the overdrive support on wooden blocks or equivalent to prevent the forward clutch shaft from touching the work stand.

  1. Place the forward clutch on the overdrive support.


70. REMOVE FORWARD CLUTCH DISC SET

D001358E01
  1. Using a screwdriver, pry out the snap ring from the forward clutch drum.

  1. Remove the flange, 6 discs and 6 plates.

  1. AT08177E01
    Remove the cushion plate.


71. INSPECT FORWARD CLUTCH DISC

C212473
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.


72. REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

D001274E03
  1. Place SST on the spring retainer and compress the return spring with a press.

    SST
    09350-30020   (09350-07040)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. D001359E04
    Remove the piston return spring.


73. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

C212474
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    19.47 mm (0.767 in.)

    If the length is not as specified, replace the forward clutch return spring sub-assembly.


74. REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY

D025661E01
  1. Place the forward clutch drum onto the overdrive support.

  1. Hold the forward clutch piston by hand and apply compressed air (196 kPa (2.0 kgf/cm2, 28.5 psi)) to the overdrive support to remove the forward clutch piston.

  1. AT08179E01
    Remove the O-ring from the forward clutch drum.

  1. D001361E04
    Remove the 2 O-rings from the forward clutch piston.
    Text in Illustration 
    *1
    O-Ring


75. INSPECT FORWARD CLUTCH PISTON SUB-ASSEMBLY

D001424E01
  1. Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.


76. REMOVE INPUT SHAFT OIL SEAL RING

AT08180E01
  1. Remove the 3 oil seal rings from the forward clutch drum groove.


77. INSPECT INPUT SHAFT SUB-ASSEMBLY

AT08171E01
  1. Using a dial indicator, measure the inside diameter of the input shaft bush.

    Standard inside diameter:
    24.0 to 24.026 mm (0.945 to 0.946 in.)

    Maximum inside diameter:
    24.076 mm (0.948 in.)

    If the inside diameter is more than the maximum, replace the input shaft sub-assembly.


78. REMOVE SECOND COAST BRAKE BAND ASSEMBLY

AT05111E01
  1. Using a screwdriver, pry of the 2 E-rings from the pin, and pull out the pin.

  1. Q004030E01
    Remove the 2nd coast brake band from the case.


79. INSPECT SECOND COAST BRAKE BAND ASSEMBLY

D025701E04
Text in Illustration 
*1
Printed Number

NOTICE:
  1. If the lining of the brake band is peeled off or discolored, or if any part of the printed numbers are damaged, replace the brake band.
  2. When installing a new band, soak it in ATF for at least 15 minutes before installation.


80. REMOVE FRONT PLANETARY RING GEAR SUB-ASSEMBLY

AT05128E01
  1. Remove the planetary ring gear from the case.

  1. Q000841E05
    Remove the 2 bearing and bearing race from the planetary ring gear.
    Text in Illustration 
    *1
    Bearing
    *2
    Bearing Race

  1. Z005131E04
    Place the output shaft on wooden blocks or equivalent.
    Text in Illustration 
    *1
    Wooden Block


81. INSPECT FRONT PLANETARY RING GEAR SUB-ASSEMBLY

AT08187E01
  1. Using a dial indicator, measure the inside diameter of the planetary ring gear bush.

    Standard inside diameter:
    24.0 to 24.026 mm (0.945 to 0.946 in.)

    Maximum inside diameter:
    24.076 mm (0.948 in.)

    If the inside diameter is more than the maximum, replace the front planetary ring gear sub-assembly.


82. REMOVE FRONT PLANETARY GEAR ASSEMBLY

D029744E01
  1. Remove the bearing race from the planetary gear.

  1. D029740E03
    Using SST, remove the snap ring.
    SST
    09350-30020   (09350-07070)

  1. D029741E01
    Remove the planetary gear from the case.

  1. D029742E01
    Remove the bearing and bearing race from the planetary gear.


83. INSPECT FRONT PLANETARY GEAR ASSEMBLY

D029743E01
  1. Using a feeler gauge, measure the pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00787 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    If the clearance is more than the maximum, replace the front planetary gear assembly.


84. REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY WITH SUN GEAR INPUT DRUM AND NO. 1 1-WAY CLUTCH ASSEMBLY

Q000837E05
  1. Remove the sun gear with the sun gear input drum and 1-way clutch from the case.

  1. Remove the thrust washer.

    Text in Illustration 
    *1
    Thrust Washer


85. INSPECT NO. 1 1-WAY CLUTCH ASSEMBLY

AT08440E03
  1. Hold the planetary sun gear, and turn the 1-way clutch assembly. Check that the 1-way clutch hub can be turned clockwise freely and locks when turned counterclockwise.

    Text in Illustration 
    V100135
    Lock
    V100136
    Free


86. REMOVE NO. 1 1-WAY CLUTCH ASSEMBLY

AT08188E01

87. REMOVE NO. 1 1-WAY CLUTCH THRUST WASHER

AT01642E01

88. REMOVE SUN GEAR SHAFT OIL SEAL RING

AT08189E01
  1. Remove the 2 oil seal rings from the sun gear input drum.


89. REMOVE SUN GEAR INPUT DRUM

AT08190E02
  1. Place the planetary sun gear onto a wooden block or similar object.

  1. Using snap ring pliers, remove the snap ring.

  1. Remove the input drum from the planetary sun gear.


90. REMOVE SUN GEAR INPUT DRUM SHAFT SNAP RING

AT08182E01
  1. Using a screwdriver, pry off the snap ring from the planetary sun gear.


91. INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY

AT08337E01
  1. Using a dial indicator, measure the inside diameter of the planetary sun gear bushes.

    Standard inside diameter:
    27.00 to 27.026 mm (1.063 to 1.064 in.)

    Maximum inside diameter:
    27.076 mm (1.07 in.)

    If the inside diameter is more than the maximum, replace the planetary sun gear sub-assembly.


92. REMOVE SECOND BRAKE DISC SET

AT05476E01
  1. Using a screwdriver, pry out the snap ring.

  1. Remove the 2 flange, 5 discs and 4 plates.


93. REMOVE SECOND BRAKE PISTON SLEEVE

AT05279E01
  1. Using a screwdriver, remove the sleeve.


94. REMOVE OUTPUT SHAFT WITH REAR PLANETARY GEAR, NO. 2 1-WAY CLUTCH, FIRST AND REVERSE BRAKE DISC SET AND SECOND BRAKE DRUM

AT05460E03
  1. Using SST and a screwdriver, remove the snap ring.

    SST
    09350-30020   (09350-07060)

  1. AT05158E01
    Remove the output shaft with the rear planetary gear, No. 2 1-way clutch, first and reverse brake disc set and second brake drum from transmission case.

  1. AT05132E01
    Remove the thrust bearing from the transmission case.


95. REMOVE SECOND BRAKE DRUM SUB-ASSEMBLY

AT08183E01
  1. Remove the second brake drum.


96. REMOVE NO. 4 PLANETARY CARRIER THRUST WASHER

AT08184E01

97. INSPECT SECOND BRAKE PISTON

AT08439E01
  1. Check that the second brake piston moves smoothly when applying compressed air to and releasing low-pressure compressed air from the second brake drum.


98. REMOVE SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

AT08438E01
  1. Place SST on the spring retainer and compress the piston return spring with a press.

    SST
    09350-30020   (09350-07040)

  1. Using a snap ring expander, remove the snap ring.

    NOTICE:
    1. Do not deform the spring sheet. Stop compressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove.
    2. Do not expand the snap ring excessively.

  1. Remove the second brake piston return spring seat.

  1. AT08185E03
    Remove the piston return spring.


99. INSPECT SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C212479
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    16.05 mm (0.632 in.)

    If the length is not as specified, replace the second brake piston return spring sub-assembly.


100. REMOVE SECOND BRAKE PISTON

AT08196E01
  1. Hold the second brake piston by hand and apply compressed air to the 2nd brake drum to remove the 2nd brake piston.

    HINT:
    If the piston is at an angle and cannot be removed, press down on the protruding side and apply compressed air again.

  1. Remove the 2 O-rings from the piston.


101. REMOVE FIRST AND REVERSE BRAKE DISC SET

AT08208E01
  1. Remove the flange, 6 plates and 6 discs.


102. INSPECT FIRST AND REVERSE BRAKE DISC

C212463
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.


103. REMOVE OUTPUT SHAFT

AT08197E01

104. REMOVE PLANETARY OUTPUT SHAFT OIL SEAL RING

AT08198E01

105. REMOVE REAR PLANETARY RING GEAR

AT08199E01
  1. Remove the rear planetary gear from the planetary ring gear.

  1. C212461
    Remove the 2 bearing race and bearing from the planetary ring gear.

  1. AT08206E01
    Using a screwdriver, pry out the snap ring.

  1. AT08207E01
    Remove the planetary ring gear flange.


106. INSPECT NO. 2 1-WAY CLUTCH

AT08200E04
  1. Hold the planetary gear and turn the 1-way clutch inner race. Check that the 1-way clutch inner race can be turned counterclockwise freely and locks when turned clockwise.

    Text in Illustration 
    V100135
    Lock
    V100136
    Free


107. REMOVE NO. 2 1-WAY CLUTCH

AT08191E01
  1. Remove the 1-way clutch inner race from the planetary gear.

  1. AT08192E01
    Using a screwdriver, pry out the snap ring.

  1. AT08193E01
    Remove the 1-way clutch from the planetary gear.

  1. D028060E01
    Remove the No. 2 planetary carrier thrust washer from the planetary gear.

  1. D028061E01
    Remove the No. 1 planetary carrier thrust washer from the planetary gear.


108. INSPECT REAR PLANETARY GEAR ASSEMBLY

AT04459E01
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00797 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    If the clearance is more than the maximum, replace the rear planetary gear assembly.


109. REMOVE LEAF SPRING

AT05107E01

110. REMOVE BRAKE DRUM GASKET

AT04444E01

111. REMOVE FIRST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

AT08336E04
  1. Place SST on the first and reverse brake return spring and compress the brake return spring.

    SST
    09350-30020   (09350-07050)

  1. Using SST, remove the snap ring and brake return spring.

    SST
    09350-30020   (09350-07070)
    Text in Illustration 
    *1
    Snap Ring


112. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C212464
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    18.182 to 18.582 mm (0.716 to 0.732 in.)

    If the length is not as specified, replace the first and reverse brake return spring sub-assembly.


113. REMOVE NO. 2 FIRST AND REVERSE BRAKE PISTON

AT05375E01
  1. Hold the No. 2 first and reverse brake piston and apply compressed air to the transmission case to remove the brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the O-ring from the brake piston.


114. REMOVE BRAKE REACTION SLEEVE

AT08335E01
  1. Using SST, remove the sleeve.

    SST
    09350-30020   (09350-07080)

  1. Remove the O-rings from the sleeve.


115. REMOVE NO. 1 1ST AND REVERSE BRAKE PISTON

AT08334E01
  1. Using SST, remove the brake piston.

    SST
    09350-30020   (09350-07090)

  1. Remove the 2 O-rings from the brake piston.


116. INSPECT TRANSMISSION CASE BUSH

AT08224E01
  1. Using a cylinder gauge, measure the inside diameter of the transmission case rear bush.

    Standard inside diameter:
    38.113 to 38.138 mm (1.5005 to 1.5014 in.)

    Maximum inside diameter:
    38.19 mm (1.50 in.)

    If the inside diameter is more than the maximum, replace the automatic transmission case sub-assembly.

← COMPONENTS (from Aug 2013)INSPECTION (from Aug 2013) →