2013-2015 Land Cruiser Prado · Service Manual Drivetrain

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
  1. Remove the magnets and use them to collect steel particles.

  1. Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

    1. Steel (magnetic): bearing, gear and clutch plate wear.
    2. Brass (non-magnetic): bush wear.


INSPECT OVERDRIVE 1-WAY CLUTCH

AT08138E04
  1. Hold the overdrive direct clutch drum and turn the input shaft. Check that the input shaft can be turned clockwise freely and locks when turned counterclockwise.

    Text in Illustration 
    V100135
    Lock
    V100136
    Free


INSPECT OVERDRIVE DIRECT CLUTCH DISC

C212466
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.


INSPECT OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

C212467
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    15.8 mm (0.622 in.)

    If the length is not as specified, replace the overdrive clutch return spring sub-assembly.


INSPECT OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

AT08150E01
  1. Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.
    If the result is not as specified, replace the overdrive direct clutch piston sub-assembly.


INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

C213737
  1. Using a dial indicator, measure the inside diameter of the clutch drum bushes.

    Maximum inside diameter:
    27.11 mm (1.07 in.)

    If the inside diameter is more than the maximum, replace the overdrive direct clutch drum sub-assembly.


INSPECT OVERDRIVE PLANETARY GEAR ASSEMBLY

AT08143E01
  1. Using a dial indicator, measure the inside diameter of the planetary gear bush.

    Maximum inside diameter:
    11.2 to 11.221 mm (0.441 to 0.442 in.)

    If the inside diameter is more than the maximum, replace the overdrive planetary gear assembly.

  1. AT04450E01
    Using a feeler gauge, measure the planetary pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00787 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    If the clearance is more than the maximum, replace the overdrive planetary gear assembly.


INSPECT OVERDRIVE BRAKE DISC

C212469
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.


INSPECT PISTON OPERATION OF OVERDRIVE BRAKE

AT08451E01
  1. Place the overdrive support assembly to the direct clutch assembly.

  1. AT08149E01
    Apply compressed air (392 kPa (4 kgf/cm2, 57 psi)) into the oil passage and check that the overdrive brake piston moves smoothly.


INSPECT OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

C212468
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.03 mm (0.671 in.)

    If the length is not as specified, replace the overdrive brake return spring sub-assembly.


INSPECT DIRECT CLUTCH DISC

C212470
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.


INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

C212471
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    21.32 mm (0.839 in.)

    If the length is not as specified, replace the direct clutch return spring sub-assembly.


INSPECT DIRECT CLUTCH PISTON SUB-ASSEMBLY

D001424E01
  1. Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.


INSPECT DIRECT CLUTCH DRUM SUB-ASSEMBLY

D001352E01
  1. Using a dial indicator, measure the inside diameter of the clutch drum bush.

    Standard inside diameter:
    53.915 to 53.94 mm (2.123 to 2.124 in.)

    Maximum inside diameter:
    53.99 mm (2.13 in.)

    If the inside diameter is more than the maximum, replace the direct clutch drum sub-assembly.


INSPECT FORWARD CLUTCH DISC

C212473
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.


INSPECT FORWARD CLUTCH PISTON SUB-ASSEMBLY

D001424E01
  1. Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.


INSPECT INPUT SHAFT SUB-ASSEMBLY

AT08171E01
  1. Using a dial indicator, measure the inside diameter of the input shaft bush.

    Standard inside diameter:
    24.0 to 24.026 mm (0.945 to 0.946 in.)

    Maximum inside diameter:
    24.076 mm (0.948 in.)

    If the inside diameter is more than the maximum, replace the input shaft sub-assembly.


INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

C212474
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    19.47 mm (0.767 in.)

    If the length is not as specified, replace the forward clutch return spring sub-assembly.


INSPECT SECOND COAST BRAKE PISTON ROD

AT07705E01
  1. Check the piston rod length.

    HINT:
    There are 2 different standard lengths for the piston rod.

    Piston Rod Length:
    Groove Mark
    Length
    Without
    78.3 to 78.5 mm (3.08 to 3.09 in.)
    With
    79.8 to 80.0 mm (3.14 to 3.15 in.)

    If the length is not as specified, replace the rod with a new one even if the brake band works normally.


INSPECT SECOND COAST BRAKE BAND ASSEMBLY

D025701E04
Text in Illustration 
*1
Printed Number

NOTICE:
  1. If the lining of the brake band is peeled off or discolored, or if any part of the printed numbers are damaged, replace the brake band.
  2. When installing a new band, soak it in ATF for at least 15 minutes before installation.


INSPECT FRONT PLANETARY RING GEAR SUB-ASSEMBLY

AT08187E01
  1. Using a dial indicator, measure the inside diameter of the planetary ring gear bush.

    Standard inside diameter:
    24.0 to 24.026 mm (0.945 to 0.946 in.)

    Maximum inside diameter:
    24.076 mm (0.948 in.)

    If the inside diameter is more than the maximum, replace the front planetary ring gear sub-assembly.


INSPECT FRONT PLANETARY GEAR ASSEMBLY

D029743E01
  1. Using a feeler gauge, measure the pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00787 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    If the clearance is more than the maximum, replace the front planetary gear assembly.


INSPECT NO. 1 1-WAY CLUTCH ASSEMBLY

AT08440E03
  1. Hold the planetary sun gear, and turn the 1-way clutch assembly. Check that the 1-way clutch hub can be turned clockwise freely and locks when turned counterclockwise.

    Text in Illustration 
    V100135
    Lock
    V100136
    Free


INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY

AT08337E01
  1. Using a dial indicator, measure the inside diameter of the planetary sun gear bushes.

    Standard inside diameter:
    27.00 to 27.026 mm (1.063 to 1.064 in.)

    Maximum inside diameter:
    27.076 mm (1.07 in.)

    If the inside diameter is more than the maximum, replace the planetary sun gear sub-assembly.


INSPECT SECOND BRAKE PISTON

AT08439E01
  1. Check that the second brake piston moves smoothly when applying compressed air to and releasing low-pressure compressed air from the second brake drum.


INSPECT SECOND BRAKE DISC

C212478
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.


INSPECT SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C212479
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    16.05 mm (0.632 in.)

    If the length is not as specified, replace the second brake piston return spring sub-assembly.


INSPECT FIRST AND REVERSE BRAKE DISC

C212463
  1. Replace all the discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    When assembling new discs, soak them in ATF for at least 15 minutes before assembly.


INSPECT NO. 2 1-WAY CLUTCH

AT08200E04
  1. Hold the planetary gear and turn the 1-way clutch inner race. Check that the 1-way clutch inner race can be turned counterclockwise freely and locks when turned clockwise.

    Text in Illustration 
    V100135
    Lock
    V100136
    Free


INSPECT REAR PLANETARY GEAR ASSEMBLY

AT04459E01
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00797 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    If the clearance is more than the maximum, replace the rear planetary gear assembly.


INSPECT FIRST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C212464
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    18.182 to 18.582 mm (0.716 to 0.732 in.)

    If the length is not as specified, replace the first and reverse brake return spring sub-assembly.


INSPECT TRANSMISSION CASE BUSH

AT08224E01
  1. Using a cylinder gauge, measure the inside diameter of the transmission case rear bush.

    Standard inside diameter:
    38.113 to 38.138 mm (1.5005 to 1.5014 in.)

    Maximum inside diameter:
    38.19 mm (1.50 in.)

    If the inside diameter is more than the maximum, replace the automatic transmission case sub-assembly.


INSPECT PISTON OPERATION OF FIRST AND REVERSE BRAKE

AT05258E02
  1. Make sure the first and reverse brake pistons move smoothly when compressed air is applied into the transmission case.


INSPECT PISTON OPERATION OF SECOND COAST BRAKE

AT05216E04
  1. Place a mark on the 2nd coast brake piston rod.

    Text in Illustration 
    *1
    Mark
    *2
    Piston Rod

  1. AT05217E02
    Using SST, measure the stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).
    SST
    09240-00020  

    Standard piston stroke:
    1.5 to 3.0 mm (0.059 to 0.118 in.)

    If the stroke is not as specified, replace the brake band with a new one.


INSPECT OUTPUT SHAFT END PLAY

Z006796E01
  1. Using a dial indicator, measure the end play of the output shaft while moving it by hand.

    Standard end play:
    0.30 to 1.04 mm (0.0118 to 0.0409 in.)

    If the end play is not as specified, check for improper installation.

  1. Check that the output shaft rotates smoothly.

← DISASSEMBLY (from Aug 2013)REASSEMBLY (from Aug 2013) →