2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P2431 Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1

Diagnostic trouble codes · Vehicles built from Aug 2013

Also covers:

DESCRIPTION

The secondary air injection system consists of an air pump, the air switching valve, an air pressure sensor, the air injection control driver and the ECM. For a short time after cold engine starts, the secondary air injection system pumps secondary air to the exhaust port of the cylinder head to purify the exhaust emissions. The secondary air is supplied by the air pump and is pumped to the exhaust port through the air switching valve.
The air injection control driver drives the air switching valve and the air pump according to command signals transmitted by the ECM. The air pressure sensor detects the pressure in the secondary air passage when the secondary air injection system is ON and OFF, and transmits pressure signal to the ECM.
The air injection control driver is not only equipped to drive the pump and valve, but also with a diagnosis function to detect malfunctions in the secondary air injection system circuit.

HINT:
As a large current is required to drive the air pump and air switching valve, an air injection control driver is included in this system.

A121746E09
DTC No.
DTC Detection Condition
Trouble Area
P2431
Air pressure sensor indicates less than 45.63 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection logic)
  1. Air pressure sensor
  2. Open or short in air pressure sensor circuit
  3. ECM
P2432
While engine running, voltage output of air pressure sensor remains below 0.5 V (1 trip detection logic)
  1. Air pressure sensor
  2. Open or short in air pressure sensor circuit
  3. ECM
P2433
While engine running, voltage output of air pressure sensor remains above 4.5 V (1 trip detection logic)
  1. Air pressure sensor
  2. Open or short in air pressure sensor circuit
  3. ECM

MONITOR DESCRIPTION

A085160E21
The ECM monitors the pressure in the secondary air passage using the air pressure sensor located on the intake air connector.
If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the air pressure sensor or circuit and sets a DTC.

WIRING DIAGRAM

A237375E05

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (AIR PRESSURE SENSOR - ECM)
  1. Disconnect the air pressure sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C137-1 (E2) - C61-7 (E2G)
    Always
    Below 1 Ω
    C137-2 (AIP) - G59-1 (AIP)
    Always
    Below 1 Ω
    C137-3 (VC) - C62-6 (VC)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C137-2 (AIP) or G59-1 (AIP) - Body ground
    Always
    10 kΩ or higher
    C137-3 (VC) or C62-6 (VC) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air pressure sensor connector.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT ECM (SENSOR POWER SOURCE CIRCUIT)
A225616E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C61-7 (E2G) - Body ground
    Always
    Below 1 Ω

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C62-6 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
REPLACE ECM (Click here)
OK


3. READ DATA LIST (PUMP PRESSURE (ABSOLUTE))

  1. A273766
    Connect a pressure gauge to the air pressure sensor as shown in the illustration.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (absolute).

  1. Check that the pressure displayed on the intelligent tester fluctuates when applying the pressure to the air pressure sensor with the pressure gauge.

    OK:
    Pressure fluctuates in response to pressure applied with pressure gauge.

    HINT:
    The intelligent tester displays the air pump pressure (Air pump pressure (absolute)) as absolute pressure.



NG
REPLACE AIR PRESSURE SENSOR (Click here)
OK

REPLACE ECM (Click here)


← P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1) (+ P2238, P2239, P2252, P2253) (from Aug 2014)P2440 Secondary Air Injection System Switching Valve Stuck Open Bank1 (Aug 2013 – Jul 2014) →