2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTC P2195 (Click here).

HINT:
  1. Although the DTC titles refer to the oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the three way catalytic converter and located near the engine assembly.

DTC No.
DTC Detection Condition
Trouble Area
P2237
An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
P2238
One of the following conditions is met (2 trip detection logic):
  1. The air fuel ratio sensor output drops while the engine is running.
  2. The voltage at terminal A1A+ is 0.5 V or less.
  3. The voltage difference between terminals A1A+ and A1A- is 0.1 V or less.
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
P2239
The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
P2252
The A1A- voltage is 0.5 V or less (2 trip detection logic).
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
P2253
A1A- voltage is higher than 4.5 V (2 trip detection logic).
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the intelligent tester.
  1. Connect the intelligent tester to the DLC3.
  2. Start the engine.
  3. Turn the tester on.
  4. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  5. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
  6. Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  7. Monitor the output voltages of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.

HINT:
  1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
  2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1
(Air fuel ratio sensor)
+12.5%
Rich
Below 3.1 V
AFS Voltage B1S1
(Air fuel ratio sensor)
-12.5%
Lean
Higher than 3.4 V
O2S B1S2
(Heated oxygen sensor)
+12.5%
Rich
Higher than 0.55 V
O2S B1S2
(Heated oxygen sensor)
-12.5%
Lean
Below 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

Case
Air Fuel Ratio Sensor
Output Voltage
Heated Oxygen Sensor
Output Voltage
Main Suspected Trouble Area
1
A162605E23
A162598E15
-
2
A162596E18
A162598E15
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A162605E23
A162596E18
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
4
A162596E18
A162596E18
  1. Fuel pressure
  2. Gas leaks from exhaust system
    (air fuel ratio extremely lean or rich)
  1. Performing the Control the Injection Volume for A/F Sensor enables technicians to check and graph the output voltage of both the air fuel ratio sensor and heated oxygen sensor.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C56-3 (A1A+) - C63-7 (A1A+)
    Always
    Below 1 Ω
    C56-4 (A1A-) - C63-1 (A1A-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C56-3 (A1A+) or C63-7 (A1A+) - Body ground
    Always
    10 kΩ or higher
    C56-4 (A1A-) or C63-1 (A1A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the air fuel ratio sensor connector.A227661E01



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
OK


2. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Switch the ECM from normal mode to check mode (Click here).

  1. Drive the vehicle according to Confirmation Driving Pattern (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs (Pending DTCs).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P2237, P2238, P2239, P2252 or P2253 is output
    B



B
REPLACE ECM (Click here)
A

END


← P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1) (+ P2238, P2239, P2252, P2253) (Aug 2013 – Jul 2014)P2431 Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1 (+ P2432, P2433) (from Aug 2013) →