2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


2. REMOVE FRONT BUMPER LOWER COVER
  1. Remove the clip, 5 bolts and front bumper lower cover.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 engine under cover.


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A218364
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A245857E01

    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Vent Plug
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug


5. REMOVE NO. 3 ENGINE WIRE (for Cold Area Specification Vehicles)

  1. A218418
    Remove the 2 nuts from the battery terminal.

  1. Detach the 3 wire harness clamps.

  1. Remove the No. 3 engine wire from the fan shroud.


6. REMOVE NO. 1 AIR HOSE

  1. A218373
    Loosen the 2 clamps.

  1. Remove the No. 1 air hose from the inlet pipe and intercooler.


7. REMOVE INTERCOOLER AIR HOSE

  1. A224948
    Disconnect the No. 2 vacuum transmitting hose from the intercooler.

  1. A218374
    Loosen the 2 clamps.

  1. Remove the intercooler air hose from the intake pipe and intercooler.


8. REMOVE NO. 1 RADIATOR HOSE

A246596

9. REMOVE FAN SHROUD

  1. A218371
    Disconnect the No. 1 water by-pass hose and detach the 2 clamps from the fan shroud.

  1. Disconnect the No. 2 water by-pass hose from the radiator reservoir.

  1. Remove the 3 bolts and radiator reservoir.

  1. for Automatic Transmission:

    1. A218382
      Remove the inlet and outlet oil cooler hoses and detach the clamp from the fan shroud.

    2. Disconnect the 2 oil cooler hoses from the radiator.

  1. A224959
    Loosen the 4 nuts holding the fan with fluid coupling.

  1. Remove the fan and generator V belt (Click here).

  1. A218369
    Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts for the fan with fluid coupling, and then remove the shroud together with the fan with fluid coupling.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Detach the No. 2 water by-pass hose from the hose clamp on the fan shroud.

  1. A224943
    Remove the No. 2 water by-pass hose from the water inlet.

  1. Remove the fan pulley from the water pump.


10. REMOVE CRANKSHAFT POSITION SENSOR
  1. Detach the 2 wire harness clamps (A, B).

  1. Disconnect the crankshaft position sensor connector.

  1. Detach the crankshaft position sensor connector from the No. 1 vacuum transmitting pipe.

  1. Remove the clamp.

    NOTICE:
    1. Make sure that no portion of the clamp remains in the clamp installation hole. If there is any portion of the clamp remaining, remove it.
    2. Do not reuse the clamp.

  1. Remove the bolt and bracket (clamp).

  1. Remove the bolt and crankshaft position sensor.

  1. Detach the 2 wire harness clamps from the bracket (clamp).

    A307963E01

    Text in Illustration 
    *1
    Clamp
    *2
    Bracket (Clamp)
    *3
    Wire Harness Clamps (A)
    *4
    Wire Harness Clamps (B)

← COMPONENTS (from Aug 2013)INSPECTION (from Aug 2013) →