2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. REMOVE FRONT BUMPER LOWER COVER
  1. Remove the clip, 5 bolts and front bumper lower cover.


2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 engine under cover.


3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A218364
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A218365E01

    Text in IllustrationĀ 
    *1
    Radiator Reservoir
    *2
    Vent Plug
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug


4. REMOVE NO. 1 RADIATOR HOSE

A246596

5. REMOVE FAN SHROUD

  1. A218371
    Disconnect the No. 1 water by-pass hose and detach the 2 clamps from the fan shroud.

  1. Disconnect the No. 2 water by-pass hose from the radiator reservoir.

  1. Remove the 3 bolts and radiator reservoir.

  1. for Automatic Transmission:

    1. A218382
      Remove the inlet and outlet oil cooler hoses and detach the clamp from the fan shroud.

    2. Disconnect the 2 oil cooler hoses from the radiator.

  1. A224959
    Loosen the 4 nuts holding the fan with fluid coupling.

  1. Remove the fan and generator V belt (Click here).

  1. A218369
    Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts for the fan with fluid coupling, and then remove the shroud together with the fan with fluid coupling.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Detach the No. 2 water by-pass hose from the hose clamp on the fan shroud.

  1. A224943
    Remove the No. 2 water by-pass hose from the water inlet.

  1. Remove the fan pulley from the water pump.


6. REMOVE NO. 1 TIMING BELT COVER

  1. A015094E01
    Remove the 6 bolts, 6 washers and timing belt cover.


7. REMOVE TIMING BELT

  1. A070549E05
    Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
    Text in IllustrationĀ 
    *1
    Timing Mark

    HINT:
    If reusing the timing belt, place matchmarks on the timing belt so that it can be installed exactly as before.

  1. A070550E01
    Uniformly loosen and remove the 2 bolts and No. 1 timing belt tensioner.

  1. Remove the timing belt.

    HINT:
    A070551E02
    1. If turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise as shown in the illustration.
    2. When installing the timing belt, turn the camshaft to align the timing marks and then turn the crankshaft clockwise to align the timing marks.


8. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

NOTICE:
When inspecting the No. 1 timing belt idler, do not remove it unless absolutely necessary.

  1. Using a 10 mm hexagon wrench, remove the bolt, No. 1 timing belt idler and washer.

← COMPONENTS (from Aug 2013)INSPECTION (from Aug 2013) →