2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013

HINT:
  1. Thoroughly clean all parts to be assembled.
  2. Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.
  3. Replace all gaskets and oil seals with new ones.


1. INSTALL STUD BOLT

HINT:
If a stud bolt is deformed or the threads are damaged, replace it.

  1. Install the stud bolts.

    Torque:
    for stud bolt A and D:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    for stud bolt B:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    for stud bolt C:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }
    for stud bolt E:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


    A225490E01
    Text in Illustration 
    *1
    Stud Bolt A and B
    *2
    Stud Bolt C
    *3
    Stud Bolt D
    *4
    Stud Bolt E
    *a
    Front Side
    *b
    Intake Manifold Side
    *c
    Cylinder Head Cover Side
    *d
    Exhaust Manifold Side


2. INSTALL NO. 1 STRAIGHT SCREW PLUG

HINT:
If the No. 1 straight screw plug is corroded, replace it.

  1. Apply adhesive to the end of each No. 1 straight screw plug.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a 6 mm hexagon wrench, install the No. 1 straight screw plugs.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


    A060223E02
    Text in Illustration 
    *1
    Adhesive
    -
    -


3. INSTALL SEMICIRCULAR PLUG
  1. Remove any old seal packing (FIPG material).

  1. Apply seal packing to the semicircular plug as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. The semicircular plug must be installed within 3 minutes after applying the seal packing.
    2. Prevent seal packing from adhering to the camshaft thrust groove.


    A061555E02
    Text in Illustration 
    *1
    Adhesive
    -
    -

  1. Install the semicircular plug to the cylinder head.


4. INSTALL INTAKE VALVE STEM OIL SEAL

  1. A059919E01
    Using SST, push in a new oil seal.
    SST
    09201-41020  


5. INSTALL EXHAUST VALVE STEM OIL SEAL
  1. Using SST, push in a new oil seal.

    SST
    09201-41020  


6. INSTALL INTAKE VALVE

  1. A058114E01
    Install the valve, spring seat, compression spring and spring retainer.

  1. Using SST, compress the compression spring and install the 2 valve spring retainer locks to the valve stem.

    SST
    09202-70020  
    09202-00020  

  1. A060277E01
    Using a plastic-faced hammer, lightly tap the valve stem tip to assure a proper fit.

    NOTICE:
    Be careful not to damage the valve stem tip.


7. INSTALL EXHAUST VALVE

A058113E01
  1. Install the valve, spring seat, compression spring and spring retainer.

  1. Using SST, compress the compression spring and install the 2 valve spring retainer locks to the valve stem.

    SST
    09202-70020  
    09202-00020  

  1. A059917E01
    Using a plastic-faced hammer, lightly tap the valve stem tip to assure a proper fit.

    NOTICE:
    Be careful not to damage the valve stem tip.

← REPLACEMENT (from Aug 2013)REPAIR (from Aug 2013) →