2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. REMOVE OIL FILLER CAP SUB-ASSEMBLY

2. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.

  1. A060180E01
    Using a small screwdriver, remove the nozzle holder seal by prying the portion between the nozzle holder seal and the cutout part of the cylinder head cover.

  1. A223193
    Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


3. REMOVE INJECTOR ASSEMBLY

  1. A076779E04
    Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe.
    Text in Illustration 
    *1
    Union Bolt

    NOTICE:
    1. When removing the nozzle leakage pipe, place a cushion under the pipe.
    2. Be careful not to deform or scratch the union seal surface.
    3. After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A076780E02
    Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injectors.

    HINT:
    Arrange the injectors, No. 1 nozzle holder clamps, washers and bolts in the correct order.

  1. Remove the O-ring from each injector.

  1. Remove the 4 injection nozzle seats from the cylinder head.


4. REMOVE CAMSHAFT TIMING PULLEY

  1. A060182E01
    Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

    NOTICE:
    Make sure the timing belt is not installed when removing the bolt of camshaft timing pulley.

  1. Remove the camshaft timing pulley.


5. REMOVE NO. 2 TIMING BELT COVER

  1. A225464
    Remove the 4 bolts, nut and No. 2 timing belt cover.


6. REMOVE CYLINDER BLOCK INSULATOR

  1. A149941
    Remove the cylinder block insulator from the cylinder head.


7. REMOVE CAMSHAFT

  1. A060148E03
    Turn the camshaft with a wrench so that the key groove of the camshaft faces upward.
    Text in Illustration 
    *1
    Key Groove

  1. A060147E01
    Uniformly loosen the 15 bearing cap bolts in several passes in the sequence shown in the illustration.

  1. Remove the 15 bearing cap bolts, 5 bearing caps, oil seal and 2 camshafts.


8. REMOVE VALVE LIFTER
  1. Remove the valve lifters.

    HINT:
    Arrange the valve lifters in the correct order.


9. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. A059194E01
    Uniformly loosen the 18 cylinder head bolts in several passes in the sequence shown in the illustration. Then remove the 18 cylinder head bolts and 18 washers.

    NOTICE:
    Head warpage or cracking could result from removing bolts in the incorrect order.

  1. Remove the cylinder head from the dowels on the cylinder block and place the cylinder head on wooden blocks on a workbench.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.

    HINT:
    If the cylinder head is difficult to remove, use a screwdriver to pry between the cylinder head and block.


10. REMOVE CYLINDER HEAD GASKET

11. REMOVE WATER PUMP ASSEMBLY

  1. A225339
    Remove the 5 bolts, 2 nuts, water pump and gasket.


12. REMOVE TIMING GEAR COVER

NOTICE:
As the fuel supply pump is not installed, the injection gear is loose inside the timing gear case. Do not allow the injection gear to fall.

HINT:
To prevent the injection gear from falling, temporarily install the fuel supply pump.

  1. A239293
    Remove the 14 bolts and 2 nuts.

  1. A239294
    Pry the timing gear cover at the locations shown in the illustration and remove the timing gear cover.

    NOTICE:
    Be careful not to drop the injection gear.

  1. A239295
    Remove the 3 O-rings from the timing gear case.


13. REMOVE OIL CHECK VALVE SUB-ASSEMBLY

  1. A239305
    Using a 6 mm hexagon wrench, remove the bolt and oil check valve from the timing gear cover.


14. INSPECT OIL CHECK VALVE SUB-ASSEMBLY

  1. A231899E01
    Push the ball of the oil check valve to check if it is stuck.
    Text in Illustration 
    *1
    Ball
    If the check valve is stuck, replace the oil check valve sub-assembly.


15. REMOVE INJECTION GEAR

  1. A222329
    Secure the No. 2 idle sub gear to the No. 1 idle gear with a service bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    If the bolt hole of the No. 2 idle sub gear is not aligned with the bolt hole of the No. 1 idle gear, rotate the crankshaft counterclockwise to align the bolt holes. Then install the service bolt.

  1. A222330
    Remove the injection gear.


16. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A239296
    Remove the No. 1 crankshaft position sensor plate.


17. INSPECT BACKLASH OF CRANKSHAFT TIMING GEAR TO OIL PUMP GEAR

  1. A060171E01
    Using a dial indicator, measure the backlash.

    Standard gear backlash:
    0.02 to 0.15 mm (0.000787 to 0.00591 in.)

    Maximum gear backlash:
    0.2 mm (0.00787 in.)

    If the gear backlash is more than the maximum, replace the crankshaft timing gear or timing gear case assembly.


18. INSPECT BACKLASH OF CRANKSHAFT TIMING GEAR TO NO. 1 IDLE GEAR

  1. A060170E01
    Using a dial indicator, measure the backlash.

    Standard gear backlash:
    0.02 to 0.15 mm (0.000787 to 0.00591 in.)

    Maximum gear backlash:
    0.2 mm (0.00787 in.)

    If the gear backlash is more than the maximum, replace the crankshaft timing gear or No. 1 idle gear.


19. INSPECT NO. 1 IDLE GEAR THRUST CLEARANCE
  1. Install the timing gear case, No. 1 idle gear and camshaft timing gear.

  1. A060169E01
    Using a dial indicator, measure the thrust clearance.

    Standard thrust clearance:
    0.06 to 0.11 mm (0.00236 to 0.00433 in.)

    Maximum thrust clearance:
    0.3 mm (0.0118 in.)

    If the thrust clearance is more than the maximum, replace the idle gear thrust plate. If necessary, replace the No. 1 idle gear or No. 1 idle gear shaft.


20. REMOVE CRANKSHAFT TIMING GEAR

  1. A222332E01
    Using SST, remove the crankshaft timing gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)


21. INSPECT BACKLASH OF INJECTION GEAR TO NO. 1 IDLE GEAR
  1. Install the fuel supply pump with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A060158E01
    Using SST, install the injection gear with the nut.
    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }

  1. A060172E01
    Using a dial indicator, measure the backlash.

    Standard gear backlash:
    0.02 to 0.15 mm (0.000787 to 0.00591 in.)

    Maximum gear backlash:
    0.2 mm (0.00787 in.)

    If the gear backlash is more than the maximum, replace the injection gear or No. 1 idle gear.


22. REMOVE IDLE GEAR THRUST PLATE

  1. A238857
    Remove the 2 bolts and idle gear thrust plate.


23. REMOVE NO. 1 IDLE GEAR

  1. A238858
    Remove the No. 1 idle gear together with the No. 2 idle sub gear.


24. REMOVE NO. 1 IDLE GEAR SHAFT

  1. A238859
    Remove the No. 1 idle gear shaft.


25. INSPECT BACKLASH OF NO. 1 BALANCESHAFT TO OIL PUMP GEAR

  1. G036494E01
    Using a dial indicator, measure the backlash.

    Standard gear backlash:
    0.02 to 0.15 mm (0.000787 to 0.00591 in.)

    Maximum gear backlash:
    0.2 mm (0.00787 in.)

    If the gear backlash is more than the maximum, replace the No. 1 balanceshaft sub-assembly or timing gear case assembly.


26. INSPECT BACKLASH OF NO. 2 BALANCESHAFT TO INJECTION GEAR

  1. G036495E01
    Using a dial indicator, measure the backlash.

    Standard gear backlash:
    0.02 to 0.15 mm (0.000787 to 0.00591 in.)

    Maximum gear backlash:
    0.2 mm (0.00787 in.)

    If the gear backlash is more than the maximum, replace the No. 2 balanceshaft assembly or injection gear.

  1. A060158E01
    Using SST, remove the nut and injection gear.
    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 2 nuts and fuel supply pump.

  1. Remove the gears and timing gear case.


27. REMOVE NO. 1 IDLE SUB GEAR

  1. A069830E01
    Mount the No. 1 idle gear and No. 2 idle sub gear in a vise.

    NOTICE:
    Be careful not to damage the gears.

  1. A069831E02
    Using SST, turn the No. 1 idle sub gear clockwise and remove the service bolt.
    SST
    09960-10010   (09962-01000, 09963-00600)
    Text in Illustration 
    *1
    Service Bolt

  1. A069832E01
    Using snap ring pliers, remove the shaft snap ring.

  1. A069833E03
    Remove the wave washer, No. 1 idle sub gear and idle gear spring.
    Text in Illustration 
    *1
    Wave Washer
    *2
    No. 1 Idle Sub Gear
    *3
    Idle Gear Spring


28. REMOVE NO. 2 IDLE SUB GEAR

  1. A051322E01
    Turn the No. 1 idle gear over and set it in a vise.

    NOTICE:
    Be careful not a damage the gear.

  1. A069834E01
    Using snap ring pliers, remove the shaft snap ring.

  1. A069835E05
    Remove the wave washer, No. 2 idle sub gear and idle gear spring.
    Text in Illustration 
    *1
    Wave Washer
    *2
    No. 2 Idle Sub Gear
    *3
    Idle Gear Spring


29. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A225306
    Remove the 11 bolts and 2 nuts.

  1. A225310
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.


30. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A228657
    Remove the 2 nuts, oil strainer and gasket.


31. REMOVE OIL PAN SUB-ASSEMBLY

  1. A225307
    Remove the 22 bolts and 2 nuts.

  1. A225311E02
    Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    *a
    Pry

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.

  1. A225308
    Remove the gasket.


32. REMOVE TIMING GEAR CASE ASSEMBLY

  1. A239298
    Remove the union bolt and 8 bolts.

  1. A239299
    Pry the timing gear case at the location shown in the illustration and remove the gear case and gasket.

  1. A069840E03
    Remove the 2 O-rings.


33. INSPECT NO. 1 BALANCESHAFT THRUST CLEARANCE

  1. A051347E01
    Using a dial indicator, measure the thrust clearance while moving the No. 1 balanceshaft back and forth.

    Standard thrust clearance:
    0.065 to 0.140 mm (0.00256 to 0.00551 in.)

    Maximum thrust clearance:
    0.25 mm (0.00984 in.)

    If the thrust clearance is more than the maximum clearance, replace the balanceshaft thrust washer.
    If the thrust clearance is still more than the maximum clearance, replace the No. 1 balanceshaft sub-assembly.


34. REMOVE NO. 1 BALANCESHAFT SUB-ASSEMBLY

  1. A051332E01
    Remove the 2 bolts and balanceshaft.


35. REMOVE NO. 1 BALANCESHAFT DRIVEN GEAR

  1. A051333E01
    Mount the balanceshaft between aluminum plates in a vise.

    NOTICE:
    Be careful not to damage the balanceshaft.

  1. Remove the bolt, balanceshaft driven gear and balanceshaft thrust washer.


36. INSPECT NO. 2 BALANCESHAFT THRUST CLEARANCE

  1. A051347E01
    Using a dial indicator, measure the thrust clearance while moving the No. 2 balanceshaft back and forth.

    Standard thrust clearance:
    0.065 to 0.140 mm (0.00256 to 0.00551 in.)

    Maximum thrust clearance:
    0.25 mm (0.00984 in.)

    If the thrust clearance is more than the maximum clearance, replace the balanceshaft thrust washer.
    If the thrust clearance is still more than the maximum clearance, replace the No. 2 balanceshaft sub-assembly.


37. REMOVE NO. 2 BALANCESHAFT SUB-ASSEMBLY

  1. A051334E01
    Remove the 2 bolts and balanceshaft.


38. REMOVE NO. 2 BALANCESHAFT DRIVEN GEAR

  1. A051335E01
    Mount the balanceshaft between aluminum plates in a vise.

    NOTICE:
    Be careful not to damage the balanceshaft.

  1. Remove the bolt, balanceshaft driven gear and balanceshaft thrust washer.


39. REMOVE REAR ENGINE OIL SEAL RETAINER

A052295E01
  1. Remove the 5 bolts.

  1. Using a screwdriver, remove the rear engine oil seal retainer by prying between the rear engine oil seal retainer and cylinder block.


40. REMOVE FRONT CRANKSHAFT OIL SEAL

  1. A058121E01
    Using a screwdriver and hammer, tap out the oil seal.


41. REMOVE SUPPLY PUMP OIL SEAL

  1. A058117E01
    Using a screwdriver and hammer, tap out the oil seal.


42. REMOVE REAR CRANKSHAFT OIL SEAL

  1. A061819E01
    Using a screwdriver and hammer, tap out the oil seal.

← REMOVAL (from Aug 2014)INSPECTION (from Aug 2013) →