2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. INSTALL REAR CRANKSHAFT OIL SEAL

  1. A253830E01
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the rear engine oil seal retainer edge.
    SST
    09518-36030  
    09950-70010   (09951-07100)

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the oil seal at an angle.

  1. Apply MP grease to the lip of the oil seal.


2. INSTALL SUPPLY PUMP OIL SEAL

  1. A058118E02
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.
    SST
    09223-15020  
    09502-12010  
    09950-70010   (09951-07100)

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the oil seal at an angle.

  1. Apply MP grease to the lip of the oil seal.


3. INSTALL FRONT CRANKSHAFT OIL SEAL

  1. A058119E01
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.
    SST
    09214-76011  

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the oil seal at an angle.

  1. Apply MP grease to the lip of the oil seal.


4. INSTALL REAR ENGINE OIL SEAL RETAINER
  1. Remove any old seal packing (FIPG material) from the oil pan and cylinder block.

  1. A246541E01
    Apply seal packing to the places shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    4 mm (0.157 in.)

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    After applying seal packing, install the rear engine oil seal retainer within 3 minutes and tighten the bolts within 15 minutes.

  1. Install the rear engine oil seal retainer with the 5 bolts. Alternately tighten the 5 bolts in several passes.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


5. INSTALL NO. 2 BALANCESHAFT DRIVEN GEAR
  1. Mount the balanceshaft between aluminum plates in a vise.

    NOTICE:
    Be careful not to damage the balanceshaft.

  1. Align the balanceshaft knock pin with the knock pin hole. Then install the balanceshaft thrust washer and balanceshaft driven gear.

  1. Install the bolt.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }


6. INSTALL NO. 2 BALANCESHAFT SUB-ASSEMBLY
  1. Install the balanceshaft with the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


7. INSTALL NO. 1 BALANCESHAFT DRIVEN GEAR
  1. Mount the balanceshaft between aluminum plates in a vise.

    NOTICE:
    Be careful not to damage the balanceshaft.

  1. Align the balanceshaft knock pin with the knock pin hole. Then install the balanceshaft thrust washer and balanceshaft driven gear.

  1. Install the bolt.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }


8. INSTALL NO. 1 BALANCESHAFT SUB-ASSEMBLY
  1. Install the balanceshaft with the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


9. INSTALL TIMING GEAR CASE ASSEMBLY

  1. A069840E02
    Install 2 new O-rings to the cylinder block.
    Text in Illustration 
    *1
    New O-Ring

  1. A239302E01
    Install a new gasket to the groove of the timing gear case.
    Text in Illustration 
    *1
    New Gasket

  1. Remove any old seal packing (FIPG material).

  1. A239303E01
    Apply seal packing to the timing gear case as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    4 mm (0.157 in.)

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    After applying seal packing, install the timing gear case assembly within 3 minutes and tighten the bolts within 15 minutes.

  1. A247882
    Align the "2" marks of the No. 1 balanceshaft driven gear and oil pump drive gear.
    Text in Illustration 
    V100135
    Union Bolt
    V100136
    Bolt A
    V100137
    Bolt B

  1. Install the timing gear case with the union bolt and 8 bolts.

    Torque:
    for union bolt:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


10. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old seal packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder block, engine rear oil seal retainer and oil pan.

  1. Install a new gasket to the cylinder block.

  1. A225304E01
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    4 mm (0.157 in.)

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.

  1. Install the oil pan with the 22 bolts and 2 nuts.

    Torque:
    15 N*m{ 148 kgf*cm , 11 ft.*lbf }


11. INSTALL OIL STRAINER SUB-ASSEMBLY
  1. Install a new gasket and the oil strainer with the 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


12. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
  1. Remove any old seal packing (FIPG material).

  1. A225305E01
    Apply seal packing to the No. 2 oil pan as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    4 mm (0.157 in.)

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the No. 2 oil pan within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.

  1. Install the No. 2 oil pan with the 13 bolts and 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


13. INSTALL INJECTION GEAR
  1. Install a new O-ring and the fuel supply pump with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Temporarily install the injection gear with the nut.

    HINT:
    Fit the key (protrusion) of the fuel supply pump into the key slot of the injection gear.

  1. A069843E01
    Align the "3" marks of the No. 2 balanceshaft driven gear and injection gear.

  1. A069844E02
    Install a new O-ring to the injection gear.
    Text in Illustration 
    *1
    New O-Ring

  1. A069845E02
    Install the injection gear set nut.

  1. Using SST, tighten the set nut.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }


14. INSTALL CRANKSHAFT TIMING GEAR

A061827E01
  1. Position the crankshaft timing gear with timing mark 1 facing forward.

  1. Align the key groove of the crankshaft timing gear with the set key on the crankshaft.

  1. Using SST and a hammer, tap on the timing gear to install it.

    SST
    09223-00010  


15. INSTALL NO. 1 IDLE GEAR SHAFT

  1. A069846E01
    Apply a coat of engine oil to the No. 1 idle gear shaft.
    Text in Illustration 
    *1
    Engine Oil

  1. A060159E07
    Install the gear shaft as shown in the illustration.
    Text in Illustration 
    *1
    Oil Hole


16. INSTALL NO. 2 IDLE SUB GEAR

  1. A069847E03
    Mount the No. 1 idle gear in a vise.
    Text in Illustration 
    *1
    Cutout Mark

    NOTICE:
    Be careful not to damage the gear.

    HINT:
    Make sure the cutout mark of the idle gear faces down.

  1. A069848E03
    Install the idle gear spring.
    Text in Illustration 
    *1
    Wave Washer
    *2
    No. 2 Idle Sub Gear
    *3
    Idle Gear Spring

    HINT:
    Fit the pins on the gears between the spring ends.

  1. Install the No. 2 idle sub gear.

  1. Install the wave washer.

  1. A069834E01
    Using snap ring pliers, install the shaft snap ring.

  1. A069850E03
    Using SST, align the holes of the No. 1 idle gear and No. 2 idle sub gear by turning the No. 2 idle sub gear clockwise and install a service bolt.
    SST
    09960-10010   (09962-01000, 09963-00700)
    Text in Illustration 
    *1
    Service Bolt

  1. Remove the No. 1 idle gear from the vise and turn it upside down.


17. INSTALL NO. 1 IDLE SUB GEAR

  1. A069851E03
    Mount the No. 1 idle gear and No. 2 idle sub gear in a vise.
    Text in Illustration 
    *a
    Upward

    NOTICE:
    Be careful not to damage the gears.

  1. A069852E02
    Remove the service bolt.
    Text in Illustration 
    *1
    Service Bolt

  1. A069853E03
    Install the idle gear spring.
    Text in Illustration 
    *1
    Wave Washer
    *2
    No. 1 Idle Sub Gear
    *3
    Idle Gear Spring

    HINT:
    Fit the pins on the gears between the spring ends.

  1. Install the No. 1 idle sub gear.

  1. Install the wave washer.

  1. A069832E01
    Using snap ring pliers, install the shaft snap ring.

  1. A069854E03
    Using SST, align the holes of the No. 1 idle gear and No. 1 idle sub gear by turning the No. 1 idle sub gear clockwise, and install a service bolt.
    SST
    09960-10010   (09962-01000, 09963-00600)
    Text in Illustration 
    *1
    Service Bolt
    *a
    Upward


18. INSTALL NO. 1 IDLE GEAR

  1. G036757E04
    Align the "4" and "5" timing marks of the idle gear and crankshaft timing gear.
    Text in Illustration 
    *a
    Turn

  1. Using SST, turn the injection gear and align the "4" timing marks of the idle gear and injection gear, and then mesh the gears.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. A222334E02
    Position the idle gear thrust plate with the protrusion facing forward.
    Text in Illustration 
    *1
    Service Bolt

  1. Align the bolt holes and install the idle gear thrust plate with the 2 bolts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Remove the service bolt.


19. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
  1. Align the key groove of the No. 1 crankshaft position sensor plate with the set key.

  1. Install the No. 1 crankshaft position sensor plate with the cupped side facing outward.

    HINT:
    When replacing the No. 1 crankshaft position sensor plate, perform "Crank Time Compensation Reset" (Click here).


20. INSTALL OIL CHECK VALVE SUB-ASSEMBLY
  1. Using a 6 mm hexagon wrench, install the oil check valve with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


21. INSTALL TIMING GEAR COVER
  1. Remove any old seal packing (FIPG material).

  1. A239329E01
    Apply seal packing to the timing gear cover as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    4 mm (0.157 in.)

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    After applying seal packing, install the timing gear cover within 3 minutes and tighten the bolts within 15 minutes.

  1. A239295E01
    Install 3 new O-rings to the timing gear case.
    Text in Illustration 
    *1
    New O-Ring

  1. Install the timing gear cover with the 14 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. A248630
    Remove the screw plug and gasket.

  1. Pour approximately 50 cc (3.05 cu. in.) of engine oil into the oil pump.

  1. Install a new gasket and the screw plug.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


22. INSTALL WATER PUMP ASSEMBLY
  1. Install a new gasket and the water pump with the 5 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


23. INSTALL CYLINDER HEAD GASKET

  1. A060285E02
    Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.
    Text in Illustration 
    *1
    Measuring Tip
    *2
    Protrusion

  1. A058134E02
    Measure the piston protrusion of each cylinder at 2 points as shown in the illustration.
    Text in Illustration 
    *1
    Measuring Point

  1. For the piston protrusion value of each cylinder, use the average of the 2 measurements of each cylinder.

    Piston protrusion:
    0.005 to 0.255 mm (0.000197 to 0.0100 in.)

    HINT:
    After installing the piston and connecting rod assembly, if the protrusion is not as specified, remove the piston and connecting rod assembly and reinstall them.

  1. A060174E02
    Select a new cylinder head gasket.
    Text in Illustration 
    *1
    Cutout Mark
    V100135
    Front

    HINT:
    New cylinder head gaskets are available in 5 sizes, and are marked A, B, C, D or E.

    New Cylinder Head Gasket Thickness:
    Mark
    Specified Condition
    A
    0.80 to 0.90 mm (0.0315 to 0.0354 in.)
    B
    0.85 to 0.95 mm (0.0335 to 0.0374 in.)
    C
    0.90 to 1.00 mm (0.0354 to 0.0394 in.)
    D
    0.95 to 1.05 mm (0.0374 to 0.0413 in.)
    E
    1.00 to 1.10 mm (0.0394 to 0.0433 in.)


    1. Select the largest piston protrusion value from the measurements made. Then select a new gasket according to the table below.

      Gasket Size:
      Item
      Specified Condition
      Piston protrusion
      0.005 to 0.054 mm (0.000197 to 0.00213 in.)
      0.055 to 0.104 mm (0.00217 to 0.00409 in.)
      0.105 to 0.154 mm (0.00413 to 0.00606 in.)
      0.155 to 0.204 mm (0.00610 to 0.00803 in.)
      0.205 to 0.255 mm (0.00807 to 0.0100 in.)
      Gasket to be used
      A
      B
      C
      D
      E

  1. A060144E02
    Place the cylinder head gasket on the cylinder block.
    Text in Illustration 
    V100135
    Front

    NOTICE:
    Make sure the gasket is installed facing the proper direction.


24. INSTALL CYLINDER HEAD SUB-ASSEMBLY

A060284E01

HINT:
  1. The cylinder head bolts are tightened in 3 progressive steps.
  2. If any bolt is broken or deformed, replace it (Click here).

  1. Place the cylinder head on the cylinder head gasket.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Install the 18 washers with the 18 cylinder head bolts, and uniformly tighten the bolts in several passes in the sequence shown in the illustration.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

    Standard Bolt Length:
    Item
    Specified Condition
    A
    110 mm (4.33 in.)
    B
    167 mm (6.57 in.)

    If any one the cylinder head bolts does not meet the torque specification, replace it.

  1. A060141E03
    Mark the front of each cylinder head bolt with paint.
    *1
    Painted Mark
    *a
    Front

  1. Further tighten the cylinder head bolts by 90° in the sequence shown in the illustration above.

  1. Tighten the cylinder head bolts by an additional 90°.

  1. Check that the painted marks are now facing rearward.


25. INSTALL VALVE LIFTER
  1. Install the valve lifters.

  1. Check that each valve lifter rotates smoothly by hand.


26. INSTALL CAMSHAFT

  1. G036616E02
    Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.
    Text in Illustration 
    *1
    Key

    HINT:
    Set the No. 1 cylinder to 90° BTDC/compression to prevent the top of the piston from hitting against the valve head.

  1. A060149E04
    Install the camshaft.

    1. Apply engine oil to the thrust portion of the camshaft.

    2. Place the camshaft on the cylinder head with the key groove facing upward.

      Text in Illustration 
      *1
      Key Groove
      *a
      Upward

    3. A060150E01
      Align the timing marks (1-dot marks) of the camshaft drive and driven main gears and set the No. 2 camshaft in place.

  1. Remove any old seal packing (FIPG material) from the camshaft bearing cap.

  1. A060283E05
    Apply seal packing to the specified areas shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    4 mm (0.157 in.)

    Text in Illustration 
    *1
    Seal Packing
    *2
    Oil Passage

    NOTICE:
    1. Do not allow seal packing to contact the oil passage of the bearing cap.
    2. After applying seal packing, install the camshaft bearing caps within 3 minutes and tighten the bolts within 15 minutes.
    3. Do not start the engine for at least 2 hours after installation.

  1. A060146E01
    Install the 5 bearing caps to their proper locations.

  1. A060147E02
    Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. Install and uniformly tighten the 15 bearing cap bolts in several passes in the sequence shown in the illustration.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. A060145E01
    Install a new camshaft oil seal.

    1. Apply MP grease to the lip of a new oil seal.

    2. Using SST and a hammer, tap in the oil seal until its surface is flush with the surfaces of the camshaft bearing cap and cylinder head.

      SST
      09608-06041  


27. INSTALL CYLINDER BLOCK INSULATOR
  1. Install the cylinder block insulator to the cylinder head.


28. INSTALL NO. 2 TIMING BELT COVER

  1. A060279E02
    Apply seal packing (FIPG) to the specified areas shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    After applying seal packing, install the No. 2 timing belt cover within 3 minutes and tighten the bolts and nut within 15 minutes.

  1. Install the No. 2 timing belt cover with the 4 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


29. INSTALL CAMSHAFT TIMING PULLEY
  1. Install the camshaft timing pulley.

  1. Install the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

    Torque:
    98 N*m{ 1000 kgf*cm , 72 ft.*lbf }


30. INSPECT AND ADJUST VALVE CLEARANCE
(Click here)

31. INSTALL INJECTOR ASSEMBLY

NOTICE:
Be sure to install the injector, No. 1 nozzle holder clamp, washer and bolt in their original positions.

  1. A239583
    Install 4 new injection nozzle seats to the cylinder head.

  1. Apply a small amount of clean engine oil to 4 new O-rings.

  1. A231908E01
    Install one of the O-rings to each injector as shown in the illustration.
    Text in Illustration 
    *1
    New O-Ring

  1. Insert the 4 injectors into the cylinder head.

    NOTICE:
    1. Insert the injector until it touches the injection nozzle seat surface.
    2. After installing the injector to the cylinder head, the O-ring may prevent the injector from being fully seated. If so, pull out the injector and reinstall it.
    3. Always reinstall an injector to the same place it was removed from.

  1. For an injector that has been replaced with a new injector, register the injector compensation code (Click here).

  1. A100922E02
    Temporarily install 4 new washers and the 4 No. 1 nozzle holder clamps with the 4 bolts.
    Text in Illustration 
    *1
    Washer
    *a
    Downward

    HINT:
    Apply a small amount of engine oil to the threads and under the heads of the clamp bolts.


    NOTICE:
    G037744E05
    1. The fork portion of the No. 1 nozzle holder clamp must be set on the injector.
    2. Before tightening the bolts, check that the No. 1 nozzle holder clamp is set properly.
    3. When installing the clamp bolts, first tighten them by hand until they cannot be turned further. Then, tighten the bolts to the specified torque in a following step.
    4. When tightening the bolts, be careful so as not to tilt the bolt or clamp.
    5. Do not reuse the washer.
    6. If the nozzle leakage pipe is accidentally tightened beyond the torque specification, it must be replaced.
      Text in Illustration 
      *1
      No. 1 Nozzle Holder Clamp

  1. Temporarily install the 4 injection pipes with the union nuts.

    HINT:
    To position the injectors, loosely tighten the union nut.

  1. A062123E01
    Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces.
    If scratches or dents are present, replace the nozzle leakage pipe.

  1. A076602E02
    Set the nozzle leakage pipe and 5 new gaskets in place.

  1. Apply a small amount of oil to the 4 injector hollow screws and union bolt.

  1. Temporarily install the nozzle leakage pipe with the 4 injector hollow screws and union bolt.

  1. Tighten the 4 nozzle holder clamp bolts.

    Torque:
    22 N*m{ 220 kgf*cm , 16 ft.*lbf }

  1. A076779E05
    Tighten the 4 injector hollow screws in order from 1 to 4.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    Text in Illustration 
    *1
    Union Bolt

    NOTICE:
    If an injector hollow screw is accidentally tightened beyond the torque specification, it must be replaced.

  1. Tighten the union bolt.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    If the union bolt is accidentally tightened beyond the torque specification, it must be replaced.

  1. Remove the 4 injection pipes.


32. INSPECT FOR FUEL LEAK

  1. A239627E01
    Check that there are no leaks from the nozzle leakage pipe connection.

    1. Install a new gasket and the and No. 2 nozzle leakage pipe to the cylinder head with SST (check valve).

      Part No.:
      23762-27010 (No. 2 nozzle leakage pipe)
      90904-30012 (Gasket)

      SST
      09280-00010  

      Torque:
      21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    2. Apply a small amount of soapy water (or other fluid for detecting fuel leakage) on the nozzle leakage pipe connection.

    3. A239628E01
      Install SST (turbocharger pressure gauge) to the fuel return side of the nozzle leakage pipe, maintain 100 kPa (1.0 kgf/cm2, 15 psi) of pressure for 60 seconds and check that no bubbles form.
      SST
      09992-00242  

    4. After checking for fuel leaks, wipe off the soapy water from the nozzle leakage pipe connection.

    5. Remove SST, the No. 2 nozzle leakage pipe and gasket.

      NOTICE:
      Never reinstall the disassembled union bolt to the engine.


33. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A289512E01
    Install 4 new No. 3 cylinder head cover gaskets to the cylinder head cover in the directions shown in the illustration.
    Text in Illustration 
    *1
    No. 3 Cylinder Head Cover Gasket
    *2
    Cylinder Head Cover

    NOTICE:
    1. Do not install the No. 3 cylinder head cover gaskets at an angle.
    2. Check that there is no foreign matter at the installation location of the No. 3 cylinder head cover gaskets.

  1. Remove any old seal packing (FIPG material) from the cylinder head.

  1. A060179E06
    Apply seal packing to the areas shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Text in Illustration 
    V100155
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing the cylinder head cover.

  1. Install a new cylinder head cover gasket to the cylinder head cover.

  1. A223193E01
    Temporarily install the cover with the 10 bolts and 2 nuts in the order shown in the illustration. Then, tighten the 10 bolts and 2 nuts in the order shown in the illustration in 2 progressive steps.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install 4 new nozzle holder seals.


34. INSTALL OIL FILLER CAP SUB-ASSEMBLY
← INSPECTION (from Aug 2013)INSTALLATION (Aug 2013 – Jul 2014) →