2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

DTC CHECK / CLEAR

Troubleshooting · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


CHECK DTC (CHECK USING GTS)
  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

  5. Check for DTCs, and then write them down.

  6. Check the details of the DTC(s).


CLEAR DTC (CLEAR USING GTS)
  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

  5. Clear the DTCs.


START DIAGNOSTIC MODE

HINT:
  1. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
  2. After the ignition switch is turned to ON, check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.

  1. Start the engine.

  2. While pressing and holding the "AUDIO", "MEDIA" or "CAR" switch of the multi-display assembly, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.

  3. E286247E01
    Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD


FAILURE DIAGNOSIS

  1. E278177
    The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.


SYSTEM CHECK

  1. E287209
    The "System Check Mode" screen will be displayed by selecting "System Check" on the "Failure Diagnosis" screen.


CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)

  1. E287210E01
    System check mode screen description
    Screen Description 
    Display
    Content
    *a: Device Name List No. 1
    1. Device Name List No. 1 displays some of the devices that make up the audio and visual system.
    2. The names of the components from Device Name List No. 1 are shown in the following table.
    *b: Check Result
    Result codes for all devices are displayed.
    *c: Memory Clear
    1. Present and history DTCs and registered connected device names are cleared.
    2. Select "Memory CLR" for 3 seconds.
    *d: Recheck
    1. A system check will be performed again after the memory is cleared.
    2. "Recheck" will dim during a system check.
    *e: Device Name List No. 2
    1. Device Name List No. 2 displays some of the devices that make up the audio and visual system.
    2. The names of the components from Device Name List No. 2 are shown in the following table.
    *b: Device Name List No. 1 Description 
    Name
    Component
    Connection Method
    DA
    Radio and display receiver assembly
    -
    AMP
    Stereo component amplifier assembly*1
    Communication line for AVC-LAN
    Rr-TV
    Television display assembly*2
    Communication line for AVC-LAN
    CAMERA-C
    Parking assist ECU*3
    Communication line for AVC-LAN
    1. *1: for 9 Speakers
    2. *2: w/ Rear Seat Entertainment System
    3. *3: w/ Side Monitor System
    *c: Check Result Description 
    Result
    Meaning
    Action
    OK
    The device does not respond with a DTC.
    -
    DETAIL
    The device responds with a DTC.
    Look up the DTC in "Unit Check Mode".
    NCON
    The device was previously present, but does not respond in diagnostic mode.
    - Check power supply wire harness of the device.
    - Check the AVC-LAN of the device.
    NRES
    The device responds in diagnostic mode, but gives no DTC information.
    - Check power supply wire harness of the device.
    - Check the AVC-LAN of the device.
    *e: Device Name List No. 2 Description 
    Name
    Component
    Connection Method
    AUX/VTR
    No. 1 stereo jack adapter assembly
    Vehicle wire harness
    VTR/RR
    No. 1 stereo jack adapter assembly
    Vehicle wire harness

  2. E283642
    Unit check mode screen description
    Screen Description 
    Display
    Content
    *a: Device name
    Target device
    *b: History DTC
    Diagnostic memory results and stored DTCs are displayed.
    *c: Current DTC
    DTCs output in the service check are displayed.
    *d: DTC
    DTC (Diagnostic Trouble Code)
    *e: Timestamp
    The time and date of history DTCs are displayed. (The year is displayed in 2- digit format.)
    *f: Diagnosis clear switch
    Selecting "Code CLR" for 3 seconds clears the diagnostic memory data of the target device. (Both diagnostic system check result and the displayed data are cleared.)

    HINT:
    1. This screen is updated once per second.
    2. A maximum of 6 DTCs can be displayed for history and present DTCs.

  3. E287211
    Read the system check result.

    1. If the check result is "DETAIL", select the displayed check result to view the results on the "Unit Check Mode" screen and record them.

      NOTICE:
      A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit Check Mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit Check Mode" screen again to see if any other DTCs are displayed.

      HINT:
      1. When all results are "OK", no DTCs are present.
      2. When "NCON" is displayed for all devices connected via the AVC-LAN, or when all device names are not displayed, check if there is a short circuit in the AVCLAN or devices connected to the AVC-LAN. Repair or replace parts as necessary (Click here).
      3. When proceeding to view the results of another device, select the "Back" switch to return to the "System Check Mode" screen. Repeat the above step to view the results of other devices.

    2. Check the details of the DTC(s).

      NOTICE:
      The audio and visual system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the audio and visual system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

      System
      Proceed to
      Rear View Monitor System (for Radio and Display Type)*1
      Click here
      Rear Seat Entertainment System*2
      Click here
      1. *1: w/ Rear View Monitor System (for Radio and Display Type)
      2. *2: w/ Rear Seat Entertainment System


DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)

  1. E287212
    Clear DTCs

    1. Select "Memory CLR" for 3 seconds.

    2. Confirm that the check results are cleared.

      HINT:
      1. To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.
      2. When clearing DTCs using the "Unit Check Mode" screen, select "Code CLR" for 3 seconds.

  2. E287213
    Recheck

    1. Press the "Recheck" switch.

    2. E287214
      Confirm that all diagnostic codes are "OK" when the check results are displayed. If a result other than "OK" is displayed, perform troubleshooting again.

      HINT:
      When the DTCs are cleared using the "Unit Check Mode" screen, select "Back" to return to the "System Check Mode" screen and perform this operation.


FINISH DIAGNOSTIC MODE
  1. There are 2 methods to end diagnostic mode. Use one of them.

  2. Turn the ignition switch off.

  3. Press and hold the "SET UP" or "MENU" switch for 3 seconds.

← TERMINALS OF ECU (from Aug 2013)DTC CHECK / CLEAR (from Aug 2014) →