2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

AVC-LAN Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Each audio system component connected to the AVC-LAN (communication bus) transfers switch signals using the audio visual communication local area network.
If a short to +B or short to ground occurs in the AVC-LAN, the audio system will not function normally because communication is not possible.

WIRING DIAGRAM

E268495E02

INSPECTION PROCEDURE

HINT:
  1. The radio and display receiver assembly is the master unit.
  2. When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


1. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

  1. Remove the radio and display receiver assembly (Click here).E284331E02

    Text in Illustration 
    *A
    w/ Rear Seat Entertainment System
    *B
    w/ Side Monitor System
    *a
    Component without harness connected
    (Radio and Display Receiver Assembly)
    -
    -

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    7 (TX1+) - 8 (TX1-)
    Always
    60 to 80 Ω
    9 (TX+) - 10 (TX-)*1
    Always
    60 to 80 Ω
    7 (TX3+) - 8 (TX3-)*2
    Always
    60 to 80 Ω

    1. *1: w/ Rear Seat Entertainment System
    2. *2: w/ Side Monitor System



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
  1. *1: w/ Rear Seat Entertainment System
  2. *2: w/ Side Monitor System
  1. Disconnect the H50, H51 and H52 radio and display receiver assembly connectors.

  1. Disconnect the H63 stereo component amplifier assembly connector.

  1. Disconnect the W14 television display assembly connector*1.

  1. Disconnect the I6 parking assist ECU connector*2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H50-7 (TX3+) - I6-11 (TX+)*2
    Always
    Below 1 Ω
    H50-8 (TX3-) - I6-10 (TX-)*2
    Always
    Below 1 Ω
    H51-7 (TX1+) - H63-8 (TX+)
    Always
    Below 1 Ω
    H51-8 (TX1-) - H63-7 (TX-)
    Always
    Below 1 Ω
    H52-9 (TX+) - W14-3 (TX1+)*1
    Always
    Below 1 Ω
    H52-10 (TX-) - W14-4 (TX1-)*1
    Always
    Below 1 Ω
    H50-7 (TX3+) - Body ground*2
    Always
    10 kΩ or higher
    H50-8 (TX3-) - Body ground*2
    Always
    10 kΩ or higher
    H51-7 (TX1+) - Body ground
    Always
    10 kΩ or higher
    H51-8 (TX1-) - Body ground
    Always
    10 kΩ or higher
    H52-9 (TX+) - Body ground)*1
    Always
    10 kΩ or higher
    H52-10 (TX-) - Body ground*1
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT MALFUNCTIONING PARTS
  1. Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

    HINT:
    1. Check all slave units.
    2. When disconnecting a slave unit causes the master unit to return to normal operation, this indicates that the slave unit is malfunctioning. Replace the malfunctioning slave unit.

    OK:
    Master unit returns to normal operation.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

REPLACE MALFUNCTIONING PARTS


← Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier (from Aug 2014)AVC-LAN Circuit (from Aug 2014) →