2013-2015 Land Cruiser Prado · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. INSPECT DIFFERENTIAL RING GEAR BACKLASH

R012683E01
  1. Using SST and a dial indicator, measure the ring gear backlash.

    SST
    09564-32011  

    Standard backlash:
    0.11 to 0.21 mm (0.00433 to 0.00827 in.)

    If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.

    HINT:
    Perform the measurement at 3 or more positions around the circumference of the ring gear.


2. INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

F001237E16
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Distance from center to runout measurement point:
    30 mm (1.18 in.)

    Maximum Runout:
    Item
    Specified Condition
    Vertical runout
    0.15 mm (0.00591 in.)
    Lateral runout
    0.15 mm (0.00591 in.)

    Text in Illustration 
    *a
    Vertical Runout
    *b
    Lateral Runout
    If the runout is more than the maximum, replace the companion flange.


3. REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY

  1. C097021
    Using an E14 "TORX" socket wrench, remove the 4 bolts.

  1. Using a plastic-faced hammer, tap out the differential tube.


4. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

  1. R013209E01
    Using SST, remove the 2 oil seals.
    SST
    09308-00010  


5. REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT

F044234E01
  1. Using SST and a hammer, unstake the nut.

    SST
    09930-00010  

  1. SA02349E05
    Using SST to hold the companion flange, remove the nut.
    SST
    09330-00021  


6. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

F052175E06
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.


7. REMOVE FRONT DIFFERENTIAL DUST DEFLECTOR

F040564E02
  1. Using SST and a press, press out the dust deflector.

    SST
    09950-00020  
    09950-60010   (09951-00510)
    09950-70010   (09951-07150)

    NOTICE:
    Do not drop the companion flange.


8. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL

  1. SA02348E03
    Using SST, remove the oil seal from the differential carrier assembly.
    SST
    09308-10010  


9. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
  1. Remove the oil slinger from the drive pinion.


10. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER)

  1. F044343E03
    Using SST, remove the front tapered roller bearing (inner) from the drive pinion.
    SST
    09556-22010  


11. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER)

  1. W001770E06
    Using SST, remove the front tapered roller bearing (outer).
    SST
    09308-00010  


12. REMOVE FRONT DIFFERENTIAL OIL STORAGE RING
  1. Using a screwdriver and hammer, tap out the oil storage ring.


13. REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

C093595
  1. Remove the bearing spacer.


14. REMOVE DIFFERENTIAL SIDE BEARING RETAINER
  1. Using a screwdriver, remove the union.

  1. Remove the 10 bolts and tap out the side bearing retainer with a plastic-faced hammer.


15. REMOVE DIFFERENTIAL CASE ASSEMBLY

16. REMOVE DIFFERENTIAL DRIVE PINION

17. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (INNER)

  1. R002482E02
    Using SST and a press, remove the rear tapered roller bearing (inner) and washer from the drive pinion.
    SST
    09950-00020  

    HINT:
    If the drive gear or ring gear is damaged, replace them as a set.

    NOTICE:
    Do not drop the drive pinion.


18. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (OUTER)

  1. R013226
    Using a brass bar and hammer, remove the rear tapered roller bearing (outer).


19. REMOVE FRONT DIFFERENTIAL CASE BEARING

R013211E01

HINT:
  1. Measure the thickness of the case washer.
  2. Tag the bearing outer races so that they can be reinstalled in the correct locations.

  1. Using SST and a press, press out the case bearing (outer race) and case washer from the bearing retainer.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)
    If the bearing is damaged during removal, replace it.

  1. R013213E01
    Using SST and a press, press out the case bearing (outer race) and plate washer from the differential carrier.
    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)
    If the bearing is damaged during removal, replace it.


20. REMOVE DIFFERENTIAL RING GEAR

C113176E02
  1. Place matchmarks on the ring gear and differential case.

    Text in Illustration 
    *a
    Matchmark

  1. Remove the 10 ring gear set bolts.

  1. C014054E01
    Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


21. REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:
The differential case and case bearings should only be removed when replacement is necessary.

  1. R011392E03
    Using SST, remove the 2 differential case bearings (inner) from the differential case.
    SST
    09950-60010   (09951-00390)
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    Text in Illustration 
    *a
    Notch

    HINT:
    Set the claws of SST into the notches in the differential case.


22. REMOVE DIFFERENTIAL CASE ASSEMBLY

  1. C080046E01
    Using a chisel and hammer, unstake the differential case.

  1. G020264E01
    Using a 5 mm pin punch and hammer, tap out the straight pin.

  1. C216791E01
    Remove the parts shown in the illustration from the differential case.
    Text in Illustration 
    *1
    Differential Pinion Gear
    *2
    Differential Pinion Gear Thrust Washer
    *3
    Differential Pinion Shaft
    *4
    Differential Side Gear
    *5
    Differential Side Gear Thrust Washer


23. INSPECT DIFFERENTIAL GEAR KIT
  1. Check that the differential pinion and differential side gear are not damaged.
    If the differential pinion or differential side gear is damaged, replace the differential gear kit.


24. INSPECT FRONT DIFFERENTIAL CASE
  1. Check that the differential case is not damaged.
    If the differential case is damaged, replace it.


25. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

  1. R013199E01
    Using SST, tap out the oil seal from the differential tube.
    SST
    09308-00010  


26. REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH

  1. C097022
    Using a snap ring expander, remove the snap ring.

  1. Remove the side gear shaft from the differential tube.


27. REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH

  1. R013420E02
    Using a snap ring expander, remove the snap ring.

  1. Using SST, a brass bar and press, press out the bearing.

    SST
    09950-00020  

    NOTICE:
    1. Do not damage the bearing.
    2. Do not drop the shaft.

← REMOVAL (from Aug 2013)REASSEMBLY (from Aug 2013) →