2013-2015 Land Cruiser Prado · Service Manual Drivetrain

REASSEMBLY

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL TRANSFER LOW PLANETARY RING GEAR
  1. Install the low planetary ring gear to the front transfer case.

  1. F043456
    Using a screwdriver, install the snap ring.


2. INSTALL PIN

  1. F043455
    Install the pin.


3. INSTALL COMPRESSION SPRING
  1. Install the spring.


4. INSTALL TRANSFER CASE PLUG
  1. Install the transfer case plug.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }


5. INSTALL TRANSFER OUTPUT SHAFT PLATE WASHER

  1. F043476
    Install the washer.


6. INSTALL TRANSFER DRIVE SPROCKET BEARING
  1. Install the bearing.


7. INSTALL TRANSFER DRIVE SPROCKET SUB-ASSEMBLY
  1. Install the transfer drive sprocket.


8. INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER
  1. Install the output shaft spacer.


9. INSTALL REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING

  1. F044046E04
    Using SST and a press, install a new bearing.
    SST
    09316-60011   (09316-00011, 09316-00071)
    Text in Illustration 
    *1
    Groove
    V100135
    Rear

    NOTICE:
    Install the bearing so that the bearing snap ring groove faces the rear.


10. INSTALL TRANSFER OUTPUT SHAFT PLATE WASHER

  1. F043510
    Install the washer.


11. INSTALL TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING
  1. Install the needle roller bearing.


12. INSTALL TRANSFER CLUTCH HUB
  1. Install the transfer clutch hub.


13. INSTALL CENTER DIFFERENTIAL CASE

  1. F044051
    Install the center differential case.


14. INSTALL TRANSFER OUTPUT SHAFT SPACER BALL
  1. Install the ball.


15. INSTALL NO. 2 TRANSFER OUTPUT SHAFT SPACER
  1. Install the spacer.

  1. Using a snap ring expander, install the snap ring.


16. INSPECT DRIVE SPROCKET RADIAL CLEARANCE

F044050
  1. Using a dial indicator, measure the radial clearance of the drive sprocket.

    Standard clearance:
    0.01 to 0.06 mm (0.000394 to 0.0236 in.)

    Maximum clearance:
    0.06 mm (0.0236 in.)

    If the clearance is more than the maximum, replace the drive sprocket, rear output shaft or bearing.


17. INSPECT DRIVE SPROCKET THRUST CLEARANCE

F044049
  1. Using a feeler gauge, measure the thrust clearance of the drive sprocket.

    Standard clearance:
    0.15 to 0.24 mm (0.00591 to 0.00944 in.)

    Maximum clearance:
    0.24 mm (0.00944 in.)

    If the clearance is more than the maximum, replace the drive sprocket.


18. INSTALL TRANSFER INPUT SHAFT BEARING

  1. F043513E03
    Using SST and a press, install a new bearing with the groove facing forward.
    SST
    09223-15020  
    09515-30010  
    09950-70010   (09951-07100)


19. INSTALL TRANSFER INPUT BEARING SHAFT SNAP RING

F043468
  1. Select a new snap ring that allows minimal axial play.

    Standard Snap Ring Thickness:
    Mark
    Specified Condition
    1
    1.45 to 1.50 mm (0.0571 to 0.0591 in.)
    2
    1.50 to 1.55 mm (0.0591 to 0.0610 in.)
    3
    1.55 to 1.60 mm (0.0610 to 0.0630 in.)
    4
    1.60 to 1.65 mm (0.0630 to 0.0650 in.)
    5
    1.65 to 1.70 mm (0.0650 to 0.0669 in.)

  1. Using a snap ring expander, install the snap ring.


20. INSTALL TRANSFER LOW PLANETARY GEAR SPLINE PIECE

  1. F043507
    Using a screwdriver, install the low planetary gear spline piece and snap ring.


21. INSTALL TRANSFER LOW PLANETARY GEAR BEARING

F043469E03
  1. Using SST and a press, press in a new low planetary gear bearing.

    SST
    09950-60010   (09951-00570)
    09950-70010   (09951-07100)

    Press in depth:
    7.7 to 8.3 mm (0.304 to 0.326 in.)


22. INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING

  1. C216962
    Apply gear oil to 2 new seal rings.

  1. Install the 2 seal rings to the input shaft.

    NOTICE:
    When installing the seal ring, make sure not to expand it so that its inner diameter exceeds 65 mm (2.55 in.).


23. INSTALL TRANSFER LOW PLANETARY GEAR THRUST BEARING

  1. F043454E02
    Install the bearing.
    Text in Illustration 
    V100135
    Front


24. INSTALL NO. 1 TRANSFER THRUST BEARING RACE
  1. Install the thrust bearing race.


25. INSTALL TRANSFER INPUT SHAFT
  1. Install the transfer input shaft.


26. INSTALL MANUAL TRANSFER PLANETARY CARRIER WASHER

  1. F043453
    Install the washer.


27. INSTALL TRANSFER INPUT GEAR STOPPER BALL
  1. Install the ball.


28. INSTALL TRANSFER INPUT GEAR STOPPER
  1. Install the input gear stopper.


29. INSTALL TRANSFER INPUT GEAR STOPPER SHAFT SNAP RING

  1. F043514
    Select a new input gear stopper shaft snap ring that allows 0.05 to 0.15 mm (0.00197 to 0.00590 in.) of axial play.

    Standard Snap Ring Thickness:
    Specified Condition
    2.10 to 2.15 mm (0.0827 to 0.0846 in.)
    2.15 to 2.20 mm (0.0846 to 0.0866 in.)
    2.20 to 2.25 mm (0.0866 to 0.0886 in.)
    2.25 to 2.30 mm (0.0886 to 0.0906 in.)
    2.30 to 2.35 mm (0.0906 to 0.0925 in.)
    2.35 to 2.40 mm (0.0925 to 0.0945 in.)
    2.40 to 2.45 mm (0.0945 to 0.0965 in.)
    2.45 to 2.50 mm (0.0965 to 0.0984 in.)
    2.50 to 2.55 mm (0.0984 to 0.100 in.)
    2.55 to 2.60 mm (0.100 to 0.102 in.)
    2.60 to 2.65 mm (0.102 to 0.104 in.)
    2.65 to 2.70 mm (0.104 to 0.106 in.)
    2.70 to 2.75 mm (0.106 to 0.108 in.)
    2.75 to 2.80 mm (0.108 to 0.110 in.)
    2.80 to 2.85 mm (0.110 to 0.112 in.)
    2.85 to 2.90 mm (0.112 to 0.114 in.)
    2.90 to 2.95 mm (0.114 to 0.116 in.)
    2.95 to 3.00 mm (0.116 to 0.118 in.)
    3.00 to 3.05 mm (0.118 to 0.120 in.)

  1. Q007289
    Using a snap ring expander, install the snap ring.


30. INSTALL LOW PLANETARY GEAR ASSEMBLY WITH TRANSFER INPUT SHAFT SUB-ASSEMBLY

  1. F043450
    Install the low planetary gear together with the input shaft.

  1. F043449
    Using a snap ring expander, install the shaft snap ring.


31. INSTALL TRANSFER OIL PUMP GEAR

  1. F043448
    Install the transfer oil pump gear.


32. INSTALL TRANSFER OIL PUMP BODY O-RING

  1. F043463E01
    Coat a new O-ring with gear oil and install it to the oil pump body.


33. INSTALL TRANSFER OIL PUMP BODY SUB-ASSEMBLY

  1. F043447E02
    Install the oil pump body with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


34. INSTALL TRANSFER CASE MAGNET

35. INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY

  1. F043446
    Install the oil separator with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


36. INSTALL FILLER PLUG
  1. Install a new gasket and the filler plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


37. INSTALL DRAIN PLUG
  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


38. INSTALL TRANSFER SHIFT ACTUATOR ASSEMBLY

  1. C314513
    Install a new O-ring to the transfer shift actuator assembly.

  1. C218785E01
    Install the transfer shift actuator assembly with the 3 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Using a screwdriver and hammer, tap on the 2 snap rings.


39. INSTALL TRANSFER INPUT GEAR RADIAL BALL BEARING

  1. C216377E01
    Using SST and a press, install a new input gear radial ball bearing.
    SST
    09316-60011   (09316-00031)


40. INSTALL TRANSFER DRIVEN SPROCKET BEARING

  1. C216378E01
    Using SST and a press, install a new driven sprocket bearing.
    SST
    09316-60011   (09316-00071)


41. INSTALL REAR OUTPUT SHAFT SUB-ASSEMBLY, FRONT DRIVE CHAIN AND DRIVEN SPROCKET SUB-ASSEMBLY

  1. F043505
    Install the rear output shaft and drive sprocket to the front drive chain.

  1. F043441
    Install the rear output shaft, front drive chain and driven sprocket to the rear transfer case.

    HINT:
    Check that the rear output shaft and driven sprocket turn without much effort.

  1. Using a snap ring expander, install the snap ring.

    NOTICE:
    Make sure that the snap ring is firmly installed to the groove.


42. INSTALL CENTER DIFFERENTIAL LOCK FORK SUB-ASSEMBLY WITH FRONT DRIVE CLUTCH SLEEVE

  1. F043519E02
    Install the center differential lock fork and front drive clutch sleeve.
    Text in Illustration 
    V100135
    Front

    NOTICE:
    Install the clutch sleeve in the correct direction.

  1. Install the bolt.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

  1. Using a screwdriver and hammer, drive in the snap ring.


43. INSTALL NO. 2 TRANSFER GEAR SHIFT FORK SUB-ASSEMBLY WITH TRANSFER HIGH AND LOW CLUTCH SLEEVE

  1. F044401E04
    Install the No. 2 gear shift fork and high and low clutch sleeve.
    Text in Illustration 
    V100135
    Front

    NOTICE:
    Install the clutch sleeve in the correct direction.

  1. Install the bolt.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }


44. INSTALL TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING
  1. Install the needle roller bearing to the input shaft.


45. INSTALL TRANSFER OUTPUT SHAFT SPACER
  1. Install the transfer output shaft spacer to the input shaft.


46. INSTALL REAR TRANSFER CASE

  1. F043488E04
    Apply seal packing to the rear transfer case as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    If the removed rear transfer case is reused, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old seal packing on the rear transfer case contact surface, 2) clean off any remaining old seal packing from the rear transfer case contact surface, and 3) reapply seal packing to the rear transfer case.

  1. C218784E01
    Install the clamp and rear transfer case with the 12 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    Tighten the bolts of the rear transfer case within 10 minutes of applying the seal packing. The seal packing will dry very quickly.


47. INSTALL COLLAR

  1. F043432
    Install the collar.


48. INSTALL TRANSFER OUTPUT SHAFT WASHER
  1. Install the 2 washers.


49. INSTALL TRANSFER EXTENSION HOUSING SUB-ASSEMBLY

  1. F043489E03
    Apply seal packing to the extension housing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    If the removed extension housing is reused, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old seal packing on the housing contact surface, 2) clean off any remaining old seal packing from the housing contact surface, and 3) reapply seal packing to the housing.

  1. Apply adhesive to the threads of the bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. F043431E03
    Install the extension housing with the 5 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten the bolts of the extension housing within 10 minutes of applying the seal packing. The seal packing will dry very quickly.


50. INSTALL TRANSFER CASE REAR OIL SEAL

F043486E01
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the case upper surface.

    SST
    09223-46011  
    09631-32020  


51. INSTALL REAR TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL

  1. F043517E02
    Using SST and a hammer, tap in a new oil seal.
    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

  1. Coat the lip of the oil seal with MP grease.


52. INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

  1. C217384E01
    Apply gear oil to the connecting areas of the companion flange and output shaft.

  1. Install the companion flange to the output shaft.

    Text in Illustration 
    V100135
    Rear

  1. Using SST to hold the companion flange, install a new lock nut.

    SST
    09330-00021  

    Torque:
    118 N*m{ 1203 kgf*cm , 87 ft.*lbf }

  1. F050151E02
    Using a chisel and hammer, stake the lock nut.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

    NOTICE:
    1. Securely stake the shaft to the lock nut groove.
    2. Be careful not to damage the parts around the lock nut.
    3. Do not apply excessive force to the shaft.


53. INSTALL TRANSFER CASE FRONT OIL SEAL

C205242E01
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, tap in the oil seal until its metal ring contacts the case.

    SST
    09649-17010  
    09950-70010   (09951-07100)


54. INSTALL FRONT TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL

  1. F043517E02
    Using SST and a hammer, tap in a new oil seal.
    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

  1. Coat the lip of the oil seal with MP grease.


55. INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

C217366E01
  1. Apply gear oil to the connecting areas of the companion flange and driven sprocket.

  1. Install the companion flange to the driven sprocket.

    Text in Illustration 
    V100135
    Front

  1. Using SST to hold the companion flange, install a new lock nut.

    SST
    09330-00021  

    Torque:
    118 N*m{ 1203 kgf*cm , 87 ft.*lbf }

  1. F050151E02
    Using a chisel and hammer, stake the lock nut.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

    NOTICE:
    1. Securely stake the shaft to the lock nut groove.
    2. Be careful not to damage the parts around the lock nut.
    3. Do not apply excessive force to the shaft.


56. INSTALL BREATHER OIL DEFLECTOR
  1. Install the oil deflector.


57. INSTALL TRANSFER CASE COVER SUB-ASSEMBLY

  1. F043428E01
    Install the case cover with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


58. INSTALL TRANSFER BEARING RETAINER OIL SEAL RH

  1. F043518E02
    for A343F, A750F, G52F, R150F:
    Using SST and a hammer, drive in a new transfer bearing retainer oil seal RH until its surface is flush with the retainer upper surface.
    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07100)

  1. for RA61F:
    Using SST and a hammer, tap in 2 new transfer bearing retainer oil seals RH A and B as shown in the illustration.

    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07100)

    1. C264672E01
      for oil seal A:

      Drive in depth (A):
      43 to 44 mm (1.70 to 1.73 in.)

      Text in Illustration 
      *1
      Oil Seal A

    2. C264673E01
      for oil seal B:

      Drive in depth (B):
      53.5 to 54 mm (2.11 to 2.12 in.)

      Text in Illustration 
      *1
      Oil Seal B

  1. Coat the lip of the transfer bearing retainer oil seal RH with MP grease.


59. INSTALL TRANSFER BEARING RETAINER SUB-ASSEMBLY RH
  1. for RA61F:
    Install a new O-ring to the transfer bearing retainer sub-assembly RH.

    NOTICE:
    Apply MP grease to the O-ring when installing the transfer onto the transmission.

  1. F043490E03
    Apply seal packing to the transfer bearing retainer sub-assembly RH as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    If the removed transfer bearing retainer sub-assembly RH is reused, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old seal packing on the retainer contact surface, 2) clean off any remaining old seal packing from the retainer contact surface, and 3) reapply seal packing to the transfer bearing retainer sub-assembly RH.

  1. Apply sealant to the bolt threads.

    Sealant:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. F043427E01
    Install the transfer bearing retainer sub-assembly RH with the 5 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }

    NOTICE:
    Tighten the bolts of the transfer bearing retainer sub-assembly RH within 10 minutes of applying the seal packing. The seal packing will dry very quickly.


60. INSTALL HOSE

C216295
  1. Attach the clamp and install the hose.

← REASSEMBLY (Aug 2013 – Jul 2014)INSTALLATION (Aug 2013 – Jul 2014) →