2013-2015 Land Cruiser Prado · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

C215501
  1. Remove the clutch release fork with the clutch release bearing from the transmission unit.

  1. Remove the release fork support from the transmission unit.

  1. C163036
    Remove the clip and clutch release bearing from the clutch release fork.


2. REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

C215727
  1. Remove the 4 bolts.

  1. Using a plastic-faced hammer, remove the floor shift control shift lever retainer.


3. REMOVE SHIFT LEVER HOUSING

C215730
  1. Remove the bolt and shift lever housing.


4. REMOVE MANUAL TRANSMISSION CASE COVER

F051569
  1. Remove the 4 bolts and transmission case cover.


5. REMOVE SHIFT DETENT BALL PLUG

F051570
  1. Using a 10 mm hexagon socket wrench, remove the shift detent ball plug from the transfer adapter.

  1. Remove the ball and compression spring from the transfer adapter.


6. REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT
  1. Using a belt and wooden block, securely fasten the transmission to the workbench.

  1. C215728
    Using a chisel and hammer, unstake the rear set nut.

  1. C199426E03
    Engage 5th gear, and then secure the input shaft using SST.
    SST
    09322-35010   (09322-03010, 09322-03020, 09322-03030, 90105-12087, 90170-12030, 94622-51200)
    Text in Illustration 
    *1
    Input Shaft

    HINT:
    1. Install SST securely so that the part labeled A is in-line with the input shaft.
    2. Make sure that the part labeled A moves back and forth by hand after installing SST.

  1. C199433E01
    Using an L-type handle and SST, remove the rear set nut from the output shaft.
    SST
    09326-35010   (09326-03010)

  1. Remove the belt and wooden block from the transmission.

  1. C215729E01
    Remove the output shaft bearing and spacer.
    Text in Illustration 
    *1
    Output Shaft Bearing
    *2
    Output Shaft Spacer


7. REMOVE TRANSFER ADAPTER

C217228E01
  1. Remove the 10 bolts and 4 brackets.

    Text in Illustration 
    *1
    Bracket

  1. D033739
    Using a plastic-faced hammer, carefully tap off the transfer adapter to remove it.

    HINT:
    Place a brass bar against the rib portion of the case.


8. REMOVE MANUAL TRANSMISSION FILLER PLUG

F051572
  1. Remove the 2 transmission filler plugs and 2 gaskets from the transfer adapter.


9. REMOVE NO. 1 OIL RECEIVER PIPE

F051573
  1. Remove the No. 1 oil receiver pipe from the transfer adapter.


10. REMOVE OIL SEPARATOR PACKING SEAL

F051828
  1. Remove the oil separator packing seal from the transfer adapter.


11. REMOVE TRANSFER ADAPTER CASE PLUG

  1. C215734
    Using a 14 mm hexagon socket wrench, remove the case plug from the transfer adapter.


12. REMOVE REAR OUTPUT SHAFT BEARING

C217357E01
  1. Using SST, remove the 2 rear output shaft bearings (outer race) from the transfer adapter.

    SST
    09308-00010  


13. REMOVE COUNTER GEAR REAR RADIAL BALL BEARING

D033746
  1. Remove the bolt and bearing lock plate.

  1. C216330E01
    Using SST, remove the counter gear rear radial ball bearing from the transfer adapter.
    SST
    09308-00010  


14. REMOVE TRANSFER ADAPTER NEEDLE ROLLER BEARING
  1. Remove the roller bearing from the transfer adapter.


15. REMOVE TRANSMISSION OIL SEPARATOR

F051575
  1. Remove the 2 bolts and oil separator.


16. REMOVE REVERSE IDLER GEAR SHAFT BOLT

D033649
  1. Remove the reverse idler gear shaft bolt and gasket from the reverse idler gear shaft.


17. REMOVE TRANSMISSION MIDDLE CASE

  1. C215733E01
    Remove the bolt and collar.
    Text in Illustration 
    *1
    Bolt
    *2
    Collar

  1. C217230
    Remove the 11 bolts.

  1. D033741
    Using a plastic-faced hammer, carefully tap off the transmission middle case to remove it.

    HINT:
    Place a brass bar against the rib portion of the case.


18. REMOVE DRAIN PLUG SUB-ASSEMBLY

F051576
  1. Remove the drain plug and gasket from the transmission middle case.


19. REMOVE NO. 2 OIL RECEIVER PIPE

F051577
  1. Remove the No. 2 oil receiver pipe from the transmission middle case.


20. REMOVE SHIFT AND SELECT LEVER SHAFT

C215737
  1. Remove the shift and select lever shaft from the reverse gear shaft.


21. REMOVE SHIFT AND SELECT LEVER

  1. C215739
    Using a screwdriver, remove the E-ring.

  1. C215740
    Using a 5 mm pin punch and hammer, tap out the straight pin.

  1. C215738
    Remove the bolt, interlock plate, select cam and select lever from the lever shaft.

  1. Remove the lock ball pin and spring from the shift and select lever.


22. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

F051581E01
  1. Using SST, remove the back-up light switch and gasket.

    SST
    09817-16011  


23. INSPECT REVERSE IDLER GEAR THRUST CLEARANCE

  1. D033776
    Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.154 mm (0.00394 to 0.00606 in.)

    Maximum clearance:
    0.154 mm (0.00606 in.)

    1. If the clearance is more than the maximum, replace the reverse idler gear shaft, reverse idler gear or transmission front case.


24. REMOVE REVERSE IDLER GEAR

D033634
  1. Remove the reverse idler gear shaft, reverse idler gear bearing and reverse idler gear.


25. REMOVE FRONT TRANSMISSION CASE

F051582
  1. Remove the 4 bolts and interlock bracket.

  1. F051583
    Using a 27 mm hexagon wrench, remove the case plug.

  1. D033636
    Tie the input shaft, counter gear and control assembly with a piece of rope or string.

  1. D033637
    Expand the 2 snap rings and lift up the output shaft, input shaft, counter gear shaft and control assembly.

  1. D033638
    Remove the output shaft, input shaft, counter gear shaft and control assembly while gently tapping the clutch housing with a plastic-faced hammer.

    NOTICE:
    Take care not to subject the output shaft, input shaft, counter gear shaft and control assembly to any impact. This could cause the ball and spring to come out.

  1. Separate the output shaft, input shaft, counter gear shaft and control assembly.


26. REMOVE NO. 3 OIL RECEIVER PIPE

F051585
  1. Remove the No. 3 oil receiver pipe from the front transmission case.


27. REMOVE FRONT BEARING SHAFT SNAP RING

D033639
  1. Using snap ring pliers, remove the 2 snap rings.


28. REMOVE TRANSMISSION CASE OIL SEAL

C216331E01
  1. Using SST, remove the transmission case oil seal from the front transmission case.

    SST
    09308-00010  


29. REMOVE TRANSMISSION CASE NEEDLE BEARING

  1. Using SST, remove the bearing from the front transmission case.

    C215771E01

    Text in Illustration 
    *1
    Transmission Case Needle Bearing
    -
    -
    *a
    Hold
    *b
    Turn


30. REMOVE NO. 3 GEAR SHIFT FORK

F051588
  1. Remove the bolt and No. 3 gear shift fork.


31. REMOVE NO. 3 GEAR SHIFT FORK SHAFT

C232591
  1. Remove the No. 3 shift fork shaft, shift detent ball and compression spring.


32. REMOVE NO. 2 GEAR SHIFT FORK

F051589
  1. Remove the bolt and No. 2 gear shift fork.


33. REMOVE NO. 2 GEAR SHIFT FORK SHAFT

C232592
  1. Remove the No. 2 shift fork shaft, shift detent ball and compression spring.


34. REMOVE NO. 1 GEAR SHIFT FORK SHAFT

  1. D033718
    Using a 5 mm pin punch and hammer, tap out the slotted pin.

  1. C232593
    Remove the No. 1 shift fork shaft, shift detent ball, compression spring and No. 1 shift head.


35. REMOVE NO. 1 GEAR SHIFT FORK

D033720
  1. Using a 5 mm pin punch and hammer, tap out the slotted pin.

  1. D033721
    Remove the No. 2 shift head and No. 1 shift fork.


36. REMOVE NO. 4 GEAR SHIFT FORK

D033722
  1. Using a 5 mm pin punch and hammer, tap out the slotted pin.

  1. Remove the No. 4 shift fork.


37. REMOVE NO. 4 GEAR SHIFT FORK SHAFT

D033723
  1. Remove the No. 4 shift fork shaft, shift detent ball and compression spring.


38. REMOVE NO. 1 RELEASE ARM

D033724
  1. Using a screwdriver, remove the E-ring.

  1. D033725E02
    Remove the shift arm pivot and release arm.

← COMPONENTS (from Aug 2013)DISASSEMBLY (from Aug 2014) →