2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Operate the cooler compressor under the conditions shown below:

    Item
    Condition
    Engine Speed
    Idling
    Operating Time
    3 minutes or more
    A/C Switch Status
    On
    Blower Switch Status
    HI
    Set Temperature
    MAX COOL
    This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

    NOTICE:
    It is not necessary to operate the cooler compressor if the A/C does not operate because of compressor lock, etc.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.

    HINT:
    Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.


2. DRAIN ENGINE COOLANT
  1. for 1GR-FE:
    Drain the engine coolant (Click here).

  1. for 1KD-FTV:
    Drain the engine coolant (Click here).

  1. for 2TR-FE:
    Drain the engine coolant (Click here).

  1. for 5L-E:
    Drain the engine coolant (Click here).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (Click here)
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for Bolt Joint Type)

E200949
  1. Remove the 2 bolts.

  1. I043960E05
    Disconnect the air conditioning tube and accessory assembly.
    Text in Illustration 
    *a
    Disconnect tube by hand

    NOTICE:
    1. Do not use a screwdriver or similar tool to disconnect the tube.
    2. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

  1. Remove the grommet.

  1. Remove the 2 O-rings from the air conditioning tube and accessory assembly.


5. DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for Quick Joint Type)

E200950

  1. Using SST, remove the piping clamp.

    1. E112919E04
      Attach SST to the piping clamp.
      SST
      09870-00015  
      09870-00025  

      HINT:
      Confirm the direction of the piping clamp claw and SST by referring to the illustration on the caution label.

    2. E112920E04
      Push down SST and release the clamp lock.
      Text in Illustration 
      *1
      Release Lever
      *a
      Push
      *b
      Pull

      NOTICE:
      Be careful not to deform the tubes when pushing SST.

    3. Pull SST slightly and push the release lever, then remove the piping clamp with SST.

    4. Remove the piping clamp from SST.

    5. Disconnect the air conditioning tube and accessory assembly.

      NOTICE:
      Cap the open fittings immediately to keep moisture or dirt out of the system.

  1. Remove the grommet.


6. DISCONNECT HEATER WATER INLET HOSE AND HEATER WATER OUTLET HOSE

  1. Using pliers, grip the claws of the clips and slide the 2 clips.

    E204000E01

    Text in Illustration 
    *A
    for 1GR-FE, for Single Air Conditioning System
    *B
    for 1KD-FTV, for Single Air Conditioning System
    *C
    for 5L-E, for Single Air Conditioning System
    *D
    for 2TR-FE, for Single Air Conditioning System
    *E
    for 1GR-FE, for Dual Air Conditioning System
    *F
    for 1KD-FTV, for Dual Air Conditioning System
    *G
    for 5L-E, for Dual Air Conditioning System
    *H
    for 2TR-FE, for Dual Air Conditioning System

  1. Disconnect the 2 heater water hoses.


7. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
  1. Remove the windshield wiper motor assembly (Click here).


8. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
  1. Remove the instrument panel sub-assembly (Click here).


9. REMOVE STEERING COLUMN ASSEMBLY
  1. for Power Tilt and Power Telescopic Steering Column:
    Remove the steering column assembly (Click here).

  1. for Manual Tilt and Manual Telescopic Steering Column:
    Remove the steering column assembly (Click here).


10. REMOVE FRONT SEAT ASSEMBLY LH
  1. for Manual Seat:
    Remove the front seat assembly LH (Click here).

  1. for Power Seat:
    Remove the front seat assembly LH (Click here).

  1. for Walk in Seat Type:
    Remove the front seat assembly LH (Click here).

  1. for Bench Seat Type:
    Remove the front seat assembly LH (Click here).


11. REMOVE FRONT SEAT ASSEMBLY RH
  1. for Manual Seat:
    Remove the front seat assembly RH (Click here).

  1. for Power Seat:
    Remove the front seat assembly RH (Click here).

  1. for Walk in Seat Type:
    Remove the front seat assembly RH (Click here).

  1. for Bench Seat Type:
    Remove the front seat assembly RH (Click here).


12. REMOVE FRONT FLOOR CARPET ASSEMBLY

NOTICE:
It is not necessary to fully remove the floor carpet. Partially remove it so that the rear air duct can be removed in a later step.


13. REMOVE REAR NO. 3 AIR DUCT

  1. E198787
    Detach the 3 clamps and 6 claws and remove the rear No. 3 air duct.


14. REMOVE REAR NO. 1 AIR DUCT

  1. E198788
    Detach the 3 clamps and 6 claws and the rear No. 1 air duct.


15. REMOVE NO. 1 CONSOLE BOX DUCT

  1. E198789E01
    Remove the clip and No. 1 console box duct.
    Text in Illustration 
    *A
    Automatic Transmission
    *B
    Manual Transmission


16. REMOVE NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET LH

  1. E198792
    Remove the 2 nuts, bolt and No. 1 instrument panel brace mounting bracket LH.


17. REMOVE NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET RH

  1. E198793
    Remove the 2 nuts, bolt and No. 1 instrument panel brace mounting bracket RH.


18. REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY

  1. E198790
    Detach the 3 claws and No. 1 air duct sub-assembly.


19. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY

  1. E204225
    Remove the screw.

  1. Detach the 2 claws and remove the No. 2 air duct sub-assembly.


20. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

  1. Disconnect the clamps and connectors.

    E198795

  1. Remove the bolts, nuts and wire harness.

    E198794

  1. Remove the instrument panel reinforcement assembly with air conditioning unit assembly.

    E198796

    1. Remove the 5 caps.

    2. Using a T40 "TORX" socket, remove the 5 "TORX" bolts.

    3. Using a 12 mm hexagon wrench, loosen the 2 collars.

    4. Remove the bolts, nuts and the instrument panel reinforcement assembly with air conditioning unit assembly.


21. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

  1. Detach the 2 claws and remove the 5 bolts and instrument panel reinforcement assembly.

    E200782

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →