B15D3 Stereo Component Amplifier Disconnected
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The navigation receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication.When an AVC-LAN communication error occurs between the navigation receiver assembly and stereo component amplifier assembly, this DTC will be stored.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B15D3 |
When either condition below is met:
|
|
- HINT:
- Even if no fault is present, this DTC may be stored depending on the battery condition.
- The navigation receiver assembly is the master unit.
- Even if no fault is present, this DTC may be stored depending on the battery condition.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).
| 1. CHECK FOR DTC |
If DTC B15C3 is output, perform the troubleshooting of DTC B15C3 first.
Result Result
Proceed to
DTC B15C3 is not output.
A
DTC B15C3 is output.
B
|
|
||||
| A | |
| 2. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING) |
Check that optional components (including associated wiring) which generate radio waves are not installed.
Result Result
Proceed to
Optional components (including associated wiring) are installed.
A
Optional components (including associated wiring) are not installed.
B
- HINT:
- Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
- This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
- Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
|
|
||||
| A | |
| 3. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING) |
Remove optional components (including associated wiring).
- NOTICE:
- Do not remove optional components or associated wiring without the permission of the customer.
| NEXT | |
| 4. CHECK FOR DTC |
Clear the DTCs (Click here).
Recheck for DTCs and check if the same DTC is output again (Click here).
- OK:
- No DTCs are output.
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND) |
Disconnect the stereo component amplifier assembly connectors.


Text in Illustration *A
for JBL Made
*B
except JBL Made
*a
Front view of wire harness connector
(to Stereo Component Amplifier Assembly)
-
-
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for JBL Made Tester Connection
Condition
Specified Condition
H64-2 (GND) - Body ground
Always
Below 1 Ω
H64-6 (GND2) - Body ground
Always
Below 1 Ω
except JBL Made Tester Connection
Condition
Specified Condition
H67-3 (GND) - Body ground
Always
Below 1 Ω
H67-18 (GND2) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for JBL Made Tester Connection
Condition
Specified Condition
H64-1 (+B) - H64-2 (GND)
Always
11 to 14 V
H64-3 (+B2) - H64-2 (GND)
Always
11 to 14 V
H63-12 (ACC) - H64-2 (GND)
Engine switch on (ACC)
11 to 14 V
except JBL Made Tester Connection
Condition
Specified Condition
H67-1 (+B) - H67-3 (GND)
Always
11 to 14 V
H67-16 (+B2) - H67-3 (GND)
Always
11 to 14 V
H63-12 (ACC) - H67-3 (GND)
Engine switch on (ACC)
11 to 14 V
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY) |
Disconnect the H56 navigation receiver assembly connector.
Disconnect the H63 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H56-7 (TX1+) - H63-8 (TX+)
Always
Below 1 Ω
H56-8 (TX1-) - H63-7 (TX-)
Always
Below 1 Ω
H56-7 (TX1+) - Body ground
Always
10 kΩ or higher
H56-8 (TX1-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY |
Replace the stereo component amplifier assembly with a known good one (Click here).
Clear the DTCs (Click here).
Recheck for DTCs and check if the same DTC is output again.
- OK:
- No DTCs are output.
|
|
||||
| OK | ||
| ||
