2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

B15D3 Stereo Component Amplifier Disconnected

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The navigation receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication.
When an AVC-LAN communication error occurs between the navigation receiver assembly and stereo component amplifier assembly, this DTC will be stored.
DTC Code
DTC Detection Condition
Trouble Area
B15D3
When either condition below is met:
  1. Stereo component amplifier assembly is/was not connected while the engine switch is on (ACC) or on (IG).
  2. Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started.
  1. Stereo component amplifier assembly
  2. Navigation receiver assembly
  3. Harness or connector

HINT:
  1. Even if no fault is present, this DTC may be stored depending on the battery condition.
  2. The navigation receiver assembly is the master unit.


WIRING DIAGRAM

E286231E07

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


1. CHECK FOR DTC
  1. If DTC B15C3 is output, perform the troubleshooting of DTC B15C3 first.

    Result 
    Result
    Proceed to
    DTC B15C3 is not output.
    A
    DTC B15C3 is output.
    B



B
GO TO DTC "B15C3" IN DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


2. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check that optional components (including associated wiring) which generate radio waves are not installed.

    Result 
    Result
    Proceed to
    Optional components (including associated wiring) are installed.
    A
    Optional components (including associated wiring) are not installed.
    B

    HINT:
    1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
    2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 4
A


3. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


4. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
Go to step 5
OK

END (COMMUNICATION MALFUNCTION DUE TO NOISE)

5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)

  1. Disconnect the stereo component amplifier assembly connectors.E286233E01

    Text in Illustration 
    *A
    for JBL Made
    *B
    except JBL Made
    *a
    Front view of wire harness connector
    (to Stereo Component Amplifier Assembly)
    -
    -

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for JBL Made 
    Tester Connection
    Condition
    Specified Condition
    H64-2 (GND) - Body ground
    Always
    Below 1 Ω
    H64-6 (GND2) - Body ground
    Always
    Below 1 Ω
    except JBL Made 
    Tester Connection
    Condition
    Specified Condition
    H67-3 (GND) - Body ground
    Always
    Below 1 Ω
    H67-18 (GND2) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for JBL Made 
    Tester Connection
    Condition
    Specified Condition
    H64-1 (+B) - H64-2 (GND)
    Always
    11 to 14 V
    H64-3 (+B2) - H64-2 (GND)
    Always
    11 to 14 V
    H63-12 (ACC) - H64-2 (GND)
    Engine switch on (ACC)
    11 to 14 V
    except JBL Made 
    Tester Connection
    Condition
    Specified Condition
    H67-1 (+B) - H67-3 (GND)
    Always
    11 to 14 V
    H67-16 (+B2) - H67-3 (GND)
    Always
    11 to 14 V
    H63-12 (ACC) - H67-3 (GND)
    Engine switch on (ACC)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
  1. Disconnect the H56 navigation receiver assembly connector.

  1. Disconnect the H63 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H56-7 (TX1+) - H63-8 (TX+)
    Always
    Below 1 Ω
    H56-8 (TX1-) - H63-7 (TX-)
    Always
    Below 1 Ω
    H56-7 (TX1+) - Body ground
    Always
    10 kΩ or higher
    H56-8 (TX1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly with a known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)


← B15C3 Speaker Output Short (from Aug 2014)B15D3 Stereo Component Amplifier Disconnected (from Aug 2014) →