2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

B15D5 Rear Seat Entertainment System Disconnected

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The navigation receiver assembly and television display assembly are connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the navigation receiver assembly and television display assembly, these DTCs will be stored.
DTC Code
DTC Detection Condition
Trouble Area
B15D5
When either condition below is met:
  1. The television display assembly is/was not connected while the engine switch is on (IG or ACC).
  2. Communication between master unit and the television display assembly is not possible when the engine is started.
  1. AVC-LAN communication line
  2. Television display assembly
  3. Navigation receiver assembly
  4. Harness or connector

HINT:
  1. Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The navigation receiver assembly is the master unit.


WIRING DIAGRAM

E286270E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK CONNECTOR CONNECTION CONDITION
  1. Check that the television display assembly and navigation receiver assembly connectors are connected properly.

    OK:
    The connectors are connected properly.



NG
CONNECT CONNECTOR CORRECTLY
OK


3. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)

  1. E192430E72
    Disconnect the television display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W14-17 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    W14-1 (+B) - W14-17 (GND)
    Always
    11 to 14 V
    W14-2 (ACC) - W14-17 (GND)
    Engine switch off
    Below 1 V
    W14-2 (ACC) - W14-17 (GND)
    Engine switch on (ACC)
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Television Display Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
  1. Disconnect the W14 television display assembly connector.

  1. Disconnect the H57 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W14-3 (TX1+) - H57-9 (TX+)
    Always
    Below 1 Ω
    W14-4 (TX1-) -H57-10 (TX-)
    Always
    Below 1 Ω
    W14-3 (TX1+) - Body ground
    Always
    10 kΩ or higher
    W14-4 (TX1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK TELEVISION DISPLAY ASSEMBLY
  1. Replace the television display assembly with a known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (TELEVISION DISPLAY ASSEMBLY IS DEFECTIVE)


← B15D5 Rear Seat Entertainment System Disconnected (Aug 2013 – Jul 2014)B15D8 Monitor Disconnected (Aug 2013 – Jul 2014) →