B15D8 Monitor Disconnected
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The parking assist ECU and navigation receiver assembly are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the navigation receiver assembly and parking assist ECU, these DTCs will be stored.| DTC Code |
DTC Detection Condition |
Trouble Area |
| B15D8* |
A device that is listed in the AVC-LAN connected device record of the master unit is missing. |
|
- HINT:
- *: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
- The navigation receiver assembly is the master unit.
- *: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK DTC |
Recheck for DTCs and check if the same DTC is output again (Click here).
- OK:
- No DTCs are output.
|
|
||||
| OK | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND) |
Disconnect the parking assist ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I6-4 (GND1) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
I6-1 (+B) - I6-4 (GND1)
Always
11 to 14 V
I6-8 (IG) - I6-4 (GND1)
Engine switch on (IG)
11 to 14 V
I6-9 (ACC) - I6-4 (GND1)
Engine switch on (ACC)
11 to 14 V
| *a |
Front view of wire harness connector (to Parking Assist ECU) |
|
|
||||
| OK | |
| 4. INSPECT NAVIGATION RECEIVER ASSEMBLY |
Remove the navigation receiver assembly (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
7 (TX3+) - 8 (TX3-)
Always
60 to 80 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARKING ASSIST ECU) |
Disconnect the H55 navigation receiver assembly connector.
Disconnect the I6 parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H55-7 (TX3+) - I6-11 (TX+)
Always
Below 1 Ω
H55-8 (TX3-) - I6-10 (TX-)
Always
Below 1 Ω
H55-7 (TX3+) - Body ground
Always
10 kΩ or higher
H55-8 (TX3-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. REPLACE PARKING ASSIST ECU |
Replace the parking assist ECU with a new or normally functioning one.
- for LHD: Click here
- for RHD: Click here
- for LHD: Click here
| NEXT | |
| 7. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 8. CHECK DTC |
Recheck for DTCs and check if the same DTC is output again (Click here).
|
|
||||
| OK | ||
| ||
